Transcript
Velocitykvm-8
The Thinklogical™ Velocitykvm-8 Multi-Mode Fiber Optic System consists of a transmitter unit and a receiver unit connected by three multi-mode fiber optic cables (or by one to three optional single-mode fibers). The transmitter unit connects to the computer with standard cables and the receiver unit provides connections to the user interface devices. The Velocitykvm-8 supports PS/2, full duplex stereo audio, serial (RS-232), USB 1.0 (HID) device ports, USB 1.1 and USB 2.0 (high speed up to 480Mbps).
Multi-Mode Fiber Extension System – Dual-link DVI
QUICK START GUIDE Local Display
STEP 10: Turn on the Source (CPU) last. Verify that all system features are functioning properly.
7
STEP 7: (Optional) Connect your local monitor cable (not included) to the DualLink DVI OUT connector on the VelocityKVM Transmitter.
DUAL-LINK DVI OUT
8
10
L2
L1
STEP 8: If desired, connect your local keyboard and mouse by inserting the PS/2 or USB HID connectors into the VelocityKVM Transmitter’s local devices receptacles.
9
UPDATES
P S 2
LINE IN
HOST
U S B 1 .1
CP
USB 2.0 Audio OUT Audio IN PS/2 Keyboard PS/2 Mouse USB HID (Kybd/Mouse) USB 1.1 (Kybd/Mouse)
L2
L1
5 3 6
DUAL LINK DVI IN
STEP 6: A DVI-D dual-link cable (CBL000023002MR) is included. Connect it to the CPU DVI Video Card and the other end to the VelocityKVM Transmitter’s Dual-Link DVI IN connector.
Note: Be sure to leave adequate ventilation space on both sides of the units (2” minimum), especially if the units are being stacked
HID
MIC OUT
CLINK
4
L1
L2
CNTRL
DEV
USB HID
FROM CPU
100-240V-,0.5A, 50/60 Hz
T 2A ,250VAC
PS/2 Keyboard/ Mouse
STEP 4: Connect your MultiMode Fiber Optic cables between the Transmitter and Receiver units as shown. (1 to 3 Single-Mode fibers can also be used, depending on the model and required fiber length.)
1
USB 1.1
▲ Audio OUT Audio IN►
L1: Data Tx to Rx and Video 1 Primary L2: Data Rx to Tx L3: Video 1 Secondary
5
USB HID
STEP 5: Connect your KVM devices to the CPU using the cables supplied in KIT-000005-R.
STEP 1: Ensure that the POWER ON/OFF switch is in the OFF position (0) on both the Tx and Rx units. Connect the supplied AC Power Cords to both units and plug them into a standard AC supply. LEAVE BOTH SWITCHES IN THE OFF POSITION.
L3
VelocityKVM-8 Receiver VEL-U00M08-SCRX L2
PWR
L3
LOCAL
STEP 9: Turn the Transmitter unit ON.
Note: In order to id possible exposure avoid to laser energy, it is good practice to attach the fiber optic cables prior to applying power to the unit.
CAUTION! Replace with same type and rating fuse.
SER IAL PORT
L3 DUAL-LINK DVI OUT
DUAL-LINK DVI IN
FOL
USB HID Connector
VEL-U00M08-SCTX
VelocityKVM-8 Transmitter PWR
PS/2 Connector
L1
CAUTION! Replace with same type and rating fuse.
SER IAL PORT
L3
FOL
DVI OUT DDC
P S 2
LINE OUT
DVI OUT
MIC IN
USB 2.0
USB HID
U S B 1 .1
U P D HOST A T E S CNTRL 100-240V-,0.5A, 50/60 Hz
T 2A ,250VAC
USB or PS2
2 CONTENTS Upon receiving your Thinklogical™ Velocitykvm-8 Extender, you should DVI find the following items: Display · VelocityKVM Extender Transmitter Out DDC* · VelocityKVM Extender Receiver · 2 AC power cords, PWR-000006-R (International connections may differ.) · VelocityKVM Extender Cables: 1 DVI-D Male Dual-link Cable, 2 meters, CBL000023-002MR
STEP 2: Connect your desktop devices (monitors, keyboard, mouse, etc.) to the Receiver using standard cables.
DVI Display Out
1 Cable Kit (8 six ft. peripheral cables.) KIT-000005-R
All physical connections to the product use industry-standard connectors.
3
* Display Data Channel: Communicates supported display modes to the CPU. This is the PRIMARY DISPLAY and should be used when only one monitor is connected. When 2 monitors are used, the display modes of both DVI outputs will follow the DDC of the primary monitor.
RACK-MOUNT OR DESK-TOP OPTIONS: Like all Thinklogical™ KVM extenders, the VelocityKVM-8 can be mounted in a standard EIA 19" rack or on a shelf or desk-top.
PHONE: WEBSITE: EMAIL:
1-800-291-3211 www.thinklogical.com
[email protected]
Velocitykvm-8
Each mounting bracket is secured by four screws and can be safely removed from the transmitter or receiver unit for desk-top mounting.
Visit us online at www.thinklogical.com for more product information, current updates and the complete line of Thinklogical products.
Copyright c 2009. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
8 Mounting bracket screws
Single Head Single Link Fiber Optic Transmitter
VELOCITY-8_Quick_Start_Rev_C
TM
STEP 3: Turn the Receiver unit ON.
2 Mounting bracket screws in four places.
