Transcript
SP205+
DUAL 1x5 VIDEO & AUDIO DISTRIBUTION AMPLIFIER
• Two separate 1x5 video and stereo audio sections • Possibility of 1x5 dual or 1x10 single configuration • Suitable for composite or Y/C signals • Suitable for unbalanced stereo audio or mono balanced signals
Ed. 1 11/12/2008
ELPRO Video Labs s.r.l. 1
Str.da della Pronda, 45/B 10142 TORINO - ITALY Tel.+39 0117701583 – Fax +39 011703751
SP205+
DUAL 1x5 VIDEO & AUDIO DISTRIBUTION AMPLIFIER
1
INSTALLATION AND USE OF THE SP205+
SUMMARY 1.0
Overview
3
2.0
Power supply
4
3.0
Installation
5
4.0
Technical data
9
5.0
Notes
10
When installing the SP205+ unit, please read this handbook carefully. The manufacturer shall not be held responsible for damage due to use, even correct, of its products. The data and characteristics of the product may be modified without prior notice. All updates and news regarding this products are published on our site www.elprovideolabs.com
ELPRO Video Labs s.r.l. Str.da della Pronda, 45/B 10142 TORINO - ITALY Tel.+39 0117701583 – Fax +39 011703751
2
SP205+
1.0
DUAL 1x5 VIDEO & AUDIO DISTRIBUTION AMPLIFIER
OVERVIEW
Thank you for purchasing this product. Check the contents of the packaging carefully. It contains: The SP205+ unit
This handbook and the certificate of conformity
The power cord
The SP205+ is a dual 1x5 video and stereo audio distributor that can, if necessary, be configured as a single 1x10 distributor.
ELPRO Video Labs s.r.l. 3
Str.da della Pronda, 45/B 10142 TORINO - ITALY Tel.+39 0117701583 – Fax +39 011703751
SP205+
DUAL 1x5 VIDEO & AUDIO DISTRIBUTION AMPLIFIER
1
2.0
POWER SUPPLY
The SP205+ must be powered at 90÷240 Vac 50/60Hz using the cable provided. The socket of the cable must be inserted in the related panel plug to the left on the back of the unit. The panel plug is equipped with a fuse holder for 5X20 fuses. If the fuse blows, replace it with one of the same rating that’s 1AT.
All operations must be carried out by qualified personnel only, who must be informed of the risks of electric shock. In some countries, the plug of the cable must be adapted to local standard types. The wires are coded as follows: Brown PHASE Identified by the letter L, may be red Blue NEUTRAL Identified by the letter N, may be black Yellow/green GROUND Identified by the letter E, may be green
WARNING A ground connection is compulsory
ELPRO Video Labs s.r.l. Str.da della Pronda, 45/B 10142 TORINO - ITALY Tel.+39 0117701583 – Fax +39 011703751
4
SP205+ 3.0
DUAL 1x5 VIDEO & AUDIO DISTRIBUTION AMPLIFIER
INSTALLATION
3.1 Video section 3.1.1 Dual 1x5 distributor
To use the unit as dual 1x5 distributor with two sources, proceed as follows: a) Make sure that all the units to be installed are OFF. b) Set the switch on the front panel to the “DUAL 1x5” position remembering that this setting acts not only on the video but also on the audio. c) Connect the first video source to one of the two IN1 connectors and the second source to one of the two IN2 connectors. d) If the input signal is not terminated at 75Ω, set the matching switch to the ON position. If the signal is already terminated at 75Ω, set the switch to OFF. The switch of input IN1 is located to the left of the respective BNCs, that of input IN2 is located to the right. e) The input BNC not used can be left free or can be used, if necessary, to send the video signal to other units. In this case, remember that termination at 75Ω must be carried out at only one point of the chain, preferably at the end of this. Therefore, in this case, the 75 Ohm switch must be set to a OFF. f) Connect the destinations to BNCs 1÷5 “VIDEO OUT” on both sections. The BNCs at the top refer to section 1, those at the bottom refer to section 2. g) Power the SP205+ and other system units.
ELPRO Video Labs s.r.l. 5
Str.da della Pronda, 45/B 10142 TORINO - ITALY Tel.+39 0117701583 – Fax +39 011703751
SP205+
DUAL 1x5 VIDEO & AUDIO DISTRIBUTION AMPLIFIER
1
3.1.2 Single 1x10 distributor
To use the unit as 1x10 single distributor, proceed as follows: a) Make sure that all the units to be installed are OFF. b) Set the switch on the front panel to the “1x10” position remembering that this setting acts not only on the video but also on the audio. c) Connect the video source to one of the two IN1 connectors d) If the input signal is not terminated at 75Ω, set the switch referring to the IN1 input (located to the left of the related BNCs) to the ON position. If the signal is already terminated at 75Ω, set the switch to OFF. The position of the switch relating to IN2 is not significant in this operating mode. e) The BNC not used, relating to input IN1, can be left free or can be used, if necessary, to send the video signal to other units. In this case, remember that termination at 75Ω must be carried out at only one point of the chain, preferably at the end of this. Therefore, in this case, the 75 Ohm switch must be set to a OFF. f) As the two IN2 connectors are not used in this operating mode, connection of these is not significant. g) Connect the destinations to the “VIDEO OUT” BNCs. h) Power the SP205+ and other system units.
