Transcript
Setup Guide — DVI 201 / HDMI 201 Series
Setup Guide — DVI 201 / HDMI 201 Series
This guide provides instructions for an experienced installer to set up and operate the Extron® DVI 201 and HDMI 201 Extenders.
N If necessary, after power is applied, test for proper cable connection as follows: 1. Plug both TP cables into the unit to be powered.
Momentarily connect either of the cables on the opposite end into the unpowered unit‘s “2” connector. If the unpowered unit’s Power LED is lit, the connection is correct. If the unpowered unit’s Power LED is not lit, unplug the connector on the unpowered end and connect the other cable to the “2” connector. • (Decora only) Audio connector — Connect a 5-wire audio cable between these 3.5 mm, 5-pole direct insertion connectors to pass audio between the transmitter and receiver.
N Wall-mounted (Decora® [DVI 201 A D
and HDMI 201 A D]) units are partially compatible with non-wall mounted units. Both handle video and serial (RS-232) data. Decora units also passively handle audio.
Installation
2.
N Step 1 is for Decora units only. For non-wall mounted units, skip to Step 2.
Transmitter
Wall Stud
Cable
Balanced output
T Use a level to mark the opening. c. Secure the wall box with 10-penny nails or #8 or #10 screws, leaving the front edge flush with the surface.
Screws or Nails
Do not tin the wires!
wired unit, such as a switcher, an amplifier, or powered speakers.
The free end of a cable to the receiver can also be connected directly to any compatibly wired audio source.
Step 6 — Outputs from the receiver
Turn off or disconnect all equipment power sources.
• DVI / HDMI output connector — Connect a DVI or HDMI cable between this port and the input port of the display.
Step 3 — Mounting Non-Decora units
• (Decora only) Audio output — Connect a stereo audio device to this 3.5 mm mini stereo jack (DVI 201) or set of RCA connectors (HDMI 201) to receive the passed through unbalanced audio.
Mount the non-Decora units as required.
Step 4 — Inputs to the transmitter DVI
N Except for the audio connector, non-Decora unit features shown. • DVI / HDMI input connector — Connect a DVI or HDMI cable between this port and the output port of the digital video source.
HDMI
REMOTE
• (Non-Decora only) DDC Route DIP switch — If the local output is not used, set the DDC Route DIP switch to remote. Ensure that you power the display first before the video source.
• RS-232 Pass-Thru connector — Plug an RS-232 or modulated IR device into the RS-232 Pass-Thru port, as shown below. Receive Transmit Ground
SPARE
LOCAL
AUDIO-R AUDIO L+R AUDIO-L
Tie Wrap
Power Supply Output Cord
Step 8 — Final installation (Decora units)
Decora Faceplate
a. Make all connections, test the system, and install the device when operation is satisfactory. b. At the power outlet, unplug the power supply.
T PU
IN
SINGLE LINK
c. Mount the transmitter or receiver into the wall box, and attach the supplied Decora faceplate to the unit.
Extron USA - West Headquarters
• Connect transmitter output 1 to receiver input 1.
+800.633.9876
• Connect transmitter output 2 to receiver input 2.
+1.714.491.1500 +1.714.491.1517 FAX
Inside USA / Canada Only
1
2
I
DV
IN
AU
-232 RS THRU SS Tx PA Rx
Extron DVI 201 A D
d. At the power outlet, reconnect the power supply. This powers up both units.
Extron recommends DTP26 cable or equivalent.
3" 16 (5 mm) Max.
SECTION A–A
Wire the 2-pole captive screw connector for the included external 12 VDC power supply as shown at right. Plug the power supply into either unit; the powered unit powers the other unit.
DI
HDMI 201
Captive Screw Connector
A
O
DVI 201 Tx Rx Gnd
Ridges
A
Step 7 — Power
• (Non-Decora only) Local output — If desired, connect a DVI or HDMI monitor for local monitoring of the input digital image.
• (Decora only) Audio input — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack (DVI 201) or set of RCA connectors (HDMI 201).
Smooth
• RS-232 Pass-Thru connector — Plug an RS-232 or modulated IR device into the RS-232 Pass-Thru port. Wire the connector as shown for step 4.
Decora units may have a different appearance.
N For best results, use shielded cables. For resolutions of 1920x1200, 1080p, or 1600x1200,
Sleeve (s) Tip Ring
N The free end of a cable from the transmitter can also be connected directly to any compatibly
Step 2 — Power
Step 5 — Cables between units
Tip Ring
Sleeve (s) Ring Tip
T In order to fit in the junction box, do not install a boot on TP cables and RJ-45 connectors.
Connected RS-232 Device Pins
Balanced Input
Ring Tip
Wall opening is flush with edge of box.
d. Run all required cables (see steps 4, 5, and 6) and secure them with cable clamps.
Tip Sleeve
R
b. Cut out the material from the marked area.
CAUTION
For the transmitter’s unbalanced audio output, connect the sleeve(s) to the ground contact. DO NOT connect the sleeve(s) to the negative (-) contacts.
L
Cable Clamp
Tip Sleeve
R
a. Place the wall box against the installation surface, and mark the opening guidelines.
NO GROUND HERE. Tip Sleeve (s) NO GROUND HERE. Tip
L
Step 1 — Preparing the mounting surface (Decora units) N Use a wall box with a depth of at least 2.5 inches (6.4 cm).
Receiver
Unbalanced Input
Unbalanced output
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655 +81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800 +971.4.2991880 FAX
+1.919.863.1794 +1.919.863.1797 FAX
+31.33.453.4040 +31.33.453.4050 FAX
+65.6383.4400 +65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2010 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568 +86.21.3760.1566 FAX
68-1034-50 Rev. B 04 10
