Transcript
55mm
Installation instructions Installation instructions UNDER DESK MOUNT VERSION - Drill hole through desk in desired position. Mount Pole and components to desk, ensure that the cresent cut out in the base of the pole is facing the rear of the desk, and screw together tightly.
1 1
the desk pole in its are facing the bles to come out
UNDER DESK MOUNT VERSION - Drill hole through desk in desiredCLAMP position. Mount Pole and the components to desk, DESK VERSION -Fasten desk clamp to theensure back that the cresent out inyou the place base of pole sheet is facing the the rear edge of the desk.cut Ensure thethe rubber under of theclamp desk, so and desk asscrew not totogether damagetightly. the desk surface.
2 3
Power and Video Cables
Threaded Stud Inserts
600mm
A
Pole Rubber sheet
600mm
B
Cable Guide
Long Arm Pin
Long Arm Pin
Pole
Cable Guide
DESK CLAMP VER edge of the desk. desk clamp so as n
3
Power and Video Cables
Cable Exit facing the front Cable Exit facing the front
r sheet
0mm
1 2
Pole
Desk Clamp
Under desk mount Desk Clamp
Under desk mount
ed Stud Inserts
rough desk in desk, ensure facing the rear
Rubber sheet
Installation instructions
Pole
Ellipta Arm
Pole
55mm
Rubber sheet Rubber sheet
Under desk mount Desk Clamp
Cast Sw Cast Swivel joint
Desk Clamp
Fastenin
To computer and power Fastening bolt
To computer and power
LCD Monitor
UNDER DESK MOUNT VERSION - Drill hole through desk in desired position.VERSION Mount Pole and components to desk, DESK CLAMP -Fasten the desk clamp to theensure back that the cutEnsure out in you the base therubber pole issheet facing the rear edge ofcresent the desk. placeofthe under the of the clamp desk, and together desk so asscrew not to damagetightly. the desk surface.
2 3
Power and Video Cables
A
Cable Exit facing the front
600mm
B
Cable Guide
DESK CLAMP VERSION -Fasten the desk clamp to the back edge the desk. Ensure the rubber sheet underpole the in Placeof Cable guide, poweryou andplace video cables into the desk desk clampshown so as above. not to damage the the deskcable surface. the order Ensure that exits are facing the front of the desk as shown above. Also allow cables to come out of the pole 600mm, as shown above.
3 4
A
B
Long Arm Pin
Place Cable guide, power and video cables into the desk pole in order shown above. Ensure that the cable exits are facing the Athe - Attach Cast swivel Joint to Ellipta Arm. of the desk as shown above.on Also cables to come out Bfront - Place LCD Screen face down theallow desk and screw monitor of the 600mm, shownwith above. arm to pole the back of theasscreen the screws provided. Ensure that the screws are fastened tightly.
A - Attach Cast sw B - Place LCD Scr arm to the back of that the screws are
4 5
5 Cable Clip
Long Arm Pin
Cable Clip
Ellipta Arm
Pole
Ellipta Arm
Cast Swivel joint Cast Swivel joint Fastening bolt
To computer and power Fastening bolt
LCD Monitor LCD Monitor
Place Cable guide, power and video cables into the desk pole in the above.Joint Ensure that the cable exits are facing the A - order Attachshown Cast swivel to Ellipta Arm. front of theLCD deskScreen as shown Also to come out B - Place faceabove. down on theallow deskcables and screw monitor of thetopole 600mm, as screen shown with above. arm the back of the the screws provided. Ensure that the screws are fastened tightly.
4 5
A - Attach Cast swivel Joint to Ellipta Arm. BLower - Place LCDArm Screen on attached the desk and monitor Ellipta withface LCDdown monitor ontoscrew the table arm to thepole. backOnce of thethe screen screws provided. Ensure mounted Arm with is in the position thread the cables that the screws areclip fastened tightly. through the cable and then plug into the back of the screen.
5 Cable Clip
Lower Ellipta Arm with LCD monitor attached onto the table mounted pole. Once the Arm is inWeight. position-thread the Arm cables Adjusting Spring to suit Screen Once the is through the cable then into back of the spring screen. fully assembled youclip mayand need to plug adjust thethe tension with the Hafele Key enclosed. Turn key in clockwise direction until screen is supported by the spring.
Adjusting Spring fully assembled you with the Hafele Key screen is supported
