Transcript
RAVENNA® SEMI-PEDESTAL SINK
VITREOUS CHINA
RAVENNA® WALL-HUNG SEMI-PEDESTAL LAVATORY • Vitreous china • Contemporary design wall-hung with semi-pedestal P-trap cover for ease of cleaning • Rear overflow • Soap and accessory deck • Optional with integral mounted towel bar (ordered separately) • Supplied with mounting kit • Design matched to Ravenna toilets (faucet shown not included) • Faucet ledge with generous shelf area for accessories
❏ 0268.444 Faucet holes on 4" (102mm) centers ❏ 0268.888 Faucet holes on 8" (203mm) centers
(shown on rough)
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
❏ 0268.144 Center hole only Nominal Dimensions: 24-1/4" x 20" (616 x 508mm)
To Be Specified: ❏ Color: ❏ White ❏ Black ❏ Faucet*: ❏ Faucet Finish: ❏ Supplies: ❏ 1-1/4" Trap
Bowl sizes: 19-3/8" (492mm) wide 12" (305mm) front to back 6" (152mm) deep Separate Components: ❏ 0268.004 Lavatory slab 4" (102mm) centers ❏ 0268.008 Lavatory slab 8" (203mm) centers ❏ 0268.001 Lavatory slab center hole only ❏ 0044.000 Semi-pedestal leg
* See faucet section for additional models available
Recommended Components: ❏ 3520.000 Integral Towel Bar 002 Chrome, 295 Satin Nickel ❏ 738520-0070A Towel Bar mounting kit Compliance Certifications: Meets or exceeds the following specifications: • ASME A112.19.2 - 2008/CSA B45.1-08
© 2015 AS America Inc.
J71
spec_0268.888 Ravenna SemiPedLav Rev. B 8/15
RAVENNA® SEMI-PEDESTAL SINK
VITREOUS CHINA
0268.888 20-5/16" (516mm) 19-7/16" (493mm) 17-7/16" (443mm) 8" (203mm)
1/2" (13mm) 3" (75mm)
1-3/8" (35mm) 4-3/4" (120mm)
FINISHED WALL
8" (205mm) 1/2"D. (13mm) 1-3/8"D. (35mm)
20" (507mm)
4-1/4" (108mm)
24-1/4" (615mm) 9" (230mm)
Ø 7/8" (22 mm) HOLES FOR ANCHOR BOLTS 3" (76mm)
8-1/4" (209mm)
FINISHED WALL
7-3/8" (187mm)
18-3/8" (466mm) 17-5/16" (440mm)
20" (507mm)
1/2"D. (13mm) OPTIONAL TOWEL BAR
SUPPLIES AS REQUIRED 1-1/4" O.D. WASTE 1-1/4" O.D. TAILPIECE
34" (864mm)
FINISHED FLOOR
NOTES: DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE SUGGESTED. PEDESTAL ANCHORING SCREWS NOT INCLUDED. ■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST BE TAKEN FROM FIXTURE. FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS. INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY. IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
© 2015 AS America Inc.
J72
spec_0268.888 Ravenna SemiPedLav Rev. B 8/15