Transcript
/. UN/VERSA L REMOTE
.
OWNER’S MANUAL ELJR95
I
1 .Lift up on the battery compartment cover tab compartment and remove the battery cover. 2. Install four (4) ‘MA” batteries, paying attention to the polarity diagram in the battery compartment. 3. Replace the battery compartment cover. NOTE: When batteries are removed, this remote will retain the setting (code) for approximately 15 minutes. Should you fail to replace the batteries within 15 minutes, use the tip of a pen to reset the unit. The RESET button is located in the battery compartment.
RESET SWITCH
/.,:$ flboresceni lamp & any”oth& ‘strotig ..ligt “‘1:: shines &i &e REMOTE SENSOR of the upi the remote operation .may be ‘iinstable. ;.” ,%.‘. :. ‘. :1. _;: ‘. ‘. ’ . : _’ . ’ . . .‘_. _;
-SEmlNG UP THE UNIVERSAL REMOTE CONTROL
1 e Locate the two (2) digit number corresponding to your TV, VCWVCP or Combo’s model number located on page 2. 2. Simultaneously press and hold the CALL and ENTER buttons together until the status indicator lights. (The status indicator is located on the top right on the front of the remote.) 3. Using the number buttons, enter the two (2) digit code. L 4. The Status indicator should go out immediately. If the Status indicator slowly blinks twice, a wrong device code has beer entered. In this case, repeat the procedure. OPERATING THE UNIVERSAL REMOTE CONTROL
Once the Universal Remote Control code has been set, it works just like the original remote. Just aim the Universal Remote Control at the TV, VCWVCP or Combo and press the desired button(s). FINDING THE LOCATION OF CONTROLS FOR YOUR TV/VClUVCP/COMBO
For detailed descriptions of the functions available from the Universal Remote Control, locate the model number of the TV, VCWVCP or Combo on page 2 and then turn to the page indicated. Each Location Of Controls consists of an illustration of the Universal Remote Control and a description of each button that can be used with the TV, VClWCP or Combo. If a button is labelled and is shaded black, then it can be used with the TV, VCRNCP or Combo. If a button is not labelled and is not shaded, then it cannot be used with the TV, VCR/VW or Combo.
1
MODEL NO. HTS2960D
CODE NO. 20
LOC PAGE 23
MODEL NO. TC2555DA
CODE NO.
LOC PAGE
00
3
16
19
HTS2960DG
20
23
TC2555DA, Suffix B
HTS3075D
20
23
TC2556D
02
5
TC2556DA
10
13
TC0918
02
5
TCI 351
23
26
TC2556DB
10
13
TC4253
30
33
TC1353
10
13
TCI 365
00
3
TC4352
30
33
27
30
TS1996
27
30
TCl365B
16
19
TS1997
10
13
TC1369
27
30
TSI 997A
IO
13
TCI 372
23
26
TS2041 D
00
3
22
TS2042D
00
3
TC1366
TCI 375
19
TC1375A
IO
13
TS2585D
00
3
TC1379/C
27
30
TS2586D
00
3
TC19650
00
3
TS2587D
02
5
TC19660
19
TS2587DA
10
13
TCl972A
16 s IO
13
TS2587DB
10
13
TCI 9720
02
5
TS2760D
20
23
TC1972DA
10
13
TS2761 D
15
18
TC1972DB
10
13
TS2762D
17
20
TCI 994
23
26
TS3050D
21
24
TC202OD
16
19
TS3050DN
20
23
TC2555D
00
3
CODE NO.
LOC PAGE
CODE NO.
LOC PAGE
MODEL NO.
’
VCP680
06
9
MODEL NO. VR4250
24
27
1 VCP681
05
8
VR4450
24
27
1 VCP682
05
8
VR4546
25
28
~ VCPR200
22
25
vi-0952
18
21
VCR767
03
6
V-l-0954
09
12
~ VCR968
07
10
VT0954A
28
31
VCR1 500
12
15
VT0955
09
12
VCR1 795
14
17
VT0955A
28
31
VCR1 795A
03
6
VT1315
26
29
VCR1 795s
08
11
VT1 315A
26
29
VCR2000
03
6
W-1321
04
7
VCR3000
08
11
VT1 322
01
4
VCR3001
13
16
VT1 322A
28
31
VCR3002
12
15
VT1 355/A
28
31
VCR3003
12
15
VT1921
04
7
VCR3003A
29
32
VT1 922
01
4
VCR4000
07
10
VT1922A
28
31
I VCR4002 ‘I VCR4003
11
14
VT1 975/A
28
31
14
VT2522D
01
4
VCR4003A
29
32
VT2522Da/B
28
31
vcs990
07
10
11
-
2
I
#
l-
16
2
1.
POWER Button - Press to turn the TV on and off.
2.
Direct Channel Selection Buttons - Press to select any channel.
3m
AUTO Button - Used with the CH SET button to set channels into
memory. - 15
34
14 -13 12
5T -I---
4.
- 11
50 60 7.
10 -9
8. 90
CH. SET Button - Press to set TV channels into memory. ADD Button - Press to add a channel into memory. DELETE Button - Press to delete a channel from memory. TIME SET Button - Press to set the Timer. TIMER SEL. - Press to select the timer function to be set. SELECT Button - Press to select the on-screen picture
adjustments. 10. MUTE/RESET Button - Press to instantly turn off the sound or to 8 11 0 12. 13a
160
CODE NO: 00
reset the on-screen picture adjustments. VOL v /Min. Button - Press to lower the volume level, set the Minute or set picture adjustments. CHANNEL A and v Buttons - Press to select a channel. VOL A /Hour+ Button - Press to raise the volume level, to set the Hour or set picture adjustments. RECALL Button - Press to display the channel and time on the TV screen. Q. VIEW Button - Press to switch between the last channel viewed and the present channel. SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes
POWER Button - Press to turn the TV/VCR on and off. Direct Channel Selection Buttons - Press to select any channel. RESET Button - Press to reset the Linear Time Tape Counter to
1a 2. 3.
2
“OHOOMOOS”. 40
MEMORY Button - Used to stop the tape when the counter
50
AUTO Button - Used with the CH SET button to set channels into
reaches “0H00M00S”. 6
memory.
