Transcript
IONTO-COMED INSTRUCTION MANUAL IONTO-COMFORT XDREAM BED Art. No. 8461, 8461.5
Contents Safety Instructions .......................................................................................................3 Fields of Use................................................................................................................4 Control Elements and Connections .............................................................................4 Installation ...................................................................................................................5 Operation.....................................................................................................................7 Set Reclining Position ............................................................................................. 7 Set Upholstery Heating (optional) ........................................................................... 8 Cleaning and Care.......................................................................................................8 Repairs and Servicing .................................................................................................9 Fault Finding and Solutions .........................................................................................9 Technical Data.............................................................................................................9 Transport/ Storage/ Operating Requirements............................................................10 Disposal.....................................................................................................................10 Delivery Contents ......................................................................................................10 Accessories ...............................................................................................................10 This instruction manual contains information intended to ensure safe operation of the treatment bed. Always keep it in close proximity where it is readily available for every user.
© IONTO-COMED 2010 IONTO-COMED GmbH Durlacher Allee 109 D-76137 Karlsruhe Telephone +49 (0) 721 / 97 70-0 Telefax +49 (0) 721 / 97 70-290 Email:
[email protected] http://www.ionto.de
2
© by IONTO-COMED
Safety Instructions
Before installing and using the treatment bed, carefully read the instruction manual and ensure that all directions and instructions contained are fully understood. It includes important safety information for installation, operation and maintenance! If the bed is used for any purpose other than that for which it was designed and as described in this instruction manual, such use will invalidate the manufacturers warranty and guarantee! The control unit may only be opened by the manufacturer or by an expert approved and authorised by the manufacturer. When unpacked, check the contents of the delivery to ensure that all parts have been included and that nothing has been damaged during transit. In the event of any doubt, please contact our customer service department. Never use the bed with a damaged mains power supply cable. Do not jam or kink the cable and do not allow it to rest on any hot object (e.g. radiator, lamp, etc)! If the mains cable is damaged in any way, immediately disconnect the bed from the mains power supply. Please consult our customer service department before using again. Before connecting to the mains power supply ensure that the voltage (V) shown on the type plate corresponds with the power supply available! Under no circumstances may the mains plug be disconnected from the socket with wet hands. Never attempt to remove the plug from the socket by pulling the connecting cable! Do not use in damp surroundings and do not splash with liquid! In the event of any liquid or foreign body entering the inner of the control unit, immediately disconnect the bed from the mains power supply! Please consult our customer service department before using again. Always isolate from the mains power supply by disconnecting the mains plug before cleaning!
© by IONTO-COMED
3
Fields of Use The IONTO-COMFORT XDREAM treatment bed is a fully automatic treatment bed with an excellent massage adequacy. Seat height, tilt angle, backrest and leg-rest can be adjusted by using four powerful motors. The settings are made with a manual control. The padding is breathable and easy to clean. Head and footrest are extendable. The lowest seat entry as well as the tiltable arm rests offer a comfortable entry to the treatment bed. The bed is available either with or without seat heating. The IONTO-COMFORT XDREAM treatment bed can be used for all types of cosmetic treatment as well as for massage. The client can lay in the prone position, either on the stomach or back.
Control Elements and Connections Legend (1) (2) (3) (4) (5) (6)
1 2 3 4
Headrest Backrest Armrest Seat Legrest Footrest
5 6
Fig. 1: IONTO-Comfort Xdream Bed
4
© by IONTO-COMED
11 7 12
8 9
13
10
Fig. 3: Seat Heating Control
Fig. 2: Manual Control
Legend
Legend
(7) (8) (9) (10)
(11) ON/OFF Switch for seat heating (ON) (12) Increase heating temperature (+) (13) Lower heating temperature (-)
Backrest adjustment Seat angle adjustment Legrest adjustment Seat height adjustment
Installation 1. Install the treatment bed: ) Stand the bed on a firm, level underground. ) Insert the headrest into the mounting in the backrest. 2. Mount foot cover:
Fig. 4: Delivery status of the bed
Fig. 5: Positioning of the lateral foot cover
© by IONTO-COMED
5
Fig. 6: Expending rivets
Fig. 7: Insert rivet socket
Fig. 8: Press the rivet header in
Fig. 9: Press all of the rivet headers in
Fig. 10: Mounted foot cover
) Position the foot cover at the bed (Fig. 5). ) Pull the expending rivets apart. The expending rivets have a socket and a header (Fig. 6). ) Insert the rivet sockets into the cover. Start at the rear of the bed and hold the cover with one finger up to avoid cover cracks (Fig. 7). ) Press all the rivet headers into the rivet sockets. Hold the cover with one finger up to avoid cover cracks (Fig. 8 + Fig. 9). Foot cover is mounted. 3. Connect the treatment bed to the main voltage supply: ) Ensure that the mains power supply corresponds to the voltage (V) shown on the type plate. ) Plug the mains power plug into the mains socket. The treatment bed is now ready for use.
