Transcript
I-AB-105A
IMPORTANT INSTRUCTIONS http://www.sunnen.com
FOR USING SUNNEN PLATEAU HONING TOOLS on SUNNEN® MPS HONE HEAD MODULES
TWO TEETH .275in (7mm)
INSTALLATION: Because the height of the PHT Brush Assemblies is greater than Stone Assemblies, normally used with this tool; it is necessary to extend each Guide Master Holder away from the Hone Body. • Extend Guide Master Holder a distance corresponding to two (2) rack teeth, prior to inserting Pinion into Hone Body (approximately .275 in. / 7 mm). OPERATING TIPS: When Hone Head is placed into workpiece and expanded, there will be approximately 0.1 in. (2,5 mm) clearance between bore and guides when brushes first touch bore.
CAUTION: Excessive-honing pressure will crush brushes. Limit feed pressure, applying only enough force to stabilize tool in workpiece and produce slight filament deflection. Unlike a honing stone, increasing feed pressure will not significantly increase material removal rate. • When tool is expanded under appropriate brushing pressure, at least one guide must be loose. • When brush wear causes guides to bear against workpiece with full honing pressure, guides must be reduced in height. Ideally, tool should operate with very slight clearance, so guides only experience a small fraction of the force applied to brushes. “SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN PRODUCTS COMPANY.”
7910 Manchester Road • St. Louis, MO 63143 U.S.A. • Ph: 314-781-2100 • Fax: 314-781-2268 U.S.A. Toll-Free Sales and Service – Auto: 1-800-772-2878 • Ind: 1-800-325-3670 International Division Fax: 314-781-6128 ©COPYRIGHT SUNNEN® PRODUCTS COMPANY 2006, ALL RIGHTS RESERVED
0608
0608
Sunnen® reserves the right to change or revise specifications and product design in connection with any feature of our products contained herein. Such changes do not entitle the buyer to corresponding changes, improvements, additions, or replacements for equipment, supplies or accessories previously sold. Information contained herein is considered to be accurate based on available information at the time of printing. Should any discrepancy of information arise, Sunnen recommends that user verify the discrepancy with Sunnen before proceeding.
PRINTED IN U.S.A.
SUNNEN PRODUCTS COMPANY
PRINTED IN U.S.A.
Sunnen® reserves the right to change or revise specifications and product design in connection with any feature of our products contained herein. Such changes do not entitle the buyer to corresponding changes, improvements, additions, or replacements for equipment, supplies or accessories previously sold. Information contained herein is considered to be accurate based on available information at the time of printing. Should any discrepancy of information arise, Sunnen recommends that user verify the discrepancy with Sunnen before proceeding.
©COPYRIGHT SUNNEN® PRODUCTS COMPANY 2006, ALL RIGHTS RESERVED
International Division Fax: 314-781-6128
7910 Manchester Road • St. Louis, MO 63143 U.S.A. • Ph: 314-781-2100 • Fax: 314-781-2268 U.S.A. Toll-Free Sales and Service – Auto: 1-800-772-2878 • Ind: 1-800-325-3670
SUNNEN PRODUCTS COMPANY
“SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN PRODUCTS COMPANY.”
• When brush wear causes guides to bear against workpiece with full honing pressure, guides must be reduced in height. Ideally, tool should operate with very slight clearance, so guides only experience a small fraction of the force applied to brushes. • When tool is expanded under appropriate brushing pressure, at least one guide must be loose. CAUTION: Excessive-honing pressure will crush brushes. Limit feed pressure, applying only enough force to stabilize tool in workpiece and produce slight filament deflection. Unlike a honing stone, increasing feed pressure will not significantly increase material removal rate. OPERATING TIPS: When Hone Head is placed into workpiece and expanded, there will be approximately 0.1 in. (2,5 mm) clearance between bore and guides when brushes first touch bore. TWO TEETH .275in (7mm)
http://www.sunnen.com
INSTALLATION: Because the height of the PHT Brush Assemblies is greater than Stone Assemblies, normally used with this tool; it is necessary to extend each Guide Master Holder away from the Hone Body. • Extend Guide Master Holder a distance corresponding to two (2) rack teeth, prior to inserting Pinion into Hone Body (approximately .275 in. / 7 mm).
FOR USING SUNNEN PLATEAU HONING TOOLS on SUNNEN® MPS HONE HEAD MODULES
IMPORTANT INSTRUCTIONS I-AB-105A
