Transcript
SFBD-155E2J1R Small Form Factor Bi-Directional Transceiver Module for Fast Ethernet, ATM, SONET OC-3/SDH STM-1 FEATURES RoHS compliant 2x5 Pin SFF Package with SC Receptacle Single Mode Fiber, Bi-Directional Transmission with 1310nm Transmitter and 1550nm Receiver Link Distance up to 15km Single +3.3V power supply and PECL logic interface Wave Solderable and Aqueous Washable Bellcore GR-468 compliant Laser Class 1 Product which comply with the requirements of IEC 60825-1 and IEC 60825-2
Description
Application
DELTA’s SFF Bi-Directional transceiver is designed for point-to-point Bi-Directional Optical Network transmission. The module consists
TTC TS-1000
1310nm FP laser, InGaAs PIN, Preamplifier and WDM filter in a high-integrated optical sub-assembly, and it receives up to 155Mbps of continuous data at 1550nm, and transmits 155Mbps of continuous data at 1310nm. The module is contained in a 2x5 SFF industry standard package with a SC receptacle connector, and support LVTTL transmitter disable
IEEE 802.3ah 100BASE-BX/ Fast Ethernet
ITU-T G.985
SONET OC-3/SDH STM-1/ ATM Network FTTx Broadband Access System
Performance
input, LVPECL electrical signal Interface and receiver signal detect output.
SFBD-155E2J1R data link up to 15km in 9/125um single mode fiber.
1 DELTA ELECTRONICS, INC.
Revision: S1 09/12/2006
www.deltaww.com
SFBD-155E2J1R 1. Absolute Maximum Ratings Parameter Storage Temperature Operating Ambient Temperature Storage Ambient Humidity Power Supply Voltage Signal Input Voltage Optical Input Power (Peak) Lead Soldering Temperature Lead Soldering Time
Symbol Ts Ta HA VCC
Min. -40 -10 5 -0.5 -0.3
Typ.
Max. 85 80 95 5 Vcc+0.3 0 260 10
Unit ºC ºC % V V dBm ºC sec
Min. 0 5 3.135
Typ.
Max. 70 85 3.465 230 100 155.52 15
Unit ºC % V mA mVp-p Mbps km
Max. -8 -5
Unit dBm dBm dB nm nm ns ns dB dB/Hz
TSOLD tSOLD
Note
2. Recommended Operating Conditions Parameter Ambient Operating Temperature Ambient Humidity Power Supply Voltage Power Supply Current Power Supply Noise Rejection Data Rate Transmission Distance
Symbol TA HA VCC ICC
3.3
10
Note Without air flow Non-condensing
100Hz to 1MHz
3. Optical Specification of Transmitter Parameter Average Launched Power Launched power (Peak.) Extinction Ratio Center Wavelength Spectrum Width (RMS) Optical Rise/Fall Time Total Jitter Optical Return Loss Tolerance Relative Intensity Noise Output Eye Mask
Symbol PO
Min. -14
Typ. -11
ER 8.5 λC 1260 1310 1360 σ 6 tr/tf 1.3 tJ 1 ORLT 14 RIN -116 Compliant with Bellcore TR-NWT-000253 and ITU recommendation G.957
FP Laser Note (2) Note (3)
Note (4)
Note (1). Launched power (avg.) is power coupled into a single mode fiber. Note (2). These are unfiltered 20-80% values. Note (3). Measure at 223-1 NRZ PRBS pattern. 1.20 Note (4). Eye Mask definition 1.00 Amplitude
Note Note (1)
Mean level of logical "1"
0.80 0.50 0.20 0.00
Mean level of logical "0"
-0.20 0.00 0.15
0.35
0.65
0.85 1.00
Time
Optical Pulse Mask with Bessel Filter Specified in ITU-T G.957
2 DELTA ELECTRONICS, INC.
Revision: S1 09/12/2006
www.deltaww.com
SFBD-155E2J1R 4. Optical Specification of Receiver Parameter Input Optical Wavelength Receiver Sensitivity Input Saturation Power (Overload) Signal Detect -Assert Power Signal Detect -Deassert Power Signal Detect Hysteresis Optical Receiver Reflectance Output Data Rise/Fall time S/X Endurance Optical Isolation
Symbol λIN PIN PSAT PA PD PA-PD
Min. 1480 -3 -44 0.5
Typ.
Max. 1600 -30 -30
2.5
tr/tf
6 -14 1.5 10
25
Unit nm dBm dBm dBm dBm dB dB ns dB dB
Note PIN-PD Note (1)
Note (2) Note (3) Note (4) Note (5) Note (6)
Note (1). Measured with 1520nm, ER=10dB; BER =<10-10@PRBS=223-1 NRZ Note (2). When SD deasserted, the data output is Low-level (fixed) Note (3). When the terminal is viewed from the optical path, the reflection toward the optical path of the optical signal with a central wavelength of 1480nm to 1580nm transmitted to terminal. Note (4). These are 20%~80% values Note (5). X=10 MHz, Rectangular BER =10-10 Note (6). Receiver isolation between 1260nm ~1360nm
5. Electrical Interface Characteristics Parameter Transmitter Total Supply Current Differential line input Impedance Differential Data Input Swing Data Input Voltage- High Data Input Voltage- Low Transmitter Disable Input-High Transmitter Disable Input-Low Receiver Total Supply Current Differential Data Output Swing Data Output Voltage-High Data Output Voltage-Low Signal Detect Output Voltage-High Signal Detect Output Voltage-Low
Symbol
Min.
