Preview only show first 10 pages with watermark. For full document please download

TechBook in.k300 TM the essential spa keypad Bright LCD screen Spa function icons Affordable 9919-101218-B Rev. 01-2014 © Groupe Gecko Alliance Inc., 2014 All trademarks or registered trademarks are the property of their respective owners. Gecko Alliance 450 des Canetons, Quebec City (Qc), G2E 5W6 Canada, 1.800.78.GECKO 9225 Stellar Court, Corona, CA 92883 USA, 951.667.2000 www.geckoalliance.com Printed in Canada in.k300 TechBook 3 Table of contents Warnings �� 2 Introduction �� 3 in.k300 keypad layout �� 4 in.k300 dimensions �� 4 Installation of in.k300 �� 4 Drilling template �� 5 Installation notes �� 6 Connecting in.k300 keypad to the spa pack �� 6 Keypad functions �� 7 -- Start or stop accessories �� 7 -- Water temperature �� 7 -- Off Mode �� 7 Programming steps �� 8 -- Program menu �� 8 -- Setting the clock �� 8 -- Programming the filter/ purge cycles �� 8 -- Setting filter or purge cycle start time �� 9 -- Setting filter cycle duration �� 9 -- Setting filter or purge cycle frequency �� 9 -- Setting economy mode �� 9 -- Setting economy start time �� 9 -- Setting economy duration �� 10 -- Setting temperature unit �� 10 -- Smart Winter Mode �� 10 -- Cooldown �� 10 -- Water temperature regulation �� 10 Error messages �� 11 Specifications �� 12 1 in.k300 TechBook 3 Warnings WARNINGS: Before installing or connecting the unit, please read the following. FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS MAY SIGNIFICANTLY SHORTEN THE PRODUCT’S LIFE TIME, AND LEAD TO FAILURES AS WELL AS HAZARDOUS CONDITIONS*. COMMON SENSE MUST ALWAYS PREVAIL WHEN EVALUATING THE INSTALLATION AND/OR USE OF ANY ELECTRONIC CONTROL IN A FINAL APPLICATION. • RESPECT ENVIRONMENTAL CONDITIONS LISTED AT END OF TECHBOOK. • THIS UNIT MUST BE INSTALLED BY QUALIFIED PERSONNEL. • ONLY QUALIFIED PERSONNEL ARE TO SERVICE THIS UNIT. THERE ARE NO USER SERVICEABLE PARTS INSIDE. • THIS UNIT SHOULD BE INSTALLED ON A CLEAN FLAT SURFACE. • THE GASKET ON THE BACK OF THE UNIT WILL PREVENT WATER INFILTRATION INSIDE, BEHIND THE MOUNTED SURFACE. IF THE GASKET IS DAMAGED, SEAL THE BACK OF THE UNIT WITH SILICONE TO AVOID ANY LEAKAGE BEHIND THE MOUNTED SURFACE. • THIS UNIT MUST BE MOUNTED ON THE OUTSIDE EDGE OF THE SPA. SEE INSTALLATION SECTION FOR DETAILS. • THE BACK OF THIS UNIT SHOULD NOT BE ENCLOSED IN A WAY THAT CAUSES WATER TO COLLECT. SEE INSTALLATION SECTION FOR DETAILS. * HAZARDOUS CONDITION: A CONDITION THAT IS POTENTIALLY DAMAGING AND/OR DANGEROUS TO THE OPERATOR OR SURROUNDINGS. THIS INCLUDES, BUT IS NOT LIMITED TO: FIRE, FLOODING OR OTHER WATER DAMAGE, DIELECTRIC BREAKDOWNS (PRESENCE OF HIGH VOLTAGE), ETC. MAINTENANCE If you have problems, do not attempt to repair the unit yourself. Return it to your dealer or service station for servicing. ACCESSORY PARTS Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure. DISPOSAL OF THE PRODUCT The appliance (or the product) must be disposed of separately in accordance with the local waste disposal legislation in force. Compatible spa packs: in.xm2, in.xe, in.yt, in.yj, and in.ye with compatible software revision. Aeware®, Gecko®, and their respective logos are Registered Trademarks of Gecko Alliance Group. in.k300™, in.xm2™, in.xe™, in.yt™, in.ye™, and in.yj™ and their respective logos are trademarks of Gecko Alliance Group. All other product or company names that may be mentioned in this publication are tradenames, trademarks or registered trademarks of their respective owners. 2 in.k300 TechBook 3 Introduction in.k300 the essential spa keypad The in.k300 brings all the features you really need to one keypad. Compact, with a big LCD screen; bright enough to be seen in day, simple enough to use in the middle of the night; affordable, yet solidly built. Item Static LCD size (as measured diagonally) in.k300 1.5" Optional mounting with wing-nuts and spacers Double-sided bezel gasket Icons giving instant spa status information Number of pumps/blowers supported 1 or 2 Time display 3 in.k300 TechBook 3 in.k300 keypad layout 1 Pump Model 2 Pump Model Pump 1 Light Indicator lights Smart Winter Mode Pump 1 Pump 2 Up Down Light Indicator lights Up / Down Heater Filter Set Point in.k300 dimensions Installation of in.k300 Gasket with or without adhesive 2.25" (57.15 mm) 6.30" (160.02 mm) Optional wing nuts and spacers 1.87" (47.45 mm) To install the in.k300, use the drilling template provided in this section. Determine the mounting location and stick the template on chosen location. Cut out an opening according to the template. Clean the installation surface and peel the adhesive gasket from the back of the keypad. Insert keypad and align it correctly, then ensure it is properly glued by gently pressing evenly on the entire surface. 