8 ! . L
CH. SET Button - Press to set channels into memory. CH 112 Button - Switches between Channel 1 and Channel 2 in
6. 90
10 12
80
14
9. 100
16 18
11 cl 120 \ 13 0 140 15a
CODE NO: 01 17m 18 . i. 19: 20 0 21 0 22 0 23 0 24 0 25 0 26 . 27m 28 0 29 0 30 0 31 D 9230 0 34a
16
q
the Closed-Caption mode. ADD Button - Press to add a channel into memory. DELETE Button - Press to delete a channel from memory. REPEAT Button - Press to set the TV/VCR to play back the tape over and over until stopped manually. CANCEL Button - Press to clear the selected timer recording program. CLK/PROGRAM Button - Press to bring up the menu screen for Timer Recording and Clock Setting. PROG. CONF Button - Press to confirm the programmed timer recording. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape.
PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen TRACKING A and v Buttons - Press to manually adjust the tracking. TRACKING AUTO Button - Press for automatic tracking. Tape SPEED Button - Press to select a recording tape speed (SP/LP/EP). REC/OTR Button - Press once for normal recording. Additional pressed activate Qne-Touch Timer Recording. TIMER REC Button - Press to set the VCR to start recording at a preset time. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape fowards. Press in the Play mode to J
activate Forward Search. ENTER Button - Press to enter information for timer recording and clock setting. SELECT Button - Selects on-screen picture adjustments. MUTE Button - Press to turn off the sound. Press again to turn the sound back on. TV/CAP/TEXT Button - Switches between Caption, Text and TV modes for Closed-Captioned programs. VOLUME Down (-) Button - Press to lower the volume level or on-screen picture adjustments. CHANNEL A/Set + and v /Set - Buttons - Press to select a channel or to set Timer Recording and clock. VOLUME Up (+) Button - Press to increase the volume level or on-screen picture adjustments, CALL Button - Press to display the present time/day of the week, channel and counter of the TV screen. Quick View Button - Press to switch between the present channel and the last chan,nel selected., SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes RESET Button - Press to reset the on-screen picture adjustments.
4
L
.
1
16
-15 14 -13 12 -14 10 -9 8
3 5 6
7
10
POWER Button - Press to turn the TV on and off.
2.
Direct Channel Selection Buttons - Press to select any channel.
3.
CH l/2 Button - Switches between Channel 1 and Channel 2 in the Closed-Caption mode. AUTO Button - Used with the CH SET button to set channels into memory. CH. SET Button - Press to set TV channels into memory. ADD Button - Press to add a channel into memory. DELETE Button - Press to delete a channel from memory. SELECT Button - Press to select the on-screen picture adjustments. MUTE/RESET Button - Press to instantly turn off the sound or to reset the on-screen picture adjustments. TV/CAP/TEXT Button - Switches between Caption, Text and W modes for Closed-Captioned programs. VOL v /(-) Button - Press to lower the volume level or set picture adjustments. CHANNEL A and v Buttons - Press to select a channel. VOL A /(+) Button - Press to raise the volume level or set picture adjustments. RECALL Button - Press to display the channel and time on the TV screen. Q. VIEW Button - Press to switch between the last channel viewed and the present channel. SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes
4a 5. 60 70 8s 9m 10. 11 . 120 13. 140 150
CODE NO: 02
16 0
NOTE: The CH1/2 (3) and the TV/CAP/TEXT (IO) buttons are not functional for model TC0918.
5
69 P I
e9
ou
I
1
32 -31
1. 2. 3.
POWER Button - Press to turn the TV/VCR on and off. Direct Channel Selection Buttons - Press to select any channel. RESET Button - Press to reset the Linear Time Tape Counter to
“0HO0M00S”. 4. 3
30 - 29 28 - 27 26
5
’
7 9
-25 24
11
2223
13
-21
2019
5. 6 7: 8. 9. 10m 11 .
18
12. 13 14:
15. 16.
CODE NO: 04 17
23D 240 25 26: 27. 28 29: 30D 31 0 32.
reaches “OHOOMOOS”. AUTO Button - Used with the CH SET button to set channels into memory. CH. SET Button - Press to set channels into memory. ADD Button - Press to add a channel into memory. DELETE Button - Press to delete a channel from memory. REPEAT Button - Press to set the TV/VCR to play back the tape over and over until stopped manually. CANCEL Button - Press to clear the selected timer recording program. CLK/PROGRAM Button - Press to bring up the menu screen for Timer Recording and Clock Setting. PROG. CONF Button - Press to confirm the programmed timer recording. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen
TRACKING A and v Buttons - Press to manually adjust the tracking.
18: TRACKING AUTO Button
19. 20. 21 0 22Q
MEMORY Button - Used to stop the tape when the counter
- Press for automatic tracking. Tape SPEED Button - Press to select a recording tape speed (SP/LP/EP). RECIOTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. TIMER REC Button - Press to set the VCR to start recording at a preset time. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to activate Forward Search. ENTER Button - Press to enter information for timer recording and clock setting. SELECT Button - Selects on-screen picture adjustments. MUTE Button - Press to turn off the sound. Press again to turn the sound back on. VOLUME Down (-) Button - Press to lower the volume level or on-screen picture adjustments. CHANNEL A/Set + and v /Set - Buttons - Press to select a channel or to set Timer Recording and clock VOLUME Up (+) Button - Press to increase the volume level or on-screen picture adjustments. CALL Button - Press to display the present time, channel and counter of the TV screen. Quick View Button - Press to switch between the present channel and the last channel selected. SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes. RESET Button - Press to reset the on-screen picture adjustments.
4
POWER Button - Press to turn the VCP on and off. REPEAT Button - Press to repeatedly play back the tape over
and over until the STOP button is pressed. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. TRACKING v Button - Press to manually adjust the tracking. TRACKING AUTO Button - Press for automatic tracking. TRACKING A Button - Press to manually adjust the tracking. EJECT Button - Press to eject a tape. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to activate Forward Search,
8
1.
POWER Button - Press to turn the VCP on and off.
2.
7a 8.
REPEAT Button - Press to repeatedly play back the tape over and over until the,STOP button is pressed. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen TRACKING v Button - Press to manually adjust the tracking. TRACKING AUTO Button - Press for automatic tracking.
9.
TRACKING A Button - Press to manually adjust the tracking.
3. 4.
5. 6a
w,
10
3 4 5 6 7 -8
100 F.FWD (Fast Forward) Button - Press in the Stop mode to
rapidly wind the tape forwards. Press in the Play mode to activate Forward Search.
9
:
CODE NO: 06
-29
3
POWER Button - Press to turn the VCR on and off. Direct Channel Selection Buttons - Press to select any channel. MEMORY Button - Used to stop the tape when the counter
reaches “0:OO:OO”. 28 - 27
3
1 6
26
5
- 25 24 -23
7 9
22 -21
11 13
2049 18
15
- 17
CODE NO: 07 .
