Transcript
DTV-7 Section II
Parts and Service Manual Order Parts Here:
www.ivie-ent.com/parts Ph:(918)254-5161
(Form. No. 78421B)
CLARKE TECHNOLOGY Operator's Manual DTV, STV & PTV
Page -17-
MAINTENANCE This section describes the procedure that must be done by a person authorized to do maintenance. WARNING:
Good A
Uneven
Small Holes
Good B High Mica
Good
Figure 1
WARNING:
Coloración desigual
Pequeños agujeros Bueno B
Demasiado pico
Bueno
C
Figure 2
Coloration inégale
Petits trous
Bon B
Bon A
Electrical inspections must be made by a person authorized to do maintenance. Electrical repairs must be made by a person authorized to make electrical repairs.
How to Check the Commutator and Carbon Brushes To check the commutator and the carbon brushes, follow this procedure: 1. Remove the screw that holds the motor cover. 2. Disconnect the wires. 3. Push the motor through the bottom of the plate. 4. Inspect the commutator. Take the machine to a Clarke authorized repair location if you see any of the following conditions: a. Small holes in th surface of the commutator. See figure 1A. b. Uneven color. Look for an even dark brown color. Clean areas indicate a problem. See figure 1B. c. High mica. The mica insulation must be lower than the commutator bars. See figure 1C. 5. Remove the carbon brush assemblies and check the carbon brushes. Replace both carbon brush assemblies if either of the carbon brushes is shorter than ½ inch (13mm), order two new brushes and replace both carbon brushes earlier than the normal inspection time. 6. Install the motor cover, and the fasteners. WARNING:
Trop de Mica
Bon
Keep the machine clean. It will have longer life and need fewer repairs. Maintenance of the Motor The motor that has a commutator and carbon brushes must be checked every six months or 600 hours or operation.
C
Bueno A
To prevent electrical shock, always remove the electrical plug from the electrical outlet before doing any repairs or maintenance to this machine.
The machine must be tested for electrical safety after electrical repairs are made.
NOTE: For best operation, have the machine checked by a Clarke authorized repair person every 12 months. C
Figure 3 Page -18-
For safe operation and longer life of your product, use Clarke parts. CLARKE TECHNOLOGY Operator's Manual DTV, STV & PTV
CLARKE TECHNOLOGY DTV-7 Head Assembly Drawing & Parts List 12/98
1
2 3 4 56 7
8
9 10 11 12 27 28 29
13 14 15 16
17 18 19 20 21 22 23 24 25 26 30
Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Part No. 51841A 56448A 54503A 56441A 50522A 51842A 56481A 54914A 56482A 56482A 52957A 47316B 56441A 57162A 56482A 51844A 54063A 56483A 56484A 54340A 59859A 56485A 56035B 56047B 40834A 40835A 24 54377A 25 53984A 26 50521A 27 57377A 28 964006 29 924007 30u 54340A NI 59887A NI 52944A
Description Power Cord Strain Relief Grip, Cord Screw 5mm x 20mm Block Terminal Hook, Cord Screw, 5mm x 30mm Handle, Lift Screw, 5mm x 35 mm Screw, 5mm x 35 mm Cover, Dome Switch, Rocker Screw, 5mm x 20mm Plug, Upper Screw, 5mm x 35mm Cover, Motor Filter, Motor Screw, 5mm x 40mm Support, Motor Gasket, Head Assembly Washer, Star Screw, 4mm x 8mm Motor, Vac 115V Motor, Vac 230V Brush, Carbon 115V Brush, Carbon 230V Gasket, Vac Motor Filter, Motor Base Base, Motor Receptacle, Accessory Screw, 3mm x 16 mm Nut, 3mm Gasket, Head Wire, Connect Clip
Qty 1 1 1 2 1 1 4 1 2 2 1 1 4 1 6 1 1 6 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 4 3
NI = Not illustrated NOTE: u indicates a change has been made since last publication of this manual.
Page -20-
CLARKE TECHNOLOGY Operator's Manual DTV, STV & PTV
CLARKE TECHNOLOGY DTV-7 Filter Bag Assembly Drawing & Parts List 12/97 1 2
Ref. 1 2 3 4 5 6
3 4 5
Part No. 53970A 51822A 56482A 57842A 50763A 58417A
Description Filter, Intake Cage, Float Screw, 5mm x 35mm Ring, Support Filter Base Bag, Filter Support, Bag
To add optional HEPA 54016A HEPA Filter 1 51884A Float Cage 1 57372A Retainer 1
6
Filter for 58541A 58411A 34294A
Qty 1 1 4 1 1 1
DTV-7 order: Spacer, Plastic Screw, 5 x 25 Gasket, Cage
4 4 1
Tank Assembly Drawing & Parts List
1
2
3
4
5
6 7
Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13
8
5
Part No. 51823A 57376A 58921A 56481A 57375A 54376A 53133A 50336A 50524A 58692A 50526A 52128A 56489A
Description Clamp, Tank Rivet Tank, Poly 7 Gallon Screw, 5mm x 35mm Retainer, Poly Tank Gasket, Tank Deflector, Tank Adaptor, Hose Button, Push Spring, Pushbutton Bumper, Tank Caster, Swivel Screw, 4mm x 15mm
Qty 2 4 1 4 1 1 1 1 1 1 1 4 16
9 10 11 12 13
DTV-7 Dry Vac Tools
Part. No. 39710A 39709A 35183A 39207A 39206A 39205A 39204A
Description Wand, Curved Wand, Chrome Hose, Flexible Tool, Carpet/Floor Tool, Crevice Tool, Dusting Tool, Upholstery
CLARKE TECHNOLOGY Operator's Manual DTV, STV & PTV
Page -21-
