Transcript
KTD-404 Controller Keypad Installation and Operations Guide
Operation NOTE:
Key Layouts NOTE:
KTD-404 Key Layout
A KTD-404 series keypad can address and control 512 P/T/Z receiver sites, operate a matrix switcher with 64 monitor outputs, address and select views from 64 multiplexers, and provide management of access control points. VCR control is only possible from the KTD-400 keypad. Figures 44 and 45 display key layouts for the KTD-404 and KTD-304R respectively. Description and operation of each key is presented on the following pages. The preset and annunciation options referred to in this chapter will function only if activated during KTD-404 setup.
Figure 44: KTD-404 Key Layout
Video Switcher Control Keys
Access Control Keys (& Special Application) Pan/Tilt/Zoom Control Keys
Site Select Keys
Multiplexer Function Keys
KTD-304R Key Layout
Figure 45: KTD-304R Key Layout Multiplexer Function Keys
Pan/Tilt/Zoom Control Keys
D0404SG0_B
Special Application Key
Video Switcher Control Keys
Site Select Keys
Access Control Keys
Special Application Keys
21
KTD-404 Controller Keypad Installation and Operations Guide
Key Functions
Site Select Keys -
0
9
Used for camera and monitor selection in DIGIPLEX operation mode, or camera and multiplexer selection in multiplexer operation. Also used for preset position selection when applicable. Refreshes alphanumeric display on the selected monitor. Also used to clear infinite alarms using numerical keys.
clear
Used in combination with 0 through auto to engage the preset tour mode.
set
9
to find preset positions. Also used with
Pan/Tilt/Zoom Control Keys zoom in
,
zoom out
focus near
,
focus far
iris open
,
iris close
Used to control the zoom function of the selected receiver sites motorized lens. Used to control the focus function of the selected receiver sites motorized lens. Also used to disengage the autofocus feature on the CyberDome. Used to control the iris function of the selected receiver sites motorized lens. Also used to toggle between on/off when Backlight Compensation is enabled.
Joystick Used to move the selected receiver sites camera up, down, left, or right in P/T
operation. Used to select views for multiplexer operation. Places the selected receiver sites pan/tilt unit in the auto pan mode (camera pans left and right automatically). Also used in combination with set to initiate the preset tour mode.
auto
auto focus
Engages auto focus mode on the CyberDome.
Video Switcher Control Keys mon
Used in combination with the number keys (0-9) to select an active monitor.
seq
Used to select sequence tour on active monitor. Toggles the active monitor between the alarm on and alarm off modes.
alarm
Access Control Keys open
1st
,
close
Used to operate the selected receiver sites door, gate, or turnstile access control. Used in access control applications to automatically select camera sites in the order in which they call in. This key will function only when the keypad has been programmed for annunciation.
Special Application Keys face
badge
22
Used to select KTR-11 Face/Badge Readers face camera. Used to select KTR-11s badge camera (or inserted badge view, if applicable).
D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
door1
, door2 Used to select auxiliary camera views from KTR-11s video switcher circuitry.
open 1
,
open 2
Used for two-way audio communication with selected site, when applicable (KTD404A and KTD-304RA only).
talk
vol
NOTE:
Used to operate the selected receiver sites door for access control.
vol
Used to adjust audio level on KTD-404A or KTD-304RA.
The volume level at each audio site is stored in the memory of the 304RA and 404As memory; when the site is called at a later date, it will not need to be adjusted again.
Multiplexer Function Keys NOTE:
The following keys may function differently, or not at all, on some models of multiplexers.
alt
Toggles the keypad between DIGIPLEX and multiplexer view control modes. This is the
key on the KTD-304R.
run
Selects automatic switching of videos in lower right window of current view; also used in setup of motion detection areas.
sel
Used to select an active multiplexer.
zoom
Toggles between a full screen view and a 2x view of the selected video, if available on the specific multiplexer.
live
Used to view the live video inputs in any of the display modes; also used during setup of motion detection areas
vcr
Selects VCR output for monitoring during taping or VCR input for viewing during playback. Also used in setup of motion detection areas.
full
Used by some multiplexer types to restore full view.
view
D0404SG0_B
mplx
Toggles between selected views.
23
KTD-404 Controller Keypad Installation and Operations Guide
Keypad Operation
When power is first supplied to a KTD-404 series keypad, the LCD display will briefly display the words Controller Keypad or the keypad type and then appear as shown below: Figure 46: KTD-404s Normal Operating Display
CAMERA 000 MONITOR 01 From this display and by observing the systems monitors, the operator uses the function keys for control. If the annunciation feature has been activated, the display will also show an empty call-in queue. Figure 47: KTD-404s Normal Operating Display with Annunciation
CAM 000 MON 01
1ST 2ND 3RD
Monitor Selection To select a monitor, press
mon
and use
0
through
Example: To select Monitor 12, press
mon
to enter the desired number.
9
,
,
1
2
All video switching operations will now be performed on the selected monitor. Camera Selection To select a camera, use
0
through
9
to enter the desired number.