VISS Button - Press to search for Index marks. TV MONI Button - Press to temporarily view a TV channel
selected on the UCR while in the playback mode. REPEAT Button - When pressed, the VCR will play back the tape over and over until stopped manually. PROGRAM Button - Press to select a program for timer recording. ENTER Button - Press to enter information for timer recording and clock setting. CLOCK/COUNTER Selector button - Press to cycle between the clock and the linear time tape counter. PROG. CONF Button - Press to confirm the programmed timer recording. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse .* Search. 93 STOP Button - Press to stop the tape. 14: PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. 15 0 TRACKING A and ‘I Buttons - Press to manually adjust the tracking.
46. TRACKING AUTO Button - Press for automatic tracking. 17. Slow Speed Up and Down Buttons - Press to speed up or slow down slow motion playback.
J
18. REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. 19- SPEED Button - Sets the tape speed for recording. 20. SLOW Button - Press in the Play mode to activate slow motion playback. Press in the Pause/Still mode to advance
one frame. 21 a TIMER REC Button - Press to set the VCR to start recording at a preset time. 22. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards Press in the Play mode to
activate Forward Search. 23, SET Up/Down Buttons - Press to set clock and timer recording. 24. SKIP SEARCH Button - Press once to switch from the playback mode to the forward search mode for 30 seconds. 25. CANCEL Button - Press to clear the selected timer recording program.
26. CHANNEL A and v Buttons - Press to select a channel. 27. RESET Button - Press to reset the Linear Time Tape Counter to “0:OO:OO”. Pam CLOCK Button - Press to reset the present time. ‘29. TV/VCR Button - Press to switch between TV and VCR.
1
1
25
1.
POWER Button - Press to turn the VCR on and off.
2.
Direct Channel Selection Buttons - Press to select any channel.
30
MEMORY Button - Used to stop the tape when the counter reaches “0:OO:OO”. VISS Button - Press to search for Index marks. REPEAT Button - When pressed, the VCR will play back the tape over and over until stopped manually. PROGRAM Button - Press to select a program for timer recording. ENTER Button - Press to enter information for timer recording and clock setting. CLOCK/COUNTER Selector button - Press to cycle between the clock and the linear time tape counter. PROG. CONF Button - Press to confirm the programmed timer recording. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. TRACKING A and 7 Buttons - Press to manually adjust the tracking. TRACKING AUTO Button - Press for automatic tracking.
2-
40 -24 23
3 4-
- 22 21
5 68 7 9 10 11 42 13 ,.I4 -15
-20 39 -18 17 -16
5. 60 7D 8m 90 10. 11 .
12. 13D 14.
CODE NO: 08
150
16. SPEED Button - Sets the tape speed for recording. 170 REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. 18m TIMER REC Button - Press to set the VCR to start recording at a preset time. m 19 200 21 . 22e 23. 240 25.
FFWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards Press in the Play mode to activate Forward Search. SET Up/Down Buttons - Press to set clock and timer recording. CANCEL Button - Press to clear the selected timer recording program. CHANNEL A and v Buttons - Press to select a channel. RESET Button - Press to reset the Linear Time Tape Counter to “0:OO:OO”. CLK SET Button - Press to reset the present time. TV/VCR Button - Press to switch between TV and VCR.
44
29
4
28
2-
4
1. 2.
POWER Button - Press to turn the TV/VCR on and off.
3.
MEMORY Button - Used to stop the tape when the counter reaches “0:OO:OO”. RESET Button - Press to reset the Linear Time Tape Counter to “0:00:00”. TV MONI. Button - Press to temporarily view a TV channel selected on the VCR while in the Play mode. CANCEL Button - Press to clear the selected timer recording program. MENU Button - Press to display the On-screen menu function. ENTER Button - Press to enter information for timer recording and clock setting. PROG. CONF Button - Press to confirm the programmed timer recording. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. TRACKING A and v Buttons - Press to manually adjust the tracking. TRACKING AUTO Button - Press for automatic tracking.
Direct Channel Selection Buttons - Press to select any channel.
4a 27 - 26 25 - 24 23
3
56 78 9 10 11 1213 l415
22 -21
5. 6. 7. 8.
20 =I8 36
9. 10. 11 . \ 12. 13. 14.
CODE NO: 09
15.
16 0 Tape SPEED Button - Press to select a recording tape speed (SP/LP/EP). 17 . REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. 18 0 TIMER REC Button - Press to set the VCR to start recording at a preset time.
J
? 20:19 EJECT Button - Press to eject a tape., F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape for\Mards. Press in the Play mode to activate Forward Search. 21 0 SET Up/Down Buttons - Press to set clock, timer recording, auto repeat and language. 22 0 MUTE Button - Press to turn off the sound. Press again to turn the sound back on. 23 0 VOLUME Down Button - Press to lower the volume level. 24D CHANNEL A and v Buttons - Press to select a channel. 25 VOLUME Up Button - Press to increase the volume level. 26: CALL Button - Press to display the present time/day of the week, channel and counter of the TV screen 27 0 Quick View Button - Press to switch between the present channel and the last channel selected. 28 t3 SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes I’1 29 m RESET Button - To reset the on-screen picture adjustment.
1%
d-
- 15 14
2
POWER Button - Press to turn the TV/VCR on and off.
2. 3.
Direct Channel Selection Buttons - Press to select any channel.
- 13
3-
I
1.
12
4.
- 11 1-o - 9
4 5-
8 -
5e 60
7
70 8Q 9. 10. i 11 . 12. 130
140
CODE NO: IO
150
CH l/2 Button - Switches between Channel 1 and Channel 2 in the Closed-Caption mode. TV/CAP/TEXT Button - Switches between Caption, Text and TV modes for Closed-Captioned programs. MENU Button - Press to display the on-screen function menu. ENTER Button - Press to enter information for on-screen operations. SET Up/Down Buttons - Press to set language, CH SET, Picture and/or Audio. MUTE Button - Press to turn off the sound. Press again to turn the sound back on. VOLUME Down Button - Press to lower the volume level. CHANNEL A and v Buttons - Press to select a channel. VOLUME Up Button - Press to increase the volume level. CALL Button - Press to display the channel number in the upper right corner of the TV screen. Quick View Button - Press to switch between the present channel and the last channel selected. ’ SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes. RESET Button - Press to reset the on-screen picture adjustments.