6
© by IONTO-COMED
Operation Caution! Risk of pinching! The arms of the client must remain on the couch during adjustment of the reclining position. Note Do not allow that oil or any care products come in contact with the upholstery because this can damage it. We recommend the use of an upholstery protection, e.g. a towelling cover. If oil comes in contact with the upholstery, remove immediately. Set Reclining Position 1. Armrest adjustment: Caution! Danger of injury! Do not allow the armrests to fall downwards.
2.
3.
4.
5.
6.
Both Armrests (3) can be folded backward. ) Raise the armrest lightly. ) Fold the armrest backward. Raise armrests: ) Lift the armrests. ) Fold the armrests back forward again. Headrest adjustment: The headrest (1) is removable and can be tilted to the front or back. ) Pull the headrest up vertically to the desired position. ) Push the headrest forward or backward into the desired position. Backrest adjustment: The tilting angle of the backrest (2) can be adjusted. ) Press the left button in the first row on the manual control (7) to lift the back rest up front. ) Press the right button in the first row on the manual control to lift the back rest back down. Seat height adjustment: The whole bed can be raised or lowered to the required height. ) Press the left key in the 4th row (10) on the manual control to raise the bed. ) Press the right key in the 4th row on the manual control to lower the bed. Seat adjustment: The tilt angle of the whole bed can be adjusted both forwards and backwards (4). ) Press the left key in the 2nd row (8) on the manual control to tilt the seat angle backwards. ) Press the right key in the 2nd row on the manual control to tilt the seat angle forward. Legrest adjustment: The legrest (5) can be adjusted independently of seat and backrest. ) Press the left key in the 3rd row (9) on the manual control to raise the legrest. ) Press the right key in the 3rd row on the manual control to lower the legrest. © by IONTO-COMED
7
7. Footrest adjustment: The footrest (6) can be extended. Note The footrest must be retracted when moving the bed into the entry seat height (lowest position). ) Pull out footrest until desired position is reached. ) Push footrest back in. Set Upholstery Heating (optional) 1. Switch the upholstery heating on: ) Press the ON key (11) to switch the upholstery heating on. The control panel is located at the right side of the outer part of the back rest. All blue LEDs (1-5) will light up. ) Set the required temperature with the (+/–) keys of the control panel. ) Press the (+) key (12) to increase the temperature. The blue LEDs of the (1-5) keys will light up step by step. ) Press the (–) key (13) to decrease the temperature. The blue LEDs (1-5) will extinguish gradually. Note For safety reasons, the upholstery heating will automatically switch OFF after 90 minutes of operation! The upholstery heating can be switched ON again directly. 2. Switch the upholstery heating off: ) Press the ON key (11) to switch the upholstery heating off. 3. Switch the treatment bed off: ) Remove the mains power plug from the mains socket.
Cleaning and Care Caution! Danger of electric shock! Disconnect from the mains power supply before cleaning. Note Do not use any solvents, chloride, polish, synthetic cleaning agents, wax polish, aerosol sprays or aggressive cleaning agents which could cause damage to the upholstery or the bed. Do not use any substances which contain oil or grease to clean the upholstery. The upholstery is not resistant to chemical cleaning or dry-cleaning methods. ) Clean the upholstery with a cloth and warm water. We recommend microfiber material (art. no. 8299.61) or a cleansing glove (art. no. 9168.9). ) Dry upholstery after cleaning. ) Remove any stains from the upholstery with a mild cleanser.
