Transcript
MARKETIER 18 GAUGE SHELVING UNITS
JOB NAME: ___________________________ ITEM NO.: ____________________________ NO. REQUIRED: _______________________
DESCRIPTION: Shall be Market Forge Marketier Shelving Type Number ____________. SOLID - Stainless Steel Flat Surface □ Model MSF LOUVERED - Stainless Steel 3/8” (310mm) Louvers with 2” (51mm) Embossments □ Model MSL
SHELVES: Each shelf shall be made of solid heavy duty 18 gauge material with all four corners uniformly coped to exact contour to receive internal corner castings in crevice-free alignment. The perimeter of each shelf shall have a die-formed raised marine edge, (3mm) high on a (7mm) radius. The lower edge of the shelf perimeter shall be hemmed and pressed tight along the shelf length. Shelves shall be shipped with set screws for each corner to allow shelves to be installed or adjusted at any desired spacing. Shelf corner castings have a hole to take 1” O.D. shelf posts. Shelves shall be available as required in any combination of the following widths and lengths as designed or as shown on plans. Shelves shall be ____ tier high (3 to 8) or as shown. WIDTHS:
30” (762mm)
14” (356mm)
36” (914mm)
18” (457mm)
42” (1097mm)
20” (508mm)
48” (1219mm)
24” (610mm)
54” (1372mm) 60” (1524mm) NOTE: The Following sizes shall be constructed with a reinforcing bar in the length dimensions for extra security against sagging under exceptionally heavy loads: □ 18” x 60” □ 20” x 60” □ 24” x 54” □ 24” x 60”
Available in the following: □ Stainless steel Available in the following lengths: □ 63” (1600mm) □ 78” (1981mm) Special length posts are available upon request. In installations where multiple corner sections are required, removable and adjustable clips shall be provided (optional at extra cost) to rigidly support adjacent shelves (eliminating the need for corner posts). In multiple sections, one section only shall require four posts and all adjacent sections two posts with two supporting clips per shelf. Shelves shall be delivered knocked down and packed in protective cardboard containers marked with the size and material of the contents. OPTIONAL AT EXTRA COST: □ Double Fold & Flatten Reinforcement provide security against sagging under exceptionally heavy loads. □ Adjustable flanged feet □ Adjustable wall brackets for fastening rear posts to wall. □ Dividers (Front-to-Back) □ Back Ledges □ End Ledges □ Label Holders □ Shelf Clips
FOOD SERVICE EQUIPMENT Marketier Shelving
LENGTHS:
POSTS: Shall be provided with press fit plastic caps at both top and swivel casters for the base. Posts shall be marked at 2” intervals to assist alignment of shelves during assembly.
SPEC SHEET: R-1533J 03/11
EMBOSSED - Stainless Steel 2” (51mm) Embossments with 2” (51mm) Flat Spaces □ Model MSE
The manufacturer reserves the right to modify materials and specifications without notice.
PRINTED IN U. S. A. 35 Garvey Street • Everett • MA • 02149 Tel: (617) 387-47100 • Toll Free: (866) 698-3188 • Fax: (617) 387-4456 • Outside MA Fax: (800) 227-2659 E-Mail:
[email protected] • Website: w w w . m f i i . c o m
MARKETIER 18 GAUGE SHELVING UNITS
DETAILS & DIMENSION
TYPES
MATERIAL
MODEL TYPE
Solid (Flat Surface)
Stainless Steel
MSF
Louvered (3/8” Louvers with 2” Embossments)
Stainless Steel
MSL
Embossed (2” Embossments with 2” Flat Spaces)
Stainless Steel
MSE
Marketier Shelving
FOOD SERVICE EQUIPMENT
SPEC SHEET: R-1533J 03/11
AVAILABLE TYPES OF SHELVING
This Product is ETL Complaint with ANSI/NSF-2 Standard.
35 Garvey Street • Everett • MA • 02149 Tel: (617) 387-47100 • Toll Free: (866) 698-3188 • Fax: (617) 387-4456 • Outside MA Fax: (800) 227-2659 E-Mail:
[email protected] • Website: w w w . m f i i . c o m