Example: To select Camera 345, press
,
3
4
,
5
The camera associated with the site will appear on the selected monitor, and all keys applicable to that site will become operational (e.g., pan, tilt, zoom, etc.). Engaging Auto Focus on CyberDomes To engage auto focus on CyberDomes, press
auto focus
. Use
focus near
or
focus far
to disengage.
Finding a Preset To find a preset, select the desired camera, press set and use 0 through 9 to enter the preset number. The entry may be one or two digits depending on the largest preset position programmed in the keypad setup. Example: To find preset 6, press NOTE:
set
,
6
.
The preset option referred to in this chapter will function only if activated during KTD-404 setup. Preset Tours To activate a cameras preset tours or ShadowTour, select the desired camera and press set , auto , and the tour number (1-4). On older models of the CyberDome, only one preset tour could be programmed. Entering any tour number will activate the preset tour. To deactivate the tour, nudge the joystick.
24
D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
Camera Sequencing To place a monitor in the sequence mode: Select the monitor, and press display window:
seq
. The following display will appear in the keypads
Figure 48: Sequence Selection
ENTER SEQUENCE NUMBER? = (1-7) Use
1
through
4
to enter the desired sequence tour.
Setting Electronic Auto Pan Limits for Kalatel Domes To set the electronic auto pan limits on Kalatel dome receivers, first position the dome at the limit. While holding down the zoom and zoom out keys, move the joystick in the direction of the limit in being set. Example: To set the left limit, move the dome to the position of the desired left limit. While holding down the zoom and zoom out keys, move the joystick left . in Video Alarms To place a monitor in or remove it from the alarm mode, select the monitor and press alarm . Each time alarm is pressed, it either places the monitor in, or removes it from, the alarm mode. When a monitor is in the alarm mode, an A appears on the monitor screen. In this mode, the monitor will automatically call up alarmed sites. Figure 49: Monitor Screen with Alarm Mode Enabled
NOTE:
A monitor will only respond to alarms if it is in the alarm mode. A manual video call up will take a monitor out of the alarm mode. Clearing Alarms In a DIGIPLEX system, alarmed sites can be programmed to remain on the monitor screen indefinitely, and must be cleared by the operator. To clear the alarm, press clear and use 0 through 9 to enter the site number. Example: To clear alarm site 22, press
D0404SG0_B
clear
,
0
,
2
,
2
.
25
KTD-404 Controller Keypad Installation and Operations Guide
Annunciation When the KTD-404 keypad is programmed for site annunciation, it will stack as many as 32 call-in requests in the order in which they were received. The numbers of the first three sites appear in the keypads display window. Figure 50: KTD-404s Normal Operating Display with Annunciation
CAM 000 MON 01
1ST 2ND 3RD 001 123 354
1) To call up the first site, press 1st . The site will be removed from the queue, and waiting requests will move up in order. 2) To call up any site in the queue, use 0 through 9 to enter the site number. The site will be removed from the queue, and later requests will move up in order. NOTE:
If an annunciation call is received, a tone will sound every 15 seconds until cleared by the operator. In multiplexer mode, a tone will sound every 5 seconds. Two-Way Audio To establish two-way audio communication with a site, use 0 through 9 to enter the site number. Use the volume keys to adjust the audio level. Press talk to speak to the site.
NOTE:
When used with a KTD-336, set the attenuation jumpers on the Audio Card to the On position. Standard setup (system hard-wired) should maintain the attenuation jumper in the Off position. See figure 51 for location of the attenuation jumpers.
Figure 51: Audio Card Attenuation Jumpers
Attenuation Jumpers
Multiplexer Operation
26
The alt key toggles the KTD-404 between the normal operation mode and multiplexer operation mode.
D0404SG0_B
KTD-404 Controller Keypad Installation and Operations Guide
Switching to Multiplexer Control Mode To enter the multiplexer operation mode press the will appear:
key once and the following display
alt
Figure 52: Multiplexer Operation Mode
MULTIPLEXER 01 VIEW -The keypad is now able to control multiplexers. Selecting an Active Multiplexer Press the to control.
sel
key followed by the number keys to enter the multiplexer number you wish
Example: To select multiplexer number 12 press
sel
,
1
,
2
.
Calling up a Video Input on an Active Multiplexer Once the desired multiplexer has been selected, enter the video input number desired by using the number keys 0 - 9 . Example: To call up video input number 9 on the active multiplexer, enter Selecting Multiple Camera Views on a Multiplexer
0
,
9
.
Switching a Multiplexer to Live Video Press the
live
key to place the active multiplexer in the live video mode.
Placing the Multiplexer in the Camera Sequence Mode Press the
run
key to place the active multiplexer in the video sequence mode.
Viewing VCR Output or Playback. vcr Press the key to view the output for the VCR during recording or playback from the VCR during review of the VCR tapes.
Operating Electronic Zoom For multiplexers equipped with zoom capability, the zoom key will switch the multiplexer to this mode. While viewing in this mode, the joystick is used to move the zoom area within the image. (Electronic Zoom may vary according to the model of multiplexer.) Press the view key to step the active multiplexer between those views programmed to be available for that multiplexer. Each time the view key is pressed, the next available view will be displayed by the multiplexer.
D0404SG0_B
27
KTD-404 Controller Keypad Installation and Operations Guide
28
D0404SG0_B