8
© by IONTO-COMED
) Remove obstinate stains with Incidin Foam (art. no. 4660). Carefully follow the Directions for Use. ) Clean the frame of the bed and the manual control with a lightly moistened cloth. Ensure that no water enters the control unit or the manual control. ) Wash the towelling cover at 60°C.
Repairs and Servicing Your treatment bed does not require any special servicing when used correctly and in compliance with the manufacturer’s directions and instructions. However, in the event of any problem arising, please contact our customer service department. Only persons authorised by the manufacturer may perform repairs. Any alterations or repairs performed by non-authorised persons will invalidate any guarantee, warranty or responsibility of the manufacturer. In addition, the safety of the treatment bed could be adversely affected.
Fault Finding and Solutions Fault Automatic adjustment of the bed doesn’t function.
Seat heating doesn’t function.
Cause
Solution
Voltage supply cable not Check connection of the connected correctly. mains power cable. Mains power plug must be firmly inserted. Socket defective.
Check the function of the socket with another electronic device (e.g. a table lamp).
ON key is not pressed.
Press ON key.
In the event of any other problem arising which is not dealt with above, please contact our customer service department (telephone number on the rear page).
Technical Data Article number: Operating voltage: Power: Maximum weight on seat: Dimensions:
Weight:
8461 (without seat heating) 8461.5 (with seat heating) 230 V~ / 50-60 Hz 110 VA 170 kg Width with arm rests: 780 mm Length: 1740 – 1980 mm Seat height: 570 – 870 mm Headrest: extendable about 120 mm, removeable Footrest: extendable about 120 mm 85 kg © by IONTO-COMED
9
Transport/ Storage/ Operating Requirements Transport only in the manufacturers original packaging. Transport and storage temperature: -20 °C to +50 °C Operating temperature: +10 °C to +40 °C Relative air humidity: max. 90 %, non-condensing To avoid the formation of condensation, abrupt changes of temperature should be avoided. Wait until the treatment bed has acclimatised to the ambient temperature before putting into operation.
Disposal Dispose of the packaging, treatment bed, upholstery and accessories in an environmentally friendly manner and in compliance with local regulations. All electrical and electronic products should be disposed of separately from the municipal waste. This crossed-out wheeled bin symbol on the product means the product is covered by the European Directive 2002/96/EC. The product should not be mixed with general household waste. There exists a separate collection system for these products. The correct disposal and separate collection of your old appliance will help prevent potential negative consequences for the environment and human health. It is a precondition for reuse and recycling of used electrical and electronic equipment.
Delivery Contents 1x Treatment Bed including Padding 1x Manual Control
Accessories Art. No. 4660 Art. No. 8299.61 Art. No. 8129.8 Art. No. 9168.9
Incidin Foam, 750 ml Mikrofiber Cloth Single-use Hygiene Clothes, 100 pcs. Single-use Cleaning Gloves, 30 pcs.
For details of further accessories, please refer to the current IONTO-COMED catalogue.
10
© by IONTO-COMED
EG-KONFORMITÄTSERKLÄRUNG / DECLARATION OF CONFORMITY gemäß den Bestimmungen der EG-Richtlinie über / in accordance with the EU-Directives for Elektromagnetische Verträglichkeit 2004/108/EG / Electromagnetic Compatibility Directive 2004/108/EC Elektrische Betriebsmittel zur Verwendung innerhalb bestimmter Spannungsgrenzen 2006/95/EG / Low Voltage Directive 2006/95/EC
Hersteller / Manufacturer: Adresse / Address:
IONTO-COMED GmbH Durlacher Allee 109 D-76137 Karlsruhe
Hiermit bestätigen wir, dass das Produkt / We certifies that the product Geräteart / Purpose of equipment:
Behandlungsliege / Treatment Couch
Gerätetyp / Type of equipment: IONTO-COMFORT XDREAM BED Artikelnr. / Article no: 8461, 8461.5 mit obengenannten EG-Richtlinien übereinstimmt / is in accordance with the said EU-Directives.
Karlsruhe, 2010-03-01
IONTO-COMED GmbH Manager
Martin La Fontaine
Printed in Germany-G8461-1.2-12/2010
IONTO-COMED GmbH Durlacher Allee 109 y D-76137 Karlsruhe Telephone: +49 (0) 721 / 97 70-0 y Telefax: +49 (0) 721 / 97 70-290 http://www.ionto.de y Email:
[email protected]
