Transcript
QUICKSTART “BASIC” GUIDELINES FOR STANDARD MODEL 6050/6100 - FOR GATES UP TO 10 FEET AND OPENING 90° Models 6050/6100 is intended for installation only on swing gates used for vehicles.
Pedestrians must be supplied with a separate access opening.
120 S. Glasgow Avenue Inglewood, California 90301
For safety and installation instructions, please refer to the Installation/Owner’s manual.
U.S.A.
Gate Bracket
Open Gate
e at Br t ke ac
e as
Chassis Ground
e at
G t ke ac
Br
Sh
A
ow
ad
.5”
Lo
Important: The elbow assembly must be in the correct position on the arms BEFORE cycling operator the first time.
op
4”
24
” 23”
Elbow Flange
B
Output Shaft
10”
18.5”
14”
Right Support Leg
Open Gate
Open Gate
Left Support Leg
Concrete
12”
Post Base
10”
Conduit
2.5” 12” 3”
Output Shaft Position
22”
Concrete Pad
Pad MUST be Level.
24”
3/8
Secure operator to the concrete pad with four (4) 3/8” x 3” sleeve anchors (not supplied).
ACwer Ponduit Co
uit
p
Loo
nd Co
1
we
rA
rm Crank Power Arm will remain stationary during manual gate movement.
2
Manual Release Arm Assembly and Gate Bracket Height
the of is h pt e De ncret by o c ined s rm ition e t de cond ocal l l soi and des. o gc ldin i u b
c
Jun
ith ”w 3/4 eeps Sw
s
oxe
B tion
Po
Arms and Operator MUST be level.
Gate Bracket
30” Crank Arm
5”
Flange 60” Connecting Arm
Varies with base used. Ground
Copyright 2016 DoorKing, Inc. All rights reserved.
Brass Bushing
Elbow Assembly
Crank Power Arm
Important: Adjust the locknut on the crank power arm so that it is snug against the washer, but will still allow the 30” crank arm to rotate with little force.
B
3. OFF 4. ON 5. OFF 6. OFF 7. ON (Single Operator) 8. ON (Tamper Protect)
SW 3 ON
Run conduit on the opposite side of the open gate for the post base.
3”
n
Co
nk
1 2 3 4 5 6 7 8
Post Base MUST be Level.
Pad Base
B
Pla
le igh xib it HVolt e l F du
m
2”
Conduit
6”
m
o ott
f te o
w Lo lt Vo
0 630
Cra
Ar
Post Base
24”
43”
D
k
26”
43”
A
an
Note: 2” thick gate Illustrated.
7
Cr
Mount the post base into the concrete before installing the operator.
90°
• NO AC power. • NO DC power (On select models).
0 #2 to #11 m Co to 7 1. elay t to # R l . 2 4 Vo 2 3.
C
Closed Gate
90°
11
ON
20
Using shadow loop and gate opening in direction shown. SW 4 Auto Close 1. OFF Timer 2. OFF 1 2 3 4 5 6 7 8
Output Shaft
Concrete Position
Closed Gate
High Voltage Conduit
DIP-Switch Settings
Safety Cover Elbow Assembly
Important: Elbow flange MUST be on the opposite side of the closed gate. Manually adjust the arms to get the correct open and closed positions BEFORE powering up the operator. Open/Close limits will be automatically set the first time operator is cycled.
115 VAC
HIGH VOLTAGE!
G B st Po
43”
37
Important: A straight line drawn from the closed gate bracket through the open gate bracket MUST intersect the operator output shaft.
DANGER
se Ba
Note: 2” thick gate Illustrated.
D
d Pa
90°
Tip: It is recommended that a surge suppressor be installed on the high voltage power lines. 115 VAC
Closed Gate
GATE OPERATOR MUST BE PROPERLY GROUNDED!!
Neutral
12”
op Lo
34”
High Voltage Connection
se er ev R
Operator Position
Adjust 1 to 23 sec.
1. OFF (Opening Counter-Clockwise) 2. OFF 3. OFF 4. OFF 5. OFF (Normal Reverse Function) 6. OFF 7. CLOSE Photo Beam REQUIRED 8. OPEN/CLOSE Edge/Beam (See other side)
Loop Detectors
C Not included - Refer to the Installation/Owner’s
manual and Loop Information Manual (available FREE from www.dkaccess.com) for more information on loops and loop detectors.
Radio Receiver
D Not included - Refer to a specific Radio Receiver
Manual (available from www.dkaccess.com) for more information on radio receivers and antenna installation. (See reverse side for wiring) 6050-066-G-2-16
QUICKSTART “BASIC” GUIDELINES FOR MODEL 6050/6100 - DIP-SWITCH AND WIRING REFERENCE Model 6050/6100 is intended for installation only on swing gates used for vehicles. Pedestrians must be supplied with a separate access opening.
#11 - Access Control Devices
For safety and installation instructions, please refer to the Installation/Owner’s manual.
