Transcript
Description Body Socket Insulation O-Ring Crimp ring Washer Nut Heat Shrink H0.433 (11.00)
Material Brass BE CU PTFE SI Rubber Brass Brass Brass Polyolefin
Finish Nickel Gold N/A Rubber Nickel Nickel Nickel Black
0.098 (2.50)
REVISIONS
0.276 (7.00)
REV
RG-58 Cable
B
DESCRIPTION Updated dimensions; Added new title block
FLAT 0.228 (5.80)
10-JUL-12
BPM
Ø0.020 (0.50)
0.2x2x2 GROOVE
Ø0.049 (1.24)
0.587 (14.90)
0.984 (25.00)
HEAT SHRINK
Ø0.039 (1.00)
SOCKET
0.083 (2.10)
APPV
Ø0.287 (7.30)
PIN CHUCK
Ø0.177 (4.50)
0.228 (5.80)
DATE
RECOMMENDED CABLE STRIPPING DIMENSIONS
1/4-36UNS-2A THREADS
1/4-36UNS-2A THREADS
0.098 (2.50)
Ø0.256 (6.50)
Ø0.402 [10.20]
0.472 (12.00)
H0.315 [8.00]
1/4-36UNS-2B THREADS
1.059 (26.90)
SIDE VIEW
Ø0.236 (6.00)
Ø0.358 (9.10)
0.500 (12.70) 0.234 [6.00]
0.065 [1.65]
NUT
0.020 [0.50]
CRIMP RING
Ø0.256 [6.50]
WASHER RECOMMENDED MOUNTING HOLE
0.055 (1.40)
NOTES: (UNLESS OTHERWISE SPECIFIED) 1. ALL DIMENSIONS ARE IN INCHES [mm]. 3. MANUFACTURE TO BE COMPLIANT WITH EU RoHS DIRECTIVE. 2. DIMENSIONS APPLY AFTER FINISHING. 4. SAFETY BREAK ALL SHARP CORNERS AND EDGES .02 MAXIMUM. : THIS DRAWING CONTAINS PROPRIETARY INFORMATION 159 ORT LANE
CONSMA014-R58 ASSEMBLY INSTRUCTIONS 1. Strip the cable to recommended dimensions. O-RING THAT IS THE SOLE PROPERTY OF LINX TECHNOLOGIES, AND SHALL BE 2. Slip heat shrink and crimp ring onto stripped cable. MERLIN, OR 97532 TREATED AS SUCH. NO DISCLOSURE OR REPRODUCTION OF THIS 3. Insert o-ring into groove in the nut on body. DOCUMENT IS PERMITTED, IN WHOLE OR IN PART, WITHOUT THE TITLE: 4. Solder the socket to the center conductor. EXPRESS WRITTEN PERMISSION OF LINX TECHNOLOGIES OR ITS DESIGNATED AGENTS. SMA FEMALE BULKHEAD MOUNT CABLE 5. Insert the socket, center conductor, and insulation into the body. PROJECTION: MATERIAL: TOLERANCES: 6. Wrap the braid around the tail of the body and crimp the ring with END CRIMP WITH O-RING FOR RG58 CABLE .020 [0.50]-.200 [5.00]= .008 [0.20] .200 [5.00]-1.200 [30.00]= .016 [0.40] 0.213" hex crimp tool (or one labeled for use with RG-58 cable). 1.20 [30.0]-4.75 [120.0]= .024 [0.60] SIZE DWG. NO. REV 4.75 [120.0]-12.40 [315.0]= .040 [1.0] ANGLES: 1 7. Use heat shrink to cover crimp. FINISH: CONSMA015-R58 B 8. Use the nut and washer to secure the connector to a case. DRAWN: B.MURPHY DT: 10-JUL-12 (2.50mm maximum wall thickness) DO NOT SCALE DRAWING SHEET 1 OF 1 ENGR: S.HOGAN DT: 10-JUL-12 SCALE: 2:1 LDCFDLT_A