Typ.
ICC RIN VDT VIH-VCC VIL-VCC VDISH VDISL
80 300 -1.165 -1.810 2 0
100
ICC VDR VOH-VCC VOL-VCC VOH-VCC VOL-VCC
400 -1.085 -1.830 -1.085 -1.830
Max.
Unit
Note
A 120 1600 -0.880 -1.475 VCC+0.3 0.8
mA Ohm mVp-p V V V V
Note (1)
B 2000 -0.880 -1.555 -0.880 -1.555
mA mVp-p V V V V
LVPECL LVTTL Note (1)
LVPECL
Note (1). A (TX)+ B (RX) = 230mA (A: Not include termination circuit; B: using a resister of 150Ω between Data-output and ground)
3 DELTA ELECTRONICS, INC.
Revision: S1 09/12/2006
www.deltaww.com
SFBD-155E2J1R 6. Pin Description Tx/Rx
Rx
Tx
Pin No.
I/O
Pin Name
Description
1
VeeR
Receiver Ground
2
VccR
+3.3V Receiver Power Supply Normal Optical Input indicated by logic “High”, and No Optical Input indicated by logic “Low”.
3
O
SD
4
O
RD(n)
Inverted Receiver Data Output
5
O
RD(p)
Non-Inverted Receiver Data Output
6
VccT
+3.3V Transmitter Power Supply
7
VeeT
Transmitter Ground
8
I
Tx_Dis
LVTTL Logic “High” to Disable Transmitter, and Enable Transmitter by Logic “Low” or “Open”.
9
I
TD(p)
Non-Inverted Transmitter Data Input
10
I
TD(n)
Inverted Transmitter Data Input
MS
Mounting studs/ connect this pin to Chassis ground
MS
Bottom View MS
4 DELTA ELECTRONICS, INC.
Revision: S1 09/12/2006
www.deltaww.com
SFBD-155E2J1R 7. Recommended Interface Circuit (AC Coupling)
DELTA SFF Module 1uH
3.3V 10uF
6. VccT 100nF
100nF 1uH
8. Tx_Dis
Tx_Dis
3.3V 130ohm
82ohm
9. TD(p)
Z0=50ohm
Transmitter
100nF 10. TD(n)
Z0=50ohm 100nF 150ohm
130ohm
82ohm
150ohm
7. VeeT
3.3V
Protocol IC
2. VccR
SerDes IC 10uF
3.3V 82ohm
100nF
130ohm 5. RD(p)
Z0=50ohm 100nF
4. RD(n)
Z0=50ohm 100nF 82ohm
130ohm
150ohm
SD 3.3V 270ohm
5 DELTA ELECTRONICS, INC.
Receiver
150ohm 3. SD 1. VeeR
Revision: S1 09/12/2006
www.deltaww.com
SFBD-155E2J1R 8. Outline Dimensions Parameter Mechanical Dimensions Connector Type
Unit mm -
Description 49.2x13.5x9.6 SC Receptacle Connector
Note IEC-61754-4
XXXXXXXXXXXXXX
13.50
4.63
0.30
7.20
1.0± 0.05
10.16 ± 0.1
49.19
Protective Cover
DIMENSIONAL TOLERANCES : ± 0.2 Unit : mm
Week (52Weeks/Year) : 1月2日=01
6 DELTA ELECTRONICS, INC.
Revision: S1 09/12/2006
www.deltaww.com
SFBD-155E2J1R 9. Regulatory Compliance Feature Electrostatic Discharge (ESD) to the Electrical Pins
Test Method Reference Performance Human Body Model MIL-STD-883E Method 3015.7 (HBM) EIA-JESD22-A114 (1) Satisfied with Machine Model (MM) EIA-JESD22-A115
Electrostatic Discharge
Contact Discharge
(ESD) to the Simplex Receptacle
Air Discharge
IEC/EN 61000-4-2 IEC/EN 61000-4-3
Radio Frequency Electromagnetic Field Immunity
electrical characteristics of product spec. (2) No physical damage
FCC Part 15 Class B EN 55022 Class B (CISPR 22A)
Electromagnetic Interference (EMI)
Laser Eye Safety
IEC/EN 61000-4-2
FDA/CDRH
FDA 21CFR 1040.10, 1040.11
CDRH File # 0420993
TUV
IEC/EN 60825-1
TUV
IEC/EN 60825-2
R50032471
TUV
IEC/EN 60950
UL/CSA
UL 60950
Certificate
#
Component Recognition UL File # E239394
Appendix A. Document Revision Version No. S0 S1
Date 2006-05-10 2006-09-12
Description Preliminary datasheet Add barcode on product label
7 DELTA ELECTRONICS, INC.
Revision: S1 09/12/2006
www.deltaww.com
