Transcript
Model 6721 PRO-FIT® 3672
Rectangular Air Massage Bath
Features • 71-1/2" x 35-1/2" x 20" Rectangular air massage bath • Powerful, single-speed blower and air switch for reliable operation • Heating element warms the air before it enters the bathing well through the perimeter channel • 20 minutes after the bath is turned off the motor automatically blows any remaining residue out of the “Quick Drain” air channel • Limited One-Year Warranty • Available in Standard Colors: white, almond, biscuit and bone
Model 6721 (Shown with metal air switch and Lift and Turn drain)
Options Lift and Turn Drain Model # Description PF1320 PF1321 PF1322 PF1323
Polished Chrome Everbrass (PVD) Brushed Nickel Oil Rubbed Bronze
Model # Description SWP150
Nailing flange kit
SWAP00
Factory installed nailing flange
PF1326A
6' Removable apron
Metal Trim Model # Description PF2335 PF2336 PF2337 PF2338
Polished Chrome Everbrass (PVD) Brushed Nickel Oil Rubbed Bronze
Printed in U.S.A. 12/12 © 2012 Mansfield Plumbing Products, LLC ® Pro-fit is a registered trademark of Mansfield Plumbing Products, LLC.
MADE IN USA Mansfield Plumbing Products LLC • Customer Service Toll Free 877-850-3060 • Fax 419-938-6234 Website: www.mansfieldplumbing.com • Email:
[email protected]
Model 6721 PRO-FIT® 3672
Rectangular Air Massage Bath
Specifications Model #
Description
6721
Codes/Standards
71-1/2" x 35-1/2" x 20" Rectangular Air Massage Bath
Specification
Description
Specification
Description
Material
Acrylic, fiberglass reinforced
Number of Jets
53
Construction
Self-contained, pre-plumbed air massage bath, mounted on a pre-leveled base
Water Capacity
27 gal. (min.) / 52 gal. (max.)
Blower Motor
120V, 60HZ, 6.0 Amp, Single Speed blower, 200 Watt Heater, Single Phase–Pre-mounted
Floor Loading Weight
47 lbs. / sq. ft. (229 kg/m2)
Electrical Requirements
120V, 15 Amp, GFCI protected
Shipping Weight
154 lbs.
On/Off Control
Air Switch
Warranty
Limited One Year
Technical Information 1 71 " 2 (1816 mm) 12" (305 mm)
PLUMBING ROUGH-IN 17 3 " 4 (451 mm)
STD
DRAIN
27 " (686 mm) 20 " (508 mm)
SLOPE
35 1 " 2 (909 mm)
1/4"/ Ft.
3 3/4" (95 mm)
Blower Location (Standard Only) Required Blower Motor Access 35 1/2" 20" W x 15" H
AIR SWITCH
48 " (1219 mm) 62 " (1575 mm)
(909 mm)
18 1 4"
(464 mm)
18 1 4"
20"
CENTER OVERFLOW
15 1 2"
(394 mm)
(464 mm)
(508 mm)
Note: Measurements may vary 1/4" (+/-) Note: If a factory installed nailing flange is added to a unit, add 1/8" to each side flanged.
Optional Removable Apron available.
These dimensions are nominal and subject to change without notice. When tested for compliance to the requirements of ASME A112.19.7M for “Whirlpool Bath Appliances” and ANSI Z124.1.2M “American National Standard for Plastic Bathtub and Shower Units”, the tested units are found to comply and are acceptable for listing under IAPMO R & T. Certified for permanent electrical connection only. Printed in U.S.A. 12/12 © 2012 Mansfield Plumbing Products, LLC ® Pro-fit is a registered trademark of Mansfield Plumbing Products, LLC.
MADE IN USA Mansfield Plumbing Products LLC • Customer Service Toll Free 877-850-3060 • Fax 419-938-6234 Website: www.mansfieldplumbing.com • Email:
[email protected]
