Transcript
Statement Copyright © 2015 IPCamPower.com This document contains proprietary information that is protected by copyright. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language,
USER GUIDE POE & Optical Transmission
in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written permission of our company. The information and product specifications within this document are subject to change at any time, without notice and without obligation to notify any person of such change.
POE Extender
Packing List A POE extender User Guide
Product Feature
Mechanical strcuture and Port description
Product introduction The IPCP-EXT2P PoE Extender allows for an incoming PoE powered signal to be extended to 1 or 2 PoE powered devices. This takes down the barrier of a typical 100 meter distance restriction of PoE and can extend it to even further distances. Furthermore, this extender is powered by the incoming PoE power
25mm
of your PoE switch or injector (not included), therefore you do not have to worry about having a nearby power recptacle to power this device. Additionally, this device acts as a PoE powered 2 port unmanaged switch as it has 1 input which accepts the PoE power and 2 outputs which extends the PoE power to up to 2 PoE powered networkable devices such as IP cameras.
80mm PSE2 OUT
76mm
Performance Characteristics Complies with IEEE802.3, IEE802.3u , IEEE802.3ab, IEEE802.3af , IEEE802.3at standard Plug and play, no need to set. Data transmission speed rate : 10/100Mbps PD mode (power pins ) can comply both with 1/2+,3,6- (End-span ) & 4/5+, 7/8- (Mid-span ) Excellent circuit isolation. Mean Time Between Failures( MTBF ) : 30000h Transmission signal channel surge protect 1KV standard : IEC61000-4-5 Small Footprint
PSE1 OUT
D
PSE1 OUT
PSE2 OUT
A
B
E
C
A.PD Input Rj45 port
B . POE extender working Status Light
C.PSE Output Rj45 port E.Networt port working status
D . POE woking Status Light
PoE splitter cable installation instruction
Product internal design description Indicator PD RUN
PoE RUN
Installation guide
Description
Status ON OFF Blink ON OFF Blink
PD working normal
Please use the assorted equipments to install
Incorrect PSE device connection PD overload PoE output normal Not connected PD or Power supply type are not matched
Installation PoE extender is used with power supply unit and PoE device, can used in the network environment without the power supply cord or away from the power outlet , it can supply power for AP, IP camera , VoIP and other network devices.
Connected PD overload or undetected standard PD
Please link the PoE splitter correctly in the following steps: 1).Using UTP Cat5 cable to connect PoE port access of the power supply device(such as PoE switch) to PD IN port of this PoE extender. 2).Using UTP Cat5 cable to connect PoE OUT port of the PoE extender with PD.
Remark: Please Confirm that the PD complies with IEEE802.3af/at standard PoE Inidcators: Device has indicator lights showing if it is attached to a compatible PoE powered type of device.
Attention: 1).The Ethernet device connected with PoE extender shall not exceed maximum power of the PoE extender. 2).Even if the supply of power is enough, the same communication connected with PoE extender also must not exceed 3-level.
PoE IN cable: Please use UTP Cat5 or above to connect with PSE or PD. PoE OUT cable: Please use UTP Cat5 or above to connect with Ethernet device.
Confirm before installation: 1.Whether the power supply of PoE port is in line with the access equipment power demand or not. 2.Whether PoE standard requirement and power supply match with the PD of access (mid span/end span) or not.
Solution diagram
Product model and parameter description Po
IPCP-EXT2P: 10/100Mbps PoE extender , its front-end is powered , and its back-end is PSE , E
Sw
i tc
IEEE802.3af,15.4W, extending 100m
h
Port Description : PD input RJ45, PSE output RJ45
N RU PD
nd te Ex EPo
te
nd
er
PD
IN
er
Ex
Network Protocols: IEEE 802.3i; IEEE 802.3u; IEEE 802.3x Flow Control; IEEE 802.1af DTE Power via MDI
ow
er W
T PS
P
LI
N
K
er
Ex
nd
er
he
Et
T
OU E2 PS
N RU E
T OU
IN
Po
IN
N RU
r
i re
les
Ex EPo T
T
OU
Ex
te
nd
er
PC
am
Operating temperature : 0 to 55° C
PS
N RU
IN
T OU E1
Po er
a
PoE Type : PoE front PD input support End-span & Mid-span , PSE port only support
Product Size & Weight : 80mm*76mm*25mm(L*W*H), 0.15kg
et
rn
he
Et
E Po
er
s
EI
rk
r ov
Da 10 ta+ 0 M Po w Po
wo
we
Po
E2
OU
er
PD
de
Po
EW
PoE Standard : IEEE802.3af (port power : 15.4W), IEEE802.3at ( port power : 25.5W). et
IN
PD
en
er
xt
nd
EE
te
Po
PS
Da 10 ta+ 0 M Po w
Po
aN
PoE Cable core: 1/2+, 3/6Electromagnetic Emission(EME) : CE mark, commercial , FCC part 15 Class B RoHS.
E1
r
re
r ov
PS
we
eA
End-span or Mid-span .
et
rn
nd te Ex EPo
te
id
we
Po
T
OU
er
PD
IN
PD
RU
N
IN
PS
E1
OU
T
IN
Po
E
RU
N
U
Da 10 ta+ 0 M Po
PoE port : PoE IN PD (25.5W) , PoE Out PSE (15.4W )
et
rn
he
Et
r ov
we
Po
T
OU
er
Network Media : 100BASE-TX: UTP Cat5 , 100m or less
E2
OU
D 10 ata 0M +P
IN
Po IP E E CP xt -E end XT 2P er
EI
PC
am
er
a
EE
xt
en
de
r
Storage temperature : -20 to 70°C Working humidity : 10%～90% (no condensation ) Storage humidity: 5% 90% (no condensation )
er
