Transcript
(044)361-05-06
ICQ:495-089-192
(067)469-02-12
ICQ:613-211-859
(099)048-99-03 (093)672-77-76
User's Manual Car speakers DLS X-program X-SD52
In the online store Winauto you also can buy car acoustic DLS X-program X-SD52. Delivery in Kyiv and throughout Ukraine with payment upon receipt!
winauto.ua
Sale - Car Receivers - Facia Plates - Head Units - Car TVs and Monitors - Antennas - Car Audio - DVR - GPS Navigation - Trip Computers - Car Alarm Systems - Mechanical Locking - Parking Systems - Car Cameras - Xenon and Lights - Established Optics - Tuning - Car Heating and Cooling - Sound Marine and Electronics - Car Accessories - Isolation - Installation Components - Batteries, Power - Oils and Fluids -
Online-store car audio and autogoods Winauto For models: X-SA52 - 2-way 13 cm / 5,25” X-SA62 - 2-way 16,5 cm / 6,5” X-SB52 - 2-way 13 cm / 5,25” X-SB62 - 2-way 16,5 cm / 6.5” X-SC42 - 2-way 10 cm / 4” X-SC52 - 2-way 13 cm / 5,25” X-SC62 - 2-way 16,5 cm / 6,5” X-SP52 - 2-way 13 cm / 5,25” X-SP62 - 2-way 16,5 cm / 6,5” X-SD52 - 2-way 13 cm / 5,25” X-SD62 - 2-way 16,5 cm / 6,5”
X-PROGRAM Component systems Owners manual Thank you for buying an X-program speaker. Please read this manual before installing the speakers.
Installation
Bass driver: Normally they will fit in the factory pre-made mounting holes in the door or dashboard. If you want an improved sound, reinforce with a baffle of MDF-board or similar.
- Turn off the Audio System. It is also advisable to disconnect the negative (-) terminal of the vehicle battery. - Before cutting drilling, or inserting any screw, check clearances on both sides of the planned mounting surface. - Also check for any potential obstacles such as window tracks and motors, wiring harnesses etc. - Always wear protective eyewear. - Follow the instruction manual when connecting the crossover.
Running-in period
to .u
Tweeter: 1. Install the tweeter in the pre-made place in the door of your vehicle. 2. Or install the tweeter on the dashboard at the A-pillar facing inwards to a place between the front seats. 3. Or cut a hole in the door side using the mounting cup coming with the tweeter. Avoid placing tweeters where they will be blocked by objects in the interior of the car.
Getting started
a
Fasten the speakers properly in order to avoid bad sound or rattling. Use the screws coming with the speaker kit. If you feel the less unsure about how to do, let a professional installer do the job for you.
Allow the speakers to play for at least 15-20 hours. After this time the performance is correct.
Speaker phasing
in au
To be sure to have the correct speaker polarity (phase) you can check this by using a 1,5 Volt battery. Connect a cable from the battery plus-pole to the speaker plus, and a cable from the battery minus to the speaker minus. If the speakers are correctly connected the speaker cone should move outwards on both right and left channel. This check must be made on the cables going from the speakers, to the output terminals of your car stereo or amplifier.
w
Crossover box: Do not install the crossover boxes inside the doors, they can easily brake and moisture can damage the components. Make sure the cables don’t get jammed causing short circuit to ground. This can damage the output circuits of the head unit or amplifier. Fasten the box properly using wire ties or screws. Don’t place them close to the internal wiring of the car, this may cause interference. The crossovers must be used, if you connect without them the sound becomes bad and you will destroy the tweeters.
Technical Assistance For technical assistance ask the shop where the product was sold or the distributor in your very country. Information can also be found on our WEB-site www.xprogram.com We follow a policy of continuous advancement in development. For this reason all or part of specifications & designs may be changed without prior notice.
