Transcript
LightwaveRF
connect 1 Gang 1 Way Dimmer 250w Operation Manual Model No: JSJS LW250 It is important to install this product in accordance with the fitting instructions below. Failure to do so may render your guarantee void. IMPORTANT: PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE AND FOR GUIDANCE ON THE ASSOCIATION OF REMOTE HANDSETS. FOR HELP AND SETUP GUIDANCE PLEASE VISIT www.lightwaverf.com
OVERVIEW:
Blue LED ‘ON’
Amber LED ‘OFF’
FITTING AND WIRING INSTRUCTIONS: Important Things to Consider Before you Begin 1). Before commencing work, ALWAYS isolate the mains power supply and remove the fuse in the fuse box or switch off the circuit breaker in the consumer unit. 2). If unit is to be used as a replacement for an existing product, remove existing unit from its location and disconnect the wiring. Ensure that the wall (back) box has a minimum depth of 25mm. 3). Certain items in the range will not fit into a 4-lug box. If such a box has been previously installed the North-South lugs should be removed or bent back to avoid contact with the new product. 4). Connect the wires as shown in appropriate wiring diagrams. Use green/yellow sleeving on any earth conductors not insulated. Ensure terminals are properly tightened and no bare wire is visible. When mounting products into mounting boxes make sure conductors are not trapped. 5). When screwing the unit to the mounting box, do not over-tighten fixing screws. Fixing screws are supplied with this product. 6). To reduce the risk of discolouration or tarnishing, avoid installation on wet plaster. 7). Products must be installed in accordance with the latest building and IEE wiring regulations. If in any doubt, please contact a qualified electrician.
Compatibility The LightwaveRF Slave Dimmer is compatible with: • Standard mains voltage incandescent & low energy incandecent lighting (min 40W, max 250W) • Dimmable Electronic Low Voltage Transformers • GU10 and equivalent HI spot mains halogen bulbs The 1 gang LightwaveRF Slave Dimmer is NOT compatible with: • Wire-wound transformers (generally older models) • Electric Motors Please Note: • Master units must be installed • Units can ONLY be operated manually: the slave unit will not operate with a LightwaveRF RF remote. For a full, up to date list of all compatible bulbs, including LEDs and CFLs, please refer to www.lightwaverf.com. Installation Guide 1. Turn off mains electrical supply. 2. Ensure that the wall (back) box has a minimum depth of 25mm. 3. Remove the existing light switch and disconnect the wiring. 4. Gently remove plate by inserting a flat screwdriver into the slots/s of the plate and lift away from the unit.
5. Strip the cable as shown then connect the wiring as per the diagrams below, ensure terminals are properly tightened and no bare wire is visible.
Max: 8mm Min: 13mm
Additional slave units (maximum of 6 in line) will allow for 2-way / multi-way operation (units can only be operated manually).
2-Way Switching
Multi-Way
6. Screw the dimmer switch to the mounting box and ensure that the screws are sufficiently tight to support the product, but please do not over tighten as this may cause some damage. Ensure that the plastic spacer is correctly aligned and that no wires are trapped between the dimmer switch and the back of the wall box.
7. Replace the plate – a ‘click’ sound should be heard to signify that the plate has been correctly replaced.
OPERATION: Please Note: • At least one master unit must be installed in order for slave unit to operate. • The LED indicators on master unit and slave unit flash simultaneously. Switch ‘ON/OFF’ Manual ‘ON’ Button Press once to switch ‘ON’ (Blue LED indicator will illuminate). Manual ‘OFF’ Button Press once to switch ‘OFF’ (Amber LED indicator will illuminate).
Dimming Control on the Receiver Lowering Dim Level 1. Make sure the light is switched on. 2. Hold down the ‘OFF’ button. 3. After 1 sec. the light will start to dim down. 4. At the desired brightness level release the ‘OFF’ button. NOTE: If the ‘OFF’ button is not released, the light will continue to dim until no light is emitted and stop, although the switch remains on, illustrated by the illuminated blue LED. Raising Dim Level 1. Make sure the light is switched on. 2. Hold down the ‘ON’ button. 3. After 1 second the light will start to become brighter. 4. At the desired brightness release the ‘ON’ button. NOTE: If the ‘ON’ button is not released, the light level will increase until it stops at the maximum possible level of brightness. If after setting a dim level the light is then switched off, the next time the light is switched on the light level will automatically return to the same setting.
SPECIFICATION (per module): Input rating: 220-240V~ 50Hz. Output rating: 40~250W Max. Incandescent lamp, 200VA Max. Low voltage lighting electronic transformers. Manual ON/OFF with dimmer function.
Birmingham Science Park Aston Faraday Wharf Holt Street Birmingham B7 4BB Tel: 01902 500 562 Email:
[email protected]