4 in.k300 TechBook 3 Drilling template 1.44" 36.58 mm 5.67" 144.02 mm 5.17" 131.32 mm R0.25" 6.35 mm R0.25" 6.35 mm 5 in.k300 TechBook 3 Installation notes Keypad placement Vent hole on back of keypad should not be blocked. The back of the in.k300 should not be enclosed where water can gather, but instead cut out. It is recommended to install the in.k300 on the outside edge of the hot tub, so that it is not subject to moisture trapped by the cover. Connecting in.k300 keypad to the spa pack Main keypad in.k300 To connect the in.k300 keypad, simply insert its in.link connector into the appropriate keypad connector of the pack enclosure (as illustrated). 6 in.k300 TechBook 3 Keypad functions Start or stop accessories To start or stop an accessory, press the associated button. Indicators will light up when the associated accessory is on. When an accessory has more than two states, press the button until it reaches the desired state. Indicators will flash when dual speed pumps are on at low speed, and will be solid at high speed. If you have a blower it will be controlled by the Pump 2 key. The order of actions is as follows: pump 2 on; pump 2 high speed (if applicable); blower on; pump 2 off; blower off. Water temperature The temperature shown on screen is the current water temperature. Use the Up and Down buttons to set the desired temperature. The set point icon will appear at the top of the screen. After 3 seconds without any change to the set temperature value, the keypad will resume the normal display. Off Mode Pressing Pump 1 for 5 seconds will enable the Off mode. This mode allows you to stop all outputs including automatic functions such as filter cycle, heat request and smart winter mode for 30 minutes to perform quick spa maintenance. When Off mode is active, the display will toggle between the “OFF” message, the clock and the water temperature. The spa light will flash for a few seconds before the end of the 30 minutes to warn you that the system is about to resume its normal operation. Press Pump 1 or Pump 2 (if available) to restart the system before the expiration of the 30 minute delay. When the system resumes its normal operation, the display shows “On“ for 3 seconds. 7 in.k300 TechBook 3 Programming steps Program menu The program menu is accessible by holding down the Light key for 5 seconds. In the program menu the following parameters can be set: clock, filter or purge cycles, economy mode and temperature units. While in the program menu, use the Up or Down key to adjust the parameters and use the Light key to jump to the next parameter. The changes will be saved after the confirmation of the last parameter only. If there is no action taken for 10 seconds, the system will exit the program menu without saving any changes. Setting the clock Enter the program menu by holding down the Light key for 5 seconds. The display will show the current clock setting with the hour flashing. Depending on factory settings your system may be set to 24-hour time or 12-hour time. Setting the hour: Use the arrow keys to adjust the hour. Press the Light key to jump to the next parameter, the minutes. Setting the minutes: Use the arrow keys to adjust the minutes. Press the Light key to jump to the next parameter, the filter or purge start time (FS). Programming the filter/ purge cycles Depending on system configuration your spa will perform either a filter or a purge cycle. The filter cycle menu consists of the following parameters: the start time (FS), the duration (Fd) and the frequency (FF). The purge cycle menu consists of the following parameters: the start time (FS) and the frequency (FF). A filter cycle consists of starting all the pumps and blower in high speed for 1 minute (purge step) then, the pump associated with the filter will run in low speed for the remaining duration of the filter cycle (clean step). A purge cycle is used when the spa is equipped with a 24 hour circulation pump which provides a continuous clean step. It consists of starting all the pumps and blower in high speed for 1 minute. 8 in.k300 TechBook 3 Setting filter or purge cycle start time The display will show FSxx, “xx” representing the starting hour of the cycle. Use the arrow keys to adjust the hours. Use the Light key to jump to the next parameter, filter duration (Fd). Setting filter cycle duration (not available on purge systems) The display will show Fdxx, “xx” representing the duration in hours of the filter cycle. Use the arrow keys to adjust the duration. Use the Light key to jump to the next parameter, filter or purge frequency (FF). 