X-program is designed, engineered and distributed by:
DLS Svenska AB P.O. Box 13029 - SE-40251 Göteborg - Sweden Tel: +46 31 840060 - Fax: +46 31 844021 E-mail:
[email protected] www.xprogram.com X-program speakers are produced in Taiwan This product must be returned to the separate collection system for electronic products. Do not dispose this product together with general household waste.
Warranty service This speaker is covered by warranty, depending on the conditions in the country where it is sold. If the speaker is returned for service, please include the original dated receipt with the product.
Speaker facts for X-program 2-way speaker systems Model
Woofer size
Tweeter size
Nom. power
Peak power
Sensitivity
Magnet diameter
Installation depth
Mounting hole
Fs Hz
Qts
Vas litre
Z ohm
X-SA52 X-SA62 X-SB52 X-SB62 X-SC42 X-SC52 X-SC62 X-SP52 X-SP62 X-SD52 X-SD62
13 cm / 5,25” 16,5 cm / 6,5” 13 cm / 5,25” 16,5 cm / 6,5” 10 cm / 4” 13 cm / 5,25” 16,5 cm / 6,5” 13 cm / 5,25” 16,5 cm / 6,5” 13 cm / 5,25” 16,5 cm / 6,5”
28 mm / 1,1” 28 mm / 1,1” 28 mm / 1” 28 mm / 1” 16 mm / 0,6” 20 mm / 0,8” 20 mm / 0,8” 20 mm / 0,8” 20 mm / 0,8” 16 mm / 0,6” 16 mm / 0,6”
80 W 80 W 100 W 100 W 50 W 50 W 60 W 60 W 60 W 50 W 50 W
300 W 300 W 400 W 400 W 200 W 200 W 200 W 200 W 200 W 200 W 200 W
86 dB 86 dB 85 dB 91 dB 84 dB 85 dB 87 dB 85 dB 91 dB 86 dB 86 dB
100 mm / 4” 100 mm / 4” 100 mm / 4” 110 mm / 4,33” 70 mm / 2,75” 80 mm / 3,15” 90 mm / 3,54” 90 mm / 3,54” 90 mm / 3,54” 80 mm / 3,15” 80 mm / 3,15”
64 mm / 2,52” 73 mm / 2,87” 72 mm / 2,83” 72 mm / 2,83” 50 mm / 2” 65 mm / 2,56” 67 mm / 2,64” 47 mm / 1,85” 56 mm / 2,20” 53 mm / 2,08” 63 mm / 2,47”
120 mm / 4,72” 145 mm / 5,7” 120 mm / 4,72” 145 mm / 5,7” 102 mm / 4” 120 mm / 4,72” 145 mm / 5,7” 120 mm / 4,72” 145 mm / 5,7” 120 mm / 4,72” 145 mm / 5,7”
64,2 61,6 76,9 67,7 73,8 70,8 46,6 89,4 66,7 81,4 46,8
0,54 0,67 0,69 0,55 0,62 0,66 0,48 0,86 1,03 0,68 0,56
5,57 9,16 3,40 6,84 2,82 4,39 18,6 2,70 8,20 3,77 17,66
4 4 4 4 4 4 4 4 4 4 4
Online-store car audio and autogoods Winauto
+
-
+
Tweeter -
Black/ blue
+
Surface install:
+
X-SA52 X-SA62
Tweeter level select:
Woofer
+
Angled mounting: Put the cable through the hole in the rear end of the angled cup. The tweeter is attached to the cup by pressing them together. Attach the cup to the surface with the double adhesive tape.
Bass/mid
+ From head unit/amp. -
Select tweeter level by moving the jumper inside the filter box. All models have four different levels.
Red +
From head unit/amp.
Blue +
X-ST20 - tweeter installs Surface install:
to .u
Red +
X-SP52 X-SP62 X-SC52 X-SC62
w
+
Plain mounting: Use only the plain mounting cup (1) (it’s normally mounted at delivery). Attach to surface with the two screws or double adhesive tape. Angled mounting: Remove the plain mounting cup by bending with a small screw driver in the gap (A). Attach the tweeter element to the angled cup (2) as shown on picture 3. Pull the cable through the centre hole. Now the tweeter can be mounted in two different angles. Attach to the surface with the two screws or double adhesive tape.