ON
1 2 3 4 5 6 7 8
3
Exit Loop Port Output Full Open Input
6
Auto-Close Timer Not Used 3-Button Single Button
7
Dual Operators Single Operator
8
Tamper Protect
4 5
OFF ON OFF ON OFF OFF ON OFF ON OFF ON
Description
Relay activates when gate is open (Shadow loop setting when used). Relay activates when gate is not closed. Relay activates when gate is opening and open. Relay activates when gate is opening and closing. The output wired to terminal #12 becomes the output from the exit loop detector plugged into the EXIT Loop port. Normal Setting. Terminal #12 is a normal full open input. Auto-close timer is OFF. Manual input required to close gate. Auto-close timer is ON. Adjustable from 1-23 seconds to close gate. Leave in the OFF position. OFF when using a 3-button station (DoorKing 3-button control stations only). ON when using a single button control, terminals 13 &14 become a STOP input. Switch must be OFF when bi-parting (dual) gates are used. Switch must be ON for single operator. Tamper protect is OFF. Normal Setting. Tamper protect is ON. Operator will close gate when being forced open.
Every time the operator is powered up, the First open command will automatically set the open and close limits of the gate.
Switch
Function
Setting
Note: After a DIP-switch setting is changed, power must be turned OFF and then turned back on for the new setting to take affect.
SW 3 (Bottom 8 Switches)
Telephone Entry
1
Important: Controls must be installed
Stand-Alone Card Reader
ON
1 2 3 4 5 6 7 8
2
Secondary Gate Opening Direction
3
Not Used
4
Motor Control for Secondary Operator
5
Reverse Shadow Loop
6
Gate Overlap
7
Monitored Close Beam Monitored Edge/Beam
8
#12 - Safety Opening Device
OFF ON OFF ON
Switch is OFF when both primary and secondary operator motors are powered from main terminals 4 and 5. Applies to operators originally manufactured with 4501, Rev O boards or lower). Switch is ON when secondary operator motor is powered from the secondary motor terminals. Applies to operators manufactured with 4501, Rev P boards and higher, and all 4502 boards. Terminal 15 is a STANDARD Reverse input. Terminal 15 is a Shadow input. Gate will NOT stop during the close cycle. Primary and secondary operators start at the same time. Secondary operator starts 1-2 seconds prior to primary operator.
OFF ON OFF ON
No Photo Sensor connected to Aux terminal 7 and 8. Photo sensor is connected to Aux terminal 7 and 8 and monitored. (Close ONLY) No Edge or Beam connected to Aux terminal 9 and 10. Edge OR Beam is connected to Aux terminal 9 and 10 and monitored. (Open/Close)
OFF
ON
DoorKing ONLY
Com Com CLOSE Beam
Same as above, for secondary 6050/6100 ONLY. Leave in OFF position.
3-Button Station
1 amp max. 24 Volt
SW 4, switch 3 must be ON.
OFF
White Com
Potential Entrapment Area
Normally Closed (N.C.)
CLOSED gate
Potential Entrapment Area:
Potential Entrapment Area
Installation of MONITORED entrapment protection is REQUIRED or operator will NOT function. An OPTIONAL Expansion Kit (sold separately) will allow connection for additional devices. IMPORTANT: Photo sensors must use Normally Closed (NC) contacts with the beam set for light operate (relay activated when beam is not obstructed).
Open/Close Edge
10
13 14 15 16 17 18 19 Com
13
20 Com
4502-010 KEY SWITCH DATA
11 12
14 15
NO NC
1 2 3 4 5 6 7 8
SW 3
OFF
Power (24 Volt DC) and logic output. Power is shut off .5 sec. prior to gate starting and remains off while gate is opening and in the open position.
10 Access 11 Device Open 12 Safety Open
ON
ON
Green Close
Magnetic Lock
9
1 2 3 4 5 6 7 8
Opens Counter-Clockwise
ON
Opens Clockwise
1 2 3 4 5 6 7 8
1
Primary Gate Opening Direction
Red Open
2
24 VAC Power
ON
SW 4
6 7 8 9
a minimum of 6-feet from the gate or installed in such a way that the person using the control cannot come in contact with the gate or gate operator.
Stand-Alone Keypad
1
2 3 4 5
Key Switch
Note: All stand-alone and telephone entry devices must use a separate power source.
Description
24 Volt
Circuit Board Relay
U.S.A.
3-Wire Radio Receiver Limited to 250 ma. Relay
1 and 2
Setting
1-OFF 2-OFF 1-OFF 2-ON 1-ON 2-OFF 1-ON 2-ON
SW 4 (Top 8 Switches)
Com
Function
120 S. Glasgow Avenue Inglewood, California 90301
Coax Antenna Kit P/N 1514-073
Aux Terminal Monitored CLOSE Beam Common Monitored OPEN/CLOSE Edge/Beam Common
SW 4
Switch
Antenna mounted outside operator cover.
7 8 9 10
CLOSE Photo Sensor 7&8 SW 3 switch 7 MUST be ON.
Please refer to the Installation/Owner’s manual for complete installation instructions for entrapment protection devices.
Open Photo Sensor 9&10...OR.... OPEN gate
OPEN Beam
SW 3 switch 8 MUST be ON. Normally Closed (N.C.)
Mointored Sensor Note: Only 1 monitored Device can be connected to each input.
.......Reverse Edge 9&10 SW 3 switch 8 MUST be ON.
POWE