13
29
- 2 8
1.
POWER Button - Press to turn the VCR on and off.
2.
Direct Channel Selection Buttons - Press to select any channel.
3.
MEMORY Button - Used to stop the tape when the counter
4.
reaches “0:OO:OO”. VISS Button - Press to search for Index marks. CH. SKIP (Channel SKIP) Button - Used to skip over unwanted
5.
%?ChUldS.
27
6.
- 2 6 25
70
- 2 4
8. 9.
2322 2120
19
-18
10e $1 0 11 0 13 0
. . . . .#f .*0. ^.V. -
140 15 e
CODE NO: 11
TV MONI. Button - Press to temporarily view a W channel selected on the VCR while in the Play mode. CANCEL Button - Press to clear the selected timer recording program. MENU Button - Press to display the On-screen menu function ENTER Button - Press to enter information for timer recording and clock setting. CLOCK/COUNTER Selector button - Press to cycle between the clock and the linear time tape counter. PROG. CONF Button - Press to confirm the programmed timer recording. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and d’isplay a still picture on the TV screen.
17: 16 TRACKING A and v Buttons - Press to manually adjust the tracking. TRACKING AUTO Button - Press for automatic tracking. 18 #J Slow Speed Up and Down Buttons - Press to speed up or slow down slow motion playback.
J
20: 19 REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. Tape SPEED Button - Press to select a recording tape speed (SP/LP/EP). 21 e SLOW Button - Press in the Play mode to activate slow motion playback. Press in the Pause/Still mode to advance
one frame. 22a TIMER REC Button - Press to set the VCR to start recording at a preset time. as:23 EJECT Button - Press to eject a tape. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to 25 e 26 0 27 . I’1 28 a 29 .
activate Forward Search. SET Up/Down Buttons - Press to set clock, timer recording, auto repeat and language. SKIP Search Button - Press in the Play mode to search forward through approximately 30 seconds of tape. CHANNEL A and V Buttons - Press to select a channel. RESET Button - Press to reset the Linear Time Tape Counter to “0:OO:OO”. I TVA/CR Button - Press to switch between TV and VCR.
14
10
POWER Button - Press to turn the VCR on and off.
2.
Direct Channel Selection Buttons - Press to select any channel.
30
RESET Button - Press to reset the Linear Time Tape Counter to
“0:00:00”. 40
3
CANCEL Button - Press to clear the selected timer recording
program. 20
5.
MENU Button - Press to display the on-screen function menu
60
ENTER Button - Press to enter information for timer recording and clock setting. CLOCK/COUNTER Selector button - Press to cycle between the clock and the linear time tape counter. PROG. CONF Button - Press to confirm the programmed timer recording. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. TRACKING A and v Buttons - Press to manually adjust the tracking. TRACKING AUTO Button - Press for automatic tracking. SPEED Button - Sets the tape speed for recording.
4-
5 9
-19
89 IO 11 42 13 14 -
18 - 17 16 - 15
9. 8. 9. 10.
11 D 12. 130 140 15a
CODE NO: 12 16. REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. 17, TIMER REC Button - Press to set the VCR to start recording at a preset time. 18. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to
activate Forward Search. 19. SET Up/Down Buttons - Press to set clock, auto repeat, language and timer recording. 20. CHANNEL A and v Buttons - Press to select a channel. 21. TV/VCR Button - Press to switch between TV and VCR.
15
22
I
1.
POWER Button - Press to turn the VCR on and off.
2 eJ
Direct Channel Selection Buttons - Press to select any channel.
“0:00:00”. -21
3
20
4--19 18 -17 16 -15
program. 5
0
l
PROGRAM Button - Press to select a program for timer
recording.
7. a0 9. IO0
11 e 12 . _. r . ‘,2*’ . - ..,
130 14a
CODE NO: 13
CANCEL Button - Press to clear the selected timer recording
4.
60
5 9 89 loll 1213 14 -
.
RESET Button - Press to reset the Linear Time Tape Counter to
3.
2-
15 .
ENTER Button - Press to enter information for timer recording and clock setting. CLOCK/COUNTER Selector button - Press to cycle between the clock and the linear time tape counter. PROG. CONF Button - Press to confirm the programmed timer recording. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and .i display a still picture on the TV screen TRACKING A and V Buttons - Press to manually adjust the tracking. TRACKING AUTO Button - Press for automatic tracking. SPEED Button - Sets the tape speed for recording. 1
16. REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording.
1 F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to activate Forward Search. SET Up/Down Buttons - Press to set clock and timer recording. CHANNEL A and v Buttons - Press to select a channel. CLK SET Button - Press to reset the present time. TVA/CR Button - Press to switch between TV and VCR.
17. TIMER REC Button - Press to set the VCR to start recording at a preset time. 18. 19. 20. 21. 22.
16
-17
1
10
POWER Button - Press to turn the VCR on and off.
2a
Direct Channel Selection Buttons - Press to select any chanrwl.
3.
MEMORY Button - Used to stop the tape when the counter
reaches “0:OO:OO”. 16 - 15
3
14
-13
6
12 -11
8
4a
CLOCK/COUNTER Selector button - Press to cycle between the clock and the linear time tape counter.
5.
PLAY Button - Press to play a prerecorded tape.
60
REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape.
7e 8.
PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen.
9D
TRACKING A and v Buttons - Press to manually adjust the
tracking. 10. TRACKING CEN Button - Press for automatic tracking. 11 e SPEED Button - Sets the tape speed for recording. 120 REC/OTR Button - Press once for normal recording. Additional
CODE NO: 14
pressed activate One-Touch Timer Recording. 13D F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to activate Forward Search. 140 CANCEL Button - Press to clear the selected timer recording program,
15. RESET Button - Press to reset the Linear Time Tape Counter to “0:OO:OO”. 16. 100 Button - Press to select CATV channels 100 to 125. 17. TV/VCR Button - Press to switch between TV and VCR.
47
2.
POWER Button - Press to turn the TV on and off. Direct Channel Selection Buttons - Press to select any channel.
3.
AUTO Button - Used with the CH SET button to set channels into
4.
CH. SET Button - Press to set TV channels into memory.
5m
ADD Button - Press to add a channel into memory.