Recessed install: Make a 48 mm / 1,89" hole in the door side panel. The installation becomes easier if the door side is removed from the door. Put the two metal wings through the two tracks in the centre of the cup, just as the picture shows, and attach them with the M4 2 screw and nut through the centre hole. Put the tweeter element into the cup with the cable going out through the bottom hole. Attach the tweeter element to the plain cup using the mounting ring (C) attached between the cup and the tweeter element. The metal wings (B) should be on the back side of the door panel, holding the cup in place. A
3
4
X-ST16 tweeter facts
Tweeter level select: For High level connect yellow and red wire. Disconnect for Low level
High pass
Black -
-
You need a hole with a diameter of 43 mm/ 1,7”. Put the two metal wings through the two tracks in the center of the cup, just as they lie picture, and attach them with the M4 screw and nut through the center hole. The cup is attached to the door side when the metal wings is pressed to the back side of the door. Put the tweeter into the cup with the cable going out through the bottom hole. Then attach by putting it into the cup.
Size Nom. power (RMS) Freq. range Sensitivity Magnet diameter Mounting depth Mounting hole Cone material
16 mm / 0,63" 50 Watts, 80 Watts max 2 kHz-20 kHz 91 dB 20 mm / 0,8" neodymium magnet 20 mm / 0,8" (recessed mounting) 43 mm / 1,7" (recessed mounting) Mylar
in au
Black -
Yellow Red
Cable filter High pass (red)
Low pass
Cable filter Low pass (blue)
Recessed install:
Black -
Blue +
2 1
a
X-SD52 X-SD62 X-SC42
Tweeter
Black -
X-SD52 X-SD62 X-SC42
X-ST16 can be mounted on the dashboard with the angled cup (1), or recessed in a doorside (3).
From head unit/amp.
Tweeter
+
X-ST16 - tweeter installs
-
-
+
-
Black
TW WF
Tw level
+1,5 0 -1,5 -3
INPUT
X-SB52 X-SB62 X-SP52 X-SP62 X-SC52 X-SC62
-
Silver Silver/red
+
+1,5 0 -1,5 -3
INPUT
Tw level
WOOFER TWEETER
Crossover connection
X-ST28 - tweeter installs
X-SA52 X-SA62 X-SB52 X-SB62
Surface install: For angled surface mount together with the angled cup: The tweeter is attached to the cup by pressing the two parts together. When removing the tweeter from the cup, just bend with a small screwdriver or knife in the notch.
1 A Surface install
Recessed install
Recessed install:
3
Make a 50 mm / 2" round hole in the door side panel. Attach the cup in the hole using the metal wing. The wing is screwed on the back with a machine screw M4 size and holds the cup in place. Put the tweeter into the cup with the cable going out through the bottom hole. Then attach the tweeter into the cup by pressing it inwards.
C B
X-ST20 tweeter facts
X-ST28 tweeter facts
Size Nom. power (RMS) Freq. range Sensitivity Magnet diameter Mounting depth Mounting hole Cone material
Size Nom. power (RMS) Freq. range Sensitivity Magnet diameter Mounting depth Mounting hole Cone material
20 mm / 0,8" 50 Watts, 80 Watts max 1,5 kHz-20 kHz 93 dB 20 mm / 0,8" neodymium magnet 22 mm / 0,87" (recessed mounting) 48 mm / 1,89" (recessed mounting) Silk
28 mm / 1,1" 50 Watts (80 Watts max) 1,5 kHz-20 kHz 93 dB 28 mm / 1,1" 21 mm / 0,83" (recessed mounting) 50 mm / 2" (recessed mounting) Hand treated fabric
