Transcript
MULTIPRON
E1, Gigabit Ethernet , RS232/485 Tester MULTIPRON
10/100/1000 Mbit/s Ethernet transmission data monitoring and analysis (two Gigabit Ethernet interfaces, 2x 100/1000Mbit/s SFP and 2x 10/100/1000Mbit/s RJ45)
Throughput, back-to-back, latency, frame-loss, recovery tests, as per RFC 2544 (unidirectional, bidirectional, loopback) , network sniffer, custom interface-to-interface tests
E1 (G.703/G.704) data monitoring and analysis (up to 4 E1 channels at the sime time)
Ability to send/receive standard PRBS test patterns, inject/monitor alarms or errors, monitor signal frequency
RS232 and RS485 transmission tests, two serial interfaces, up to 2Mbit/s transmission speed
LCD touch-screen
Additional battery power
MULTIPRON is a comprehensive test tool with E1, Gigabit Ethernet, RS232/485 link maintenance and failure diagnose. MULTIPRON is equipeed with two Ethernet interfaces, Ethernet traffic generator, four E1 interfaces and RS232/485 serial interface. Device is equipped with two Ethernet interfaces, each one realized by one electrical 10/100/1000 Mbit/s RJ45 port and one 100/1000Mbit/s SFP module. Ethernet data streams can be configured with frame sizes (up to 10240Bytes), burst sizes, interframe gap, MAC/IP addresses, VLAN (802.1q, QinQ), QoS options, UDP/TCP ports and others. MULTIPRON also performs E1 data monitoring and analysis. Usig MULTIPRON it is possible to test four E1 channles at the same time ( each channel via independent RJ45 port ). Extended version of MULTIPRON tester additionally allows user to perform data monitoring and testing of E1 channels timeslots (according to the ITUT G.704 Recommendation). Additional serial interfaces allow user to conduct RS232 or RS485 transmission tests. Basic version of tester is equipped with single simplified RS232 port. MULTIPRON_advanced version of the deivce is additionally equipped with full RS232 port and RS485 interface. Testers can generate RS transmission with maximum throughput of 2Mbit/s (RS485) and 230,4kbit/s (RS232). Color, high resolution touch-screen provides convenient test parameters settings and results displaying. Testers can be powered from 230V AC power supply or from battery with capacity of 18000 m
BITSTREAM
Specification can be changed due to device development
Ethernet Combo Gigabit Ethernet interfaces (2x RJ45 plus 2x SFP) allow user to test both wired and optical transmission paths. Tester supports few kind of tests on Ethernet interfaces: RFC2544, Network Monitor Test (shows Ethernet utilization) , Network Sniffer, custom interface to interface test and simple cable tester.
Network Sniffer test makes a copy of transmitted data without interrupting it. To sniff passing data user can connect PC with software sniffer (Wireshark etc.) to tester or used simplified built-in sniffer monitor.
BITSTREAM
Specification can be changed due to device development
E1 G.703/G.704 While using BitStream testers it is possible to test four E1 channels at the same time (each channel via independent RJ45 port). User is allowed to perform data monitoring and testing of E1 channels timeslots (according to the ITUT G.704). E1 test functionality includes the ability to send/receive standard PRBS test patterns, inject/monitor alarms (LOS, LOF, AIS, RDI, CRC4) or errors (bit, code, CRC4), monitor signal frequency and perform G.826 analysis. Tester is able to generate clock deviation in the range of +/- 30ppm.
„Out of service" tests (such as loopback and end-toend tests) allow user to verify the quality of the E1 transmission path before comissioning E1 services.
„In service" monitoring of E1 alarms and errors allow user to troubleshoot lines or equipment problems in live traffic. Errors can also be intentionally injected to examine system’s response.
RS232/422/485 Testers can be equipped with full RS232 interface, simplified RS232 interface and RS485 interface.
Devices are able to generate serial transmission with up to 230,4kbit/s (RS232) and 2Mbit/s (RS485) data rates
BITSTREAM
Specification can be changed due to device development
MULTIPRON is avaiable in two versions:
− basic - MULTIPRON_basic − advanced - MULTIPRON_advance MULTIPRON_basic basic verison
MULTIPRON_advance advanced version
Ethernet
Ethernet
• • • •
• • • • • • • •
Generates Ethernet traffic at any rate Frame size configuration VLAN configuration RFC 2544 tests Double VLAN (QinQ) configuration Configurable ”burst traffic” generation EtherType of a payload configuration Traffic statistics, network monitoring
• • • •
4 channels PRBS test patterns Clock source: internal or external (E1 channel) AIS, Loss of Frame and Loss of Signal alarm detection CRC4 and MF monitoring Selection of PRBS test patterns Selection of G.704 timeslots assigned for the monitoring channel operation Clock monitoring Up to ±50 ppm transmit clock deviation In-service monitoring ( LOS, LOF, AIS, MF, CRC4 etc. )
Generates Ethernet traffic at any rate Frame size configuration VLAN configuration RFC 2544 tests (simplified)
E1
E1
• • • •
4 channels AIS and Loss of Signal alarm detection PRBS test patterns Clock source: internal or external (E1 channel)
• • • • • • RS
RS •
• •
RS232 Configurable RS Port Settings BER monitoring
• •
• •
•
BITSTREAM
RS232 RS485 Configurable RS Port Settings BER monitoring Console terminal
Specification can be changed due to device development
PARAMETERS RS-232/RS-485 interface
Management
• Transmission speed: 0-115200 bit/s
Line interface 2048 kbit/s • • • • •
•
Weight < 1kg
6-inch LCD touch-screen
Ethernet Ports
ITU-T G.703 2048 kbit/s ± 50 ppm binary throughput 120 Ohm E1 impedance Line code HDB-3 Types of connectors: RJ-45
Dimension
•
• •
10/100/1000 Mbit/s transmission speed Supports VLAN / multiple VLAN, IEEE 802.1q, QinQ Proper connection signalling 2 x RJ-45 type connector, 2 x SFP
• •
Power • • • •
Supply voltage range 24 to 60V DC External power supply included 230VAC/48VDC Additional battery power Up to 10W power consumption
BITSTREAM Sp. z o.o. ul. Mełgiewska 7/9, 20-209 Lublin, Poland Tel. +48 81 743 86 43, Fax +48 81 442 02 98
[email protected] www.bitstream.com.pl
BITSTREAM
Specification can be changed due to device development