6a
DELETE Button - Press to delete a channel from memory or to cancel the On/Off Timer program. TIME SET Button - Press to set the Timer or Time. TIMER SEL. - Press to select the timer function to be set. SELECT Button - Press to select the on-screen picture adjustments. MUTE/RESET Button - Press to instantly turn off the sound or to reset the on-screen picture adjustments. VOL V / Min- Button - Press to lower the volume level, set the Minute or set picture adjustments. CHANNEL A and v Buttons - Press to select a channel. VOL A /Hour+ Button - Press to raise the volume level, to set the Hour or set picture adjustments. RECALL Button - Press to display the channel, time and , i STEREO (if channel is broadcasting in stereo) on the TV screen Q. VIEW Button - Press to switch between the last channel viewed and the present channel. SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes.
1. -17 16
memory.
2 -15 14 -13 12 - 11
6
10 -9
7. 8. 90 100
8
1% D 12a 13 cl 140 15. 16.
CODE NO: 15
17. TV/VIDEO Selector Button - Press to select TV or VIDEO for TV viewing.
18
14 2
1m
POWER Button - Press to turn the TV on and off.
20
DirectChannel Selection Buttons - Press to select any channel.
3.
AUTO Button - Used with the CH SET button to set channels into
memory. - 13 12 - 11 10 -9
6
8 -7
4.
CH. SET Button - Press to set TV channels into memory.
5D
ADD Button - Press to add a channel into memory.
6m
DELETE Button - Press to delete a channel from memory.
70
SELECT Button - Press to select the on-screen picture
adjustments 80
MUTE/RESET Button - Press to instantly turn off the sound or to reset the on-screen picture adjustments.
9a
VOL v /(-) Button - Press to lower the volume level or set
picture adjustments. 100 CHANNEL A and v Buttons - Press to select a channel. 11 0 VOL A /(+) Button - Press to raise the volume level or set
picture adjustments. ,
12D RECALL Button - Press to display the channel on the TV screen 13. Q. VIEW Button - Press to switch between the last channel
viewed and the present channel. 14a SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes.
CODE NO: 16
19
-17 16
l2
1.
POWER Button - Press to turn the TV on and off.
2m
Direct Channel Selection Buttons - Press to select any channel.
30
AUTO Button - Used with the CH SET button to set channels into
memory. -1% 14 -13 12
34 5-
- 11 10
-
8
9
4a
CH. SET Button - Press to set TV channels into memory.
CH l/2 Button - Switches between Channel 1 and Channel.2 in the Closed-Caption mode. 6 0 ADD Button - Press to add a channel into memory. 7. DELETE Button - Press to delete a channel from memory. 80 SELECT Button - Press to select the on-screen picture and sound adjustments 9a MUTE/RESET Button - Press to instantly turn off the sound or to reset the on-screen picture and sound adjustments. 10. TV/CAP/TEXT Button - Switches between Caption, Text and TV modes for Closed-Captioned programs. 5m
11 . VOL v /(-) Button - Press to lower the volume level or set
picture adjustments I2. CHANNEL A and v Buttons - Press to select a channel. 13. VOL A /(+) Button - Press to raise the volume level or set picture
adjustments.
CODE NO: 17
.A 14e RECALL Button - Press to display the channel and time on the TV screen. 15. Q. VIEW Button - Press to switch between the last channel viewed and the present channel. 16 . SLEEP Button - Press to set the TV to turn off automatically after ,-
up to 120 minutes. 17. TV/VIDEO Selector Button - Press to select TV or VIDEO for TV viewing.
20
J
1
23
- 22 21 -20
4 57 I
19 - 1 8 17 - 1 6
6 8
-15
1.
TV POWER Button - Press to turn the TV on and off.
2.
VCP POWER Button - Press to turn the VCP on and off.
3.
Direct Channel Selection Buttons - Press to select any channel.
4.
CH. SET Button - Press to set TV channels into memory.
5.
AUTO Button - Used to automatically set all receivable channels
60 70 80 9. 100
11 m 12. 13. 14. 15.
CODE NO: 18
into memory. ADD Button - Press to add a channel into memory. DELETE Button - Press to delete a channel from memory. REPEAT Button - When pressed, the TVAKP will play back the tape over and over until stopped manually. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. TRACKING A and v Buttons - Press to manually adjust the tracking. TRACKING AUTO Button - Press for automatic tracking. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards Press in the Play mode to activate Forward Search.
16. MUTE/RESET Button - Press to turn off the sound. Press again to turn the sound back on. Press to reset the picture
adjustments to their factory preset positions. 17. SELECT Button - Selects on-screen picture adjustments. 18. VOL r/(o) Button - Press to lower the volume level or set picture adjustments. 19. CHANNEL A and v Buttons - Press to select a channel. 20. VOL A/(+) Button - Press to increase the volume level or set picture adjustments. 21 m CALL Button - Press to display the present time/day of the week, channel and counter of the TV screen 22. Quick View Button - Press to switch between the present channel and the last channel selected. 23. SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes.
21
17
2
1a
POWER Button - Press to turn the TV on and off.
2. 3.
Direct Channel Selection Buttons - Press to select any channel. AUTO Button - Used with the CH SET button to set channels into
memory. - 1 6 15 - 1 4 13 -12
9
4 5. l
CH. SET Button - Press to set TV channels into memory.
CH l/2 Button - Switches between Channel 1 and Channel 2 in the Closed-Caption mode. 60 ADD/TIME SET Button - Press to add a channel into memory and to set the timer. 7e DELETE Button - Press to delete a channel from memory. 8. TV/CAP/TEXT Button - Switches between Caption, Text and TV modes for Closed-Captioned programs. 9. TIMER SEL. - Press to select the timer function to be set. 10. SELECT Button - Press to select the on-screen picture adjustments 11 . MUTE/RESET Button - Press to instantly turn off the sound or to reset the on-screen picture adjustments.
12. VOL v/Min (0) Button - Press to lower the volume level , to set the Minute or set the picture adjustments. 130 CHANNEL A and 7 Buttons - Press to select a channel. ’ i 14. VOL A/Hour (=t) Button - Press to raise the volume level, to set the Hour or set the picture adjustments. 15 . RECALL Button - Press to display the channel and time on the TV screen.
CODE NO: 19 :
16. Q. VIEW Button - Press to switch between the last channel viewed and the present channel. 17. SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes.
22
J
25
I-
-24 23
2
3- 22 21 -20 19 - 18
45 6 f 7-
17 -16 89 40 11 12-y--
15 -14 13
NOTE: This remote (code) operates the following Emerson VCR’s: VCR765, VCR765N, VCR885, VCR885N, VCR964, VCR964NTG, VCR964NFC, VCRl795. 10
VCR POWER Button - Press to turn the VCR on and off.
