Transcript
Data Sheet
SPH-16 SFP Patching Hub
• Converts 16 Fast Ethernet or Gigabit Ethernet copper ports to SFP sockets • Supports any third-party standard SFP device • Fully transparent Layer 1 wire-speed conversion eliminates store and forward delays • Provides fault propagation to LAN link
Converting Ethernet copper ports to SFP sockets
• Supports SNMP management to interface with I2C parameters of standard SFP devices
SPH-16 is a simple, smart and powerful patching hub that converts Ethernet copper ports to SFP sockets. The device can connect to any RJ-45 compatible switch and supports RAD’s System on an SFP family of products, MiRICi and MiTOP. It also supports standard SFP devices from any other vendor. SPH-16 can also be used as an Ethernet copper-to-fiber converter, with various fiber optic media, to extend the distance of Fast Ethernet and Gigabit Ethernet networks.
The device supports hot-swappable SFPs working at 100 Mbps and 1000 Mbps, as well as Ethernet copper ports working at 100 Mbps and 1000 Mbps. It also supports hot-swappable AC and DC power supplies. Auto-discovery of Fast Ethernet (100 Mbps) or Gigabit Ethernet (1000 Mbps) is supported. SPH-16 provides a flexible lower-cost alternative to being locked into purchasing expensive dedicated SFPs.
The Access Company
SPH-16 SFP Patching Hub
FAULT PROPAGATION
MANAGEMENT
DIAGNOSTICS
If a failure is detected on the SFP port, the fault propagation mechanism deactivates the Ethernet copper port.
The unit can be managed via:
FLEXIBILITY The SPH-16 ports can be used for any combination of 100 Mbps or 1000 Mbps fiber optic SFPs and the RAD products MiRICi and MiTOP.
•
ASCII terminal, for configuration and status
Comprehensive diagnostic capabilities include real-time major and minor alarms to alert the user to fault conditions.
•
PC running a WEB browser
POWER SUPPLY REDUNDANCY
•
Telnet host
•
SNMP-based network management station.
SECURITY SPH-16 supports the following security protocols, to provide a high level of communication security: •
SNMPv3
•
RADIUS authentication
•
SSL for Web-based management
•
SSH for Secure Shell communication.
Figure 1. LAN over PDH via System on an SFP
SPH-16 offers the option of redundant power supplies, increasing reliability. COMPACT SIZE The unit is supplied in a compact 19-inch 1U high enclosure.
Data Sheet
Specifications ETHERNET USER INTERFACE Number of Ports 16 Compliance IEEE 802.3 Type 100/1000 Mbps, autonegotiation, full-duplex, MDI/MDX crossover Maximum Frame Size 10,000 Line Impedance 100Ω Connector RJ-45, shielded SFP USER INTERFACE Number of ports 16 Data rate 100/1000Mbps Maximum Frame Size 10,000 Interface Type Giga SERDES or 100BaseFX Connector SFP-based, MSA compliant
MANAGEMENT PORTS Out-of-Band Ethernet Management Port Compliance: IEEE 802.3 Type: 10/100 Mbps, MDI/MDX crossover Maximum Frame Size: 1522 Connector: RJ-45, shielded Control Port Interface: RS-232 DCE Connector: DB-9, female Data rate: 9.6, 19.2, or 115.2 kbps INDICATORS Ethernet Copper User (per port) LINK/ACT (yellow) – LAN link and data activity status On: Ethernet link is up Off: Ethernet link is not up Flashing: Ethernet link is up and RX and/or TX frames are being transmitted 100/1000 (green) –100 or 1000 Mbps On: 1000 Mbps mode Off: 100 Mbps mode SFP User (per port) LINK/ACT (yellow) – Ethernet link integrity and data activity status On: Ethernet link is up Off: Ethernet link is not up Flashing: Ethernet link is up and Rx and/or Tx frames are being transmitted
Figure 2. Ethernet Copper to Fiber
Ethernet Management LINK/ACT (yellow) – LAN link and data activity status On: Ethernet link is up Off: Ethernet link is not up Flashing: Ethernet link is up and RX and/or TX frames are being transmitted 10/100 (green) –10 Mbps or 100 Mbps On: 100 Mbps mode Off: 10 Mbps mode GENERAL Power AC power supply: 100–240 VAC ±10%, 50/60 Hz DC power supply: 20–72 VDC Power Consumption (fully occupied) AC: 105 VA DC: 70 W Physical Height: 43.7 mm (1.7 in) 1U Width: 440 mm (17.3 in) Depth: 182 mm (7.2 in) Weight: 2.9 kg (6.4 lb) Environment Temperature: 0 –50°C (32–122°F) Humidity: Up to 90%, non-condensing
Data Sheet SPH-16 SFP Patching Hub
516-100-09/09 Specifications are subject to change without prior notice. © 1988–2009 RAD Data Communications Ltd. The RAD name, logo, logotype, and the terms EtherAccess, TDMoIP and TDMoIP Driven, and the product names Optimux and IPmux, are registered trademarks of RAD Data Communications Ltd. All other trademarks are the property of their respective holders.
Ordering SPH-16/#/RM
Legend #
Power supply: AC single 100 to 240 VAC DC single 20 to 72 VDC ACR dual 100 to 240 VAC DCR dual 20 to 72 VDC
RM Rack mounting equipment (Default=None): CT Cable tray with rack mount (19-inch non-ETSI) SUPPLIED ACCESSORIES AC power cord (with AC power supply only) DC connection kit (with DC power supply only) OPTIONAL ACCESSORIES RM-43 Hardware kit for mounting one SPH-16 unit in an ETSI rack (including cable tray) RM-43-19 Hardware kit for mounting one SPH-16 unit in a 19-inch non-ETSI rack (including cable tray) RM-43-19-H1 Hardware kit for mounting one SPH-16 unit in a 19-inch non-ETSI rack
International Headquarters 24 Raoul Wallenberg Street Tel Aviv 69719, Israel Tel. 972-3-6458181 Fax 972-3-6498250, 6474436 E-mail
[email protected]
www.rad.com
North America Headquarters 900 Corporate Drive Mahwah, NJ 07430, USA Tel. 201-5291100 Toll free 1-800-4447234 Fax 201-5295777 E-mail
[email protected]
Order this publication by Catalog No. 803815
The Access Company