0 = no filtration 24 = continuous filtration It is not recommended to set this to "0". Setting filter or purge cycle frequency The display will show FFxx, “xx” representing the number of cycles per day. Use the arrow keys to adjust the frequency. Use the Light key to jump to the next parameter, economy mode (EP). The “Filter” indicator lights up when filter is on and flashes when suspended. Setting economy mode This mode allows you to lower the temperature set point of the spa by 20 °F (11 °C) during a certain period of the day. The display will show EPx, “x” representing the state of the programmed economy (0 = disabled, 1 = enabled). Use the arrow keys to enable or disable economy mode. Use the Light key to jump to the next parameter, economy start time (ES). When the Economy mode is ON, the display will toggle between the “Eco” message, the time, and the water temperature. Setting economy start time The display will show ESxx, “xx” representing the hour at which the economy mode will become active. Use the arrow keys to adjust the hour. Use the Light key to jump to the next parameter, economy duration (Ed). 9 in.k300 TechBook 3 Setting economy duration The display will show Edxx, “xx” representing the duration in hours of the economy mode. Use the arrow keys to adjust the hour. Use the Light key to jump to the next parameter, temperature unit. 24 = continuous economy Setting temperature unit Water temperature can be displayed in either Fahrenheit (°F) or Celsius (°C). The display will show °F or °C. Use the arrow keys to change the setting. Use the Program or Light key to save all the parameters. Smart Winter Mode Our Smart Winter Mode protects your system from the cold by turning pumps on several times a day to prevent water from freezing in pipes. The “SWM” indicator lights up when freezing is detected and flashes when the purge is active. Cooldown After heating the spa water to the desired Set Point, the heater is turned off, but its associated pump (Pump 1 low-speed or CP) remains on for a predetermined period of time to ensure adequate cooling of the heating element, prolonging its useful life. Water temperature regulation Every 15 to 90 minutes the pump will run to ensure accurate water temperature readings as well as avoid heater activation in dry conditions. After verifying pump activation and taking a water temperature reading if required, the system automatically turns the heater on to reach and maintain water temperature at Set Point. Indicator flashes when taking water temperature reading. 10 in.k300 TechBook 3 Error messages The list below shows the different error messages that can appear on the home screen. Refer to the troubleshooting and error codes section of the TechBook for your spa pack for more details. Code Message HL Warning! HL Error FLO No flow for more than 2 hours FLO No flow condition HR Danger! Relay stuck OH Warning! Spa temp. high Prr Warning! Temp. probes defective AOH Internal pack temp. high FLC Flow switch closed SP in Input voltage issue FrEr The input frequency is out of range RH NC Comm. error in.xm2 - in.therm RH ID in.xm2 - in.therm incompatible SC ER Learning mode error F1 in.xm2 Fuse # 1 is blown F2 in.xm2 Fuse # 2 is blown F3 in.xm2 Fuse # 3 is blown Hr Danger! Thermal fuse error UPL The spa pack does not have valid software. Please insert valid in.stick to reprogram spa pack. BL The spa pack does not have valid software. Please insert valid in.stick to reprogram spa pack. 11 in.k300 TechBook 3 Specifications Part number 1 pump model: 0607-008036 2 pump model: 0607-008037 Model IN.K300-CL-GE1 Environmental Operating temperature: Storage temperature: Humidity: Water ingress protection: -68°F (-20°C) to 149°F (65°C) -22°F (-30°C) to 185°F (85°C) Up to 70% condensing IPX-5 Mechanical Weight: Dimensions (W x H x D): 0.69 lb (313 g) 2.25” x 6.30” x 1.87” (57.15 mm x 106.02 mm x 47.45 mm) Compatibility in.yj, in.yt, in.ye, in.xe, or in.xm2 spa packs with appropriate software revision Specifications and design are subject to change without prior notice. 12 TechBook in.k300 TM the essential spa keypad Bright LCD screen Spa function icons Affordable 9919-101218-B Rev. 01-2014 © Groupe Gecko Alliance Inc., 2014 All trademarks or registered trademarks are the property of their respective owners. Gecko Alliance 450 des Canetons, Quebec City (Qc), G2E 5W6 Canada, 1.800.78.GECKO 9225 Stellar Court, Corona, CA 92883 USA, 951.667.2000 www.geckoalliance.com Printed in Canada

Similar Pages

Rating

Date

Size

Views

Categories

Share

Transcript

Forgot your password?.