ELPRO Video Labs s.r.l. Str.da della Pronda, 45/B 10142 TORINO - ITALY Tel.+39 0117701583 – Fax +39 011703751
6
SP205+
DUAL 1x5 VIDEO & AUDIO DISTRIBUTION AMPLIFIER
3.2 Audio section 3.2.1 Dual 1x5 distributor
To use the unit as dual 1x5 distributor with two sources, proceed as follows: a) Make sure that all the units to be installed are OFF. b) Set the switch on the front panel to the “DUAL 1x5” position remembering that this setting acts not only on the video but also on the audio. c) Connect the first audio source to the AUDIO IN1 connectors and the second source to the AUDIO IN2 connectors. If the source is mono, only one of the two channels (L or R) can be used. d) Connect the destinations to the AUDIO OUT1 and AUDIO OUT2 connectors respectively. e) Power the SP205+ and other system units. 3.2.2 Single 1x10 distributor
ELPRO Video Labs s.r.l. 7
Str.da della Pronda, 45/B 10142 TORINO - ITALY Tel.+39 0117701583 – Fax +39 011703751
SP205+
DUAL 1x5 VIDEO & AUDIO DISTRIBUTION AMPLIFIER
1
To use the unit as single 1 x10 distributor, proceed as follows: a) Make sure that all the units to be installed are OFF. b) Set the switch on the front panel to the “1x10” position remembering that this setting acts not only on the video but also on the audio. c) Connect the audio source to the AUDIO IN1 connectors. If the source is mono, only one of the two channels (L or R) can be used. As the AUDIO IN2 connectors are not active in this configuration, their connection is not significant. d) Connect the destinations to the AUDIO OUT1 and AUDIO OUT2 connectors. e) Power the SP205+ and other system units.
ELPRO Video Labs s.r.l. Str.da della Pronda, 45/B 10142 TORINO - ITALY Tel.+39 0117701583 – Fax +39 011703751
8
SP205+ 4.0
DUAL 1x5 VIDEO & AUDIO DISTRIBUTION AMPLIFIER
TECHNICAL DATA
4.1 Video Input type Input ret.loss Input level Output gain Output ret.loss Frequency response Delay Differential gain Differential phase Hum & noise Crosstalk Hum & noise
AC coupled 32 dB @ 5 MHz worst case Max 2 Vpp on 75Ω 0 dB 44 dB @ 5 MHz worst case 0.10 dB @ 9 MHz 0.15 dB @ 10 MHz ±3 dB @ 120 MHz 18 ns 0.3% 0.2° -84 dB unweighted 45dB (two sections) @5MHz, worst case -84 dB unweighted
4.2 Audio Input Input impedance Input level CMRR Output impedance Output gain
AC coupled 56KΩ +10dBm Max 36dB at 5KHz 150Ω 0 dB
Frequency response
±0.10 dB ± 3 dB
Harmonic distorsion
<0.05%@ 10dBm
Hum & noise Crosstalk
-74 dB unweighted 54 dB (two sections) at 16KHz worst case 51 dB (left/right) at 16KHz worst case
ELPRO Video Labs s.r.l. 9
Str.da della Pronda, 45/B 10142 TORINO - ITALY Tel.+39 0117701583 – Fax +39 011703751
from 7 Hz to 330 KHz up to 6MHz
SP205+
DUAL 1x5 VIDEO & AUDIO DISTRIBUTION AMPLIFIER
1
4.3 General characteristics Main input Power consumption Size (WXDXH) Weight Operating temp. Range Safety EMC
230Vac 5VA 483x149x44mm 2.0Kg 0 ÷ 45°C according to EN 60065 according to EN 55103-1 and EN 55103-2
Mark
5.0 NOTES This product is warranted for 5 years from the date of purchase. If the fault in the product is due to improper use or operations carried out by third parties, the warranty is forfeited. During the warranty period, Elpro will repair the faulty units free of charge. The faulty units must be sent CARRIAGE FREE to the Elpro offices in Turin with a regular accompanying note. The units repaired will be returned CARRIAGE FORWARD to the addressee. Outside the warranty period, Elpro will repair the faulty units EX its Turin offices, charging the cost of the repair to the customer.
For any problems during installation of the SP205+, call the Elpro hot-line Tel. +39 011 7701583 or e-mail:
[email protected]
ELPRO Video Labs s.r.l. Str.da della Pronda, 45/B 10142 TORINO - ITALY Tel.+39 0117701583 – Fax +39 011703751
10