2.
TV POWER Button - Press to turn the TV on and off.
3m
Direct Channel Selection Buttons - Press to select any channel.
4D
AUTO Button - Used with the CH SET button to set channels into
memory, 50
CH. SET Button - Press to set TV channels into memory
60
ADD/TIME SET Button - Press to add a channel into memory
7. 8. 90
10 11: 12a 13b
CODE NO: 20
14m
and to set the timer. DELETE Button - Press to delete a channel from memory. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. VCR CH. (Channel) A and v Button - Press to change channels on the VCR. REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. TIMER SEL. - Press to select the timer function to be set.
15 . F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards Press in the Play mode to activate Forward Search. 16. SELECT Button - Press to select the on-screen picture adjustments. 17 MUTE/RESET Button - Press to instantly turn off the sound. from the TV or to reset the on-screen picture adjustments. ’ a VOL v / Min- Button - Press to lower the volume level, set the Minute or set picture adjustments. 19 20. CHANNEL A and v Buttons - Press to select a channel. 21. VOL A /Hour+ Button - Press to raise the volume level, to set the Hour or set picture adjustments. 21 RECALL Button - Press to display the channel and time on the TV screen. 22: Q. VIEW Button - Press to switch between the last channel viewed and the present channel. 23. SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes. 24D TV/VIDEO Button - Press to select TV or VIDEO 1, 2 for TV viewing. 250 TVNCR Button - Press to select TV or VCR position. l
23
26
-I-
-25 24
2
NOTE: This remote (code) operates the following Emerson VCR’s: VCR765, VCR885, VCR964 1 0 VCR POWER Button - Press to turn the VCR on and off. 2 (I
- 23
45 67 8-
22
30
Direct Channel Selection Buttons - Press to select any channel.
4.
AUTO Button - Used with the CH SET button to set channels into
- 21 20
- 19 18 -17 16
9IO 11 -
-45 14
12 l3-
memory. 5m 6. 7.
8. 9. 100
11\ 0 120 : . :.i$m:. ,- .
130 14D
CODE NO: 21 .
TV POWER Button - Press to turn the TV on and off.
15.
CH. SET Button - Press to set TV channels into memory. ST/SAP Button - Press to switch from stereo (ST) to a second
audio program (SAP) when SAP broadcasting is available. ADD/TIME SET Button - Press to add a channel into memory and to set the timer. DELETE Button - Press to delete a channel from memory. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. VCR CH. (Channel) A and g Button - Press to change channels on the VCR. REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. TIMER SEL. - Press to select the timer function to be set.
16a F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to 17. 18 19: 20Q 21 22: 23. 240 250 26 D
I activate Forward Search. SELECT Button - Press to select the on-screen picture adjustments. MUTE/RESET Button - Press to instantly turn off the sound. from the TV or to reset the on-screen picture adjustments. VOL v / Min- Button - Press to lower the volume level, set the Minute or set picture adjustments. CHANNEL A and v Buttons - Press to select a channel. VOL A / Hour+ Button - Press to raise the volume level, to set the Hour or set picture adjustments. RECALL Button - Press to display the channel and time on the TV screen. Q. VIEW Button - Press to switch between the last channel viewed and the present channel. SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes TVNIDEO Button - Press to select TV or VIDEO 1,2 for TV viewing. TVNCR Button - Press to select TV or VCR position.
24
1.
POWER Button - Press to turn the VCP on and off.
REPEAT Button - Press to repeatedly play back the tape over and over until the STOP button is pressed. 3. PLAY Button - Press to play a prerecorded tape. 4. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. 5. STOP Button - Press to stop the tape. 6. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. 7 TRACKING A and v Button - Press to manually adjust the tracking. 8. TRACKING AUTO Button - Press for automatic tracking. 9. Tape SPEED Button - Sets the tape speed for recording. 10. REC Button - Used to set the VCP to start recording. 11 . EJECT Button - Press to eject the cassette. 12. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to activate Cue Search.
2.
l
42 - 1 1 10 - 9
CODE NO: 22
25
- 17 16 2 -15 14 - 13 12 - 11
6
10
8
-9
10
POWER Button - Press to turn the TV on and off.
2.
Direct Channel Selection Buttons - Press to select any channel.
3.
Picture -/Minutes/CHl/2 Button - Press to decrease the Onscreen picture adjustments, adjust the minutes for clock and on/off Timer, or select Closed Captioned Channels 1 or 2. AUTO MEMORY Button - Press to automatically store all available channels into memory. ADD/DELETE Button - Press to add a channel into memory or delete a channel from memory. Picture +/HoursTTV/CAPTlON/TEXT Button - Press to increase the On-screen picture adjustments, adjust the hours for clock and On/Off Timer, or select between Closed Captioned Captions and full screen text. PICTURE Button - Press to access On-screen picture adjustments of Contrast, Color, Sharpness, Brightness and Tint. CAPTION Button - Activates the CCD (Closed Captioned Decoder) for hearing impaired viewers. TIMER SELECT Button - Press to select Clock, On Timer or Off Timer. MUTE Button - Press to turn off the sound. Press again to turn .i the sound back on. VOLUME Down Button - Press to lower the volume level. CHANNEL A and v Buttons - Press to select a channel. VOLUME Up Button - Press to increase the volume level.
4. 5a 60
7. 8D 9d 100 11 a 12 . 13.
CODE NO: 23 :
14. CALL Button - Press to display the channel number, time and Off time or Sleep time (if set) on the TV screen 15, 100 Button - Press to enter a channel over 99. 16. SLEEP Button - Press to set the TV to turn off automatically after up to 90 minutes. 17. TVKATV Button - Used to choose between VHF/UHF (TV) or Cable TV (CATV) channels.
23
-19 2
1.
POWER Button - Press to turn the VCR on and off.
2. 30 4.
Direct Channel Selection Buttons - Press to select any channel.
18
5. 60
6
- 1 6 15 - 1 4
7, 8m
8
1312
90
11 -10
i
10.
