Transcript
Gio 5 Installation Guide for J Series
Copyright © 2004-2013 VXL Instruments Limited. All Rights Reserved. Information in this document is subject to change without prior notice and does not represent a commitment on the part of the manufacturer. No part of this guide may be reproduced or transmitted in any form or means, electronic or mechanical, including photocopying and recording, for any purpose, without the express written permission of the manufacturer. Registered trademarks are properties of their respective owners. Every effort has been made to make this guide as complete and as accurate as possible, but no warranty of fitness is implied. The authors and the publisher shall have neither responsibility nor liability to any person or entity with respect to loss or damages arising from the use of information contained in this guide. Last Updated: October, 2013 Version: GIO5/IG-40-13
VXL Instruments Ltd., House of Excellence, No. 17, Electronics City, Hosur Road, Bangalore– 560100, INDIA. www.vxl.net
Installing Gio 5 Several VXL Instruments thin client models come pre-installed with the Gio 5 operating system. To install the Gio 5 operating system on a J-Series thin client, follow the instructions provided in this Installation Guide.
Prerequisites •
A USB flash/pen drive with a capacity of 2 GB or above.
•
Windows7 or Windows7 2008R2 PC/Client (for USB flash/pen drive preparation).
•
J series Hardware.
•
A Gio 5 installation .ISO file.
•
Gio imaging Tool (Executable on Windows7 or Windows7 2008R2 PC/Client). Note: For hardware and installation binaries please contact VXL Instruments Ltd.
Configuring an USB Flash Drive as a Gio 5 Bootable Device To configure an USB flash / pen drive as a GIO 5 Bootable Device, as a prerequisite log into a system with administrative privilege and run the Gio Imaging Tool (GIO IT.exe). The Installation Wizard appears.
Browse and locate the destination folder click Next.
Installing Gio 5
1
Once the installation is complete the Gio IT shortcut is created on the desktop. To configure an USB key as a Gio 5 Bootable Device: 1. Double-click the Gio IT shortcut, The Gio Imaging Tool window appears.
2.
2
Browse and select the image file (.iso).
Installing Gio 5
3. Select the flash drive to be configured as a Gio 5 bootable device.
4. Click Create Disk. The following warning appears.
5. Click Yes. The flash drive is formatted.
The disk creation process starts.
Installing Gio 5
3
6. Once the process is complete, remove the USB key and close the Gio IT tool.
The USB flash drive is configured as a GIO 5 bootable device. Note: •
Do not remove the USB flash drive during the process.
•
The background process will exist on forcible exit.
•
The maximum time taken to configure an USB flash drive as a bootable device is 5 min.
I
4
Installing Gio 5
Installation Note: The installation procedure will take around 25 minutes. To install Gio 5 on your thin client from your Gio 5 bootable USB flash drive: 1. Insert the Gio 5 bootable USB flash drive in the USB port of your thin client. 2. Switch on the thin client. The VXL logo appears and the monitor screen goes blank. Wait for 90 to 100 seconds.
. 3. The Gio 5 installer appears. Note: Press the tab key to select options.
Installing Gio 5
5
4. From the Language option drop-down list, select a system language.
5. From the Time Zone drop-down list, select your time zone.
6
Installing Gio 5
6. From the Keyboard Type drop-down list, select your preferred input keyboard type.
7. Click Install. The Gio 5 installation Welcome screen appears. The installation progress bar indicates the progress of the Gio 5 installation.
Once the installation process is complete, the following message appears.
8. Press any key. The Thin Client shuts down. 9. Remove the USB key and turn on the Thin Client. Installing Gio 5
7
Once the thin client restarts, the Gio 5 operating system welcome screen appears.
For information about using the Gio 5 operating system, refer to Gio 5 user Manual for J series.
8
Installing Gio 5
