Preview only show first 10 pages with watermark. For full document please download

Similar Pages

   EMBED


Share

Transcript

» KTC5520/EATX Quick Reference Sheet « EATX 12V EATX POWER Serial Serial DDR 3 ECC Registered Channel 2 Slot 0 Fill First DDR 3 ECC Registered Channel 2 Slot 1 Fill Second DDR 3 ECC Registered Channel 1 Slot 0 Fill First Mem1 Fan EATX 12V CPU0 Fan DDR 3 ECC Registered Channel 1 Slot 1 Fill Second VGA DDR 3 ECC Registered Channel 0 Slot 0 Fill First DDR 3 ECC Registered Channel 0 Slot 1 Fill Second CPU 0 PS2 kbd mouse VGA RJ45 LAN2 USB Keyboard RJ45 LAN1 USB Mouse CPU1 Fan CPU 1 DDR 3 ECC Registered Channel 0 Slot 1 Fill Second DDR 3 ECC Registered Channel 0 Slot 0 USB RJ45 LAN 2 Audio Fill First DDR 3 ECC Registered Channel 1 Slot 1 Fill Second DDR 3 ECC Registered Channel 1 Slot 0 Fill First DDR 3 ECC Registered Channel 2 Slot 1 Fill Second USB Mic In RJ45 LAN1 Front Side Rear Sys3 Fan DDR 3 ECC Registered Channel 2 Slot 0 Slot 6 PCI Express Gen2 x8 5V LED Slot 5 PCI Express Gen2 x8 S/PDIF In Line Super I/O S/PDIF Out Center/LFE AST2050 Hearthbeat LED AST 2050 i82576 Slot 4 PCI Express Gen2 x8 i5520 5 4 SYS_ID_SW GND Reset SW PWR SW GND HDD LED - HDD LED + NIC#2 LED NMI_CPU_SW (Not Used) in out PWR LED - in out PWR LED + in out JP1 (7-8) Firmware Write Protect Protected Not Protected 3 JP2 JP1 1 1 2 SATA 1 AUX Connector POST Codes 0 Intrusion Connector - Enter in the BIOS Setup Menu. - Go to LAN Configuration Menu. This menu is located under «System Management» - Set LAN channel IP Address source, IP Address, MAC Address, Subnet Mask and if required the Gateway Address on the corresponding menu. Accessing Kontron Web Management Interface JP2 (9-10) Clear CMOS in Flash Clear CMOS in Flash Normal Operation 1 Sys2 Sys1 Fan Fan TPM Header Software Startup JP2 (1-2) BMC Disabled Disable BMC Operation Normal Operation USB / USB Flash Obtaining / Configuring the IP address: NIC#2 LED + SMBus SCL(Not Used) Chassis Intrusion SMBus SDA(Not Used) NIC#1 LED - NIC#1 LED + Front Panel Connector SYS Fault LED2 - in out SYS Fault LED1 - Disabled (No KVM function) Normal Operation SYS ID LED + SYS ID LED - JP3 (7-8) Onboard Video Speaker ICH10 JP3 FWM MEZZ Front Panel Power 1 Mem0 Fan IOH Slot 2 PCI Express Gen1 x4 USB ( Default Setting) Battery Slot 3 PCI Express Gen2 x8 Slot 1 PCI 32b / 33MHz JUMPER SETTINGS Fill First - Type the IPaddress of your board in the address bar of an Internet browser. - User Name: admin - Password: admin LEDs Significations 5V LED (Amber) On Off : 5V power is present onboard : 5V power is not present AST2050 Hearthbeat LED (Amber) Blink Off : Management Controller is working : Management Controller is not working RJ45 Connectors LED Link/Act OFF: No Link Green: Link Blinking: Activity Software Update Kontron recommands updating all onboard softwares for proper operation. Failing this operation might result in board misoperation. Visit www.kontron.com for all packages. www.kontron.com Speed OFF: 10Mb/s Amber: 100Mb/s Green: 1000Mb/s 1030-4773 V1.7 November 2010