11. 12. 13e
CODE NO: 24
14m
MENU Button - Press to display the On-screen menu function. CURSOR Buttons - While in the Play mode, press these buttons to adjust for softer or sharper definition. Press these buttons during Pause mode to reduce picture shakiness. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. a VCR CHANNEL/TRACKING A and v Buttons - Press to manually adjust the tracking or to select a channel for viewing or recording. SHUTTLE Buttons (VR4450 Only) - Press to play back forward or backward 3, 5 or 7 times the normal speed in SP mode (5x, 9X or 21x in LP, EP). REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. SPEED Button - Press to select a recording tape speed (SP/LP/EP). SLOW Button (VR4450 Only) - Press to view the picture slowly 3s Button - Press to select the Super Simple System of the
Timer Programming. 15. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to 16. 17. 18. 19* 20.
activate Forward Search. END +,- Buttons - Press to adjust the end time of the 3S Timer Recording. START +,- Buttons - Press to adjust the start time of the 3S Timer Recording. 100 Button - Press to select a channel over 99. TVNCR Button - Press to switch between TV and VCR. INPUT Button - Press to select between the VCR tuner or the unit connected to the AUDlONDEO lN jacks.
25 l-
- 2 4
2 4 56
23 - 2 2
-
8 21 - 20
=I8 17 - 16
CODE NO: 25 I
POWER Button - Press to turn the VCR on and off.
20 30
Direct Channel Selection Buttons - Press to select any channel. COUNTER RESET Button - Used to reset the Linear Time Tape
Counter to “0:OO:OO”. DISPLAY Button - Press once to display the time, date and VCR mode and channel on the TV screen. Press twice to display only the clock (or tape counter, if on). Press again to remove the display. 5 . VISSITIME Button - Press this button once to enter VISS mode. Press again to enter the Time Search mode. 6 . CLEAR/MONITOR Button - Press to erase the last digit or to go back to the last entry when inputting data in the menu screen. In the Program Review menu screen, press to cancel a program. Press this button during playback to view the channel selected on the VCR. 7. ADD/ERASE Button - Press to add or delete a channel from memory. 8 . MENU Button - Press to display the On-screen menu function. 9 .\ CLOCK/COUNTER/REMAIN Selector button - Press to cycle between the clock, linear time tape counter and remaining tape time modes on the display. .4 10. PLAY (2X) Button - Press to play a prerecorded tape. Press again to advance the tape at twice the normal speed. 1L REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. 4.
3
7
1.
12. STOP Button - Press to stop the tape. 13. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. 14. TRACKING A and V Buttons - Press to manually adjust the tracking. 15. TRACKING AUTO Button - Press for automatic tracking. 16. Slow Speed Up and Down Buttons - Press during playback to speed up or slow down slow motion playback. 17. REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. 18. Tape SPEED Button - Press to select a recording tape speed (SP/EP). 19. F.ADV Button - Press in the Pause/Still mode to advance the tape one frame. 20. EJECT Button - Press to eject a tape. 21. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to
activate Forward Search. 22. 23. 24. ,A, 25.
CHANNEL A and V Buttons - Press to select a channel. 100 Button - Press to select a channel over 99. TU/AV Button - Press to select an input source for the VCR. WNCR Button - Press to switch between TV and VCR.
28
10
1 20 3-
2. 3.
“OHOOMOOS”. - 19 18 - 17
4. 5. 6. 7s
16
r
4
-
- 1 5
8.
6
5 7 -
14 - 1 3
9.
8
POWER Button - Press to turn the TV/VCR on and off. Direct Channel Selection Buttons - Press to select any channel. RESET Button - Press to reset the Linear Time Tape Counter to
100
9 10 -
11 0 12. 130
14m
CODE NO: 26
MENU Button - Press to call up the MENU screen 100 Button - Press to select a channel over 99. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind
the tape backwards. Press in the Play mode to activate Reverse Search. STOP/EJECT Button - Press to stop the tape. Press again to eject the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. TRACKING/VCR CHANNEL/SET A and v Buttons - Press to manually adjust the tracking or to select TV channels. Also, use these buttons to adjust the picture modes (Contrast, Brightness, Color, Tint and Sharpness). Tape SPEED Button - Press to select a recording tape speed (SP/EP). REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to activate Forward Search. ENTER M (Memory) Button - Press to enter information for timer recording, clock setting and counter memory when going to the next step of an operation.
15. MUTE Button - Press to turn off the sound. Press again to turn the sound back on. 16. VOLUME Down Button - Press to lower the volume level. 17. VOLUME Up Button - Press to increase the volume level. 18. RECALL Button - Press to display the channel being viewed, time, VCR mode, tape speed and tape counter. Press
again to turn off the display. If the RECALL button is pressed when closed captions are being used, the captions will not be displayed. 19. Quick View Button - Press to switch between the present channel and the last channel selected. 20. SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes.
29
l-
18
2
34 56 78
10
POWER Button - Press to turn the TV on and off.
2.
Direct Channel Selection Buttons - Press to select any channel.
CHlKH2 Button - Switches between channel 1 and channel 2 of the Closed Caption mode. 4. CH SET Button - Press to set channels into memory. 5 D AUTO Button - Press to automatically store all available channels into memory. 8 0 ADD/DELETE Button - Press to add a channel into memory or delete a channel from memory. 9 0 TV/CAPTION/TEXT Button - Press to select between Closed Captioned Captions full screen text and TV modes. 8 a PICTURE Button - Press to select on-screen picture adjustments 90 100 Button - Press to select channels over 99. 100 CLOCK/TIMER Button - Press to select the clock, everyday timer or one time timer. 11 a SET Button - Press to set the clock, everyday timer or one time timer. 120 MUTE/RESET Button - Press to turn off the sound. Press again to turn the sound back on. Also used to reset the on-screen picture .A adjustments. 30
-17 16 - 15 14 - 13 12 - 14
13. VOLUME Down Button - Press to lower the volume level. 14. CHANNEL A and v Buttons - Press to select a channel. 15. VOLUME Up Button - Press to increase the volume level.
0
16, CALL Button - Press to display the channel number, and Closed Caption mode (if set) on the TV screen. 17. QUICK VIEW Button - Press to switch between the present channel and the last channel viewed. 18. SLEEP Button - Press to set the TV to turn off automatically after up to 90 minutes.
NOTE: The CHI/L (3) and the TV/CAP/TEXT (7) buttons are not functional for models TC1369 and TCI 366.
30
1.
=l
- 3 0 29
2. 3.
'24
POWER Button - Press to turn the TV/VCR on and off. Direct Channel Selection Buttons - Press to select any channel. RESET Button - Press to reset the Linear Time Tape Counter to
“00:00:00”. 4a
3 -
- 28 27 - 2 6 25 - 2 4 23 - 2 2 21
5 r67 8 -
9 10 II 12 -
-ic2* - 1 8 17 - 1 6
13 =i4-15
5m 60 70 8. 9. 10 11:
7’
12. 130 14. 15 161
CODE NO: 28
MEMORY Button - Used to stop the tape when the counter reaches “OO:OO:OO”. . CH l/2 Button - Switches between Channel 1 and Channel 2 in the Closed-Caption mode. TV MONITOR Button - Press to temporarily view A TV channel selected while in the Playback mode. MENU Button - Press to display the on-screen function menu. CANCEL Button - Press to clear the selected timer recording program. PROG. CONFIRM Button - Press to confirm the programmed timer recording. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. TRACKING A and v Buttons - Press to manually adjust the tracking. TRACKING AUTO Button - Press for automatic tracking. Tape SPEED Button - Press to select a recording tape speed (SP/LP/SLP).
17a REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. 18* TIMER REC Button - Press to set the VCR to start recording at a preset time. 19. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to
activate Forward Search. ?O . ENTER Button - Press to enter information . 21 0 SET UP/DOWN Buttons - Used to set the clock, timer recording, auto repeat, channel set, picture adjustment and language. 22 . MUTE Button - Press to turn off the sound. Press again to turn the sound back on. 23 TV/CAP/TEXT Button - Switches between Caption, Text and TV modes for Closed-Captioned programs 24: VOLUME Down Button - Press to lower the volume level. 25 . CHANNEL UP/DOWN Buttons - Press to select a channel. 26 . VOLUME Up Button - Press to increase the volume level. 27 m CALL Button - Press to display the present time/day of the week, channel, speed selection, counter (and VCR mode if VCR is operating) on the TV screen. 28. QUICK VIEW Button - Press to switch between the present channel and the last channel selected. %9. SLEEP Button - Press to set the TV to turn off automatically after up to 120 minutes 30 D RESET Button - Press to reset the on-screen picture adjustments. NOTE: The CH1/2 (5) and the TV/CAP/TEXT (23) buttons are not fUnctional for models VT0954A and VT0955A. 31
28
I 2-
10
POWER Button - Press to turn the VCR on and off.
20
Direct Channel Selection Buttons - Press to select any channel.
3.
MEMORY Button - Used to stop the tape when the counter reaches “O:OO:OO”. VISS Button - Press to search for Index marks. CH. SKIP (Channel SKIP) Button - Used to skip over unwanted channels. TV MONI. Button - Press to temporarily view a TV channel selected on the VCR while in the Play mode. CANCEL Button - Press to clear the selected timer recording program. MENU Button - Press to display the On-screen menu function. ENTER Button - Press to enter information for timer recording and clock setting. CLOCK/COUNTER Selector button - Press to cycle between the clock and the linear time tape counter. PLAY Button - Press to play a prerecorded tape. REW (Rewind) Button - Press in the Stop mode to rapidly wind the tape backwards. Press in the Play mode to activate Reverse Search. .A STOP Button - Press to stop the tape. PAUSE Button - Press in the Play mode to pause the tape and display a still picture on the TV screen. TRACKING A and v Buttons - Press to manually adjust the tracking.
4m 3 4
-
- 27
5D
26
6m
- 25 24
70
- 2 3
80 90
5
6
7 8 1 0 9 11 12 l314 l516
2221
2019 18
-97
100 11 0 120 \ 13a 140 15 0
CODE NO: 29
16 0 TRACKING AUTO Button - Press for automatic tracking. 17 . Slow Speed Up and Down Buttons - Press to speed up or slow down slow motion playback.
I
18 0 REC/OTR Button - Press once for normal recording. Additional pressed activate One-Touch Timer Recording. 19 0 Tape SPEED Button - Press to select a recording tape speed (SP/LP/EP). 20 . SLOW Button - Press in the Play mode to activate slow motion playback. Press in the Pause/Still mode to advance
one frame. 22: 21 TIMER REC Button - Press to set the VCR to start recording at a preset time. EJECT Button - Press to eject a tape. 23. F.FWD (Fast Forward) Button - Press in the Stop mode to rapidly wind the tape forwards. Press in the Play mode to 24 0 25 0 26 27: I’I 28 -
activate Forward Search. SET Up/Down Buttons - Press to set clock, timer recording, auto repeat and language. SKIP Search Button - Press in the Play mode to search forward through approximately 30 seconds of tape. CHANNEL A and V Buttons - Press to select a channel. RESET Button - Press to reset the Linear Time Tape Counter to “0:OO:OO”. TV/VCR Button - Press to switch between TV and VCR.
32
1. - 1%
2. 3.
15 - 14 13 - 12 11 - 10
6
9 -
8
4. 5.o 6. a0 a
9II
100 11 0 12a 13. 140 15a
CODE NO: 30
160
POWER Button - Press to turn the TV on and off. Direct Channel Selection Buttons - Press to select any channel. AUTO PROGRAM Button - Press to start Auto Programming in the Program mode. CH SET Button - Press when setting and cancelling TV channels. ADD Button - Press to add a-channel into memory. DELETE Button - Press to delete a channel from memory. FINE TUNING Buttons - When AFT is deactivated, these controls operate as Fine Tuning Up/Down buttons. SELECT Button - Press to select on-screen picture adjustments MUTE/RESET Button - Press to turn off the sound. Press again to turn the sound back on. Also used to reset the on-screen picture adjustments. VOLUME Down Button - Press to lower the volume level or onscreen picture adjustments CHANNEL A and v Buttons - Press to select a channel. VOLUME Up Button - Press to increase the volume level or onscreen picture adjustments. RECALL Button - Press to display the channel number on the TV screen. AFT Button - Press to activate or deactivate automatic fine tuning. Quick View Button - Press to switch between the present channel and the last channel selected. SLEEP Button 7 Press to set the TV to turn off automatically after ’ up to 90 minutes.
33
TRQUBLESHQQTING G U I D E Before returning unit or requesting service, please refer to the following chart for the symptom and possible solution.
Remove obstruction
VCR, TV or Combo is not working.
incorrect Remote code.
Reset remote code.
Batteries were removed from remote for more than 15 minutes
Press the RESET button in the battery compartment and reset the code.
Power cord is not plugged in. \
Plug AC power cord into a standard 12OV, 60Hz outlet.
SERVICE FOR CUSTOMER SERVICE, PLEASE WRITE TO: Emerson Radio Corp. ’ Consumer Affairs Dept. 9 Entin Road, Parsippany, NJ 07054-0430 34
7’
EMERSON PART NO. 70-6400 61 O-01
