Transcript
IR Illuminator Brackets Mounting Installation Guide
P32-081020-000A A1
Mounting Installation Guide
Table of Contents 1. Introduction .............................................................................................3 2. Standard Wall Mount ..............................................................................3 3. Single L-Type Wall Mount ......................................................................4 4. Dual L-Type Wall Mount .........................................................................7 5. Pole Mount.............................................................................................10 6. Corner Mount ........................................................................................13
2
Mounting Installation Guide
1. Introduction This mounting installation guide is intended to provide installers with basic instructions of how to mount the High Power Intelligent IR Illuminator (hereafter referred to as the illuminator) using optional accessories from MESSOA. If you are using other specialized mounting accessories or tools, always refer to the instruction document supplied with that product. Note: Always use the screws as instructed by this guide to ensure proper installation.
This guide will describe the following mounting methods:
Standard Wall Mount
Single / Dual L-Type Wall Mount
Pole Mount
Corner Mount
Before Installation Before mounting the camera onto the bracket, please first secure the mount bracket of your choice firmly at the desired position to a solid surface using appropriate screws and plugs. Also make sure to route all the required cables properly.
2. Standard Wall Mount This mounting method requires no additional accessory. Use the guide pattern provided with the illuminator to drill holes on desired surface. Then mount the bracket of the illuminator using appropriate anchors and screws (not provided).
.
3
Mounting Installation Guide
3. Single L-Type Wall Mount Before beginning the following procedure, please make sure to have these items ready:
L-Type Single Wall Mount Bracket
Screw Set x 3
Guide Pattern
1. Use the guide pattern to drill holes on desired location. Then attach the bracket using appropriate anchors and screws (not provided). 2. Take the provided screw sets, remove the nut and the washer as shown in the figure.
3. Using provided screw sets, attach the illuminator above or below the bracket and adjust the angle as needed. When desired angle is achieved, fasten the washers and nuts onto the screw sets.
4
Mounting Installation Guide
4. The illustration below shows the examples of illuminator adjusted to desired angle. Note: When the illuminator is adjusted to a certain angel, only 2 screw sets will be needed to fasten the illuminator.
5
Mounting Installation Guide
Single L-Type Wall Mount Dimensions
”) 35 (0.
110mm (4.33”)
160mm (6.30”)
mm Ø9
92mm (3.62”) Ø111mm (4.37”)
”) 35 (0.
206mm (8.11”)
mm Ø9
110mm (4.33”)
160mm (6.30”)
Ø20mm (0.79”)
6
Mounting Installation Guide
4. Dual L-Type Wall Mount Before beginning the following procedure, please make sure to have these items ready:
L-Type Dual Wall Mount Bracket
Screw set x 4
Guide Pattern
1. Use the guide pattern to drill holes on desired location. Then attach the bracket using appropriate anchors and screws (not provided). 2. Take the provided screw sets and remove the nut and the washer.
3. Using provided screw sets, attach the illuminators above or below the bracket and adjust the angle as needed. When desired angle is achieved, fasten the washers and nuts onto the screw sets.
7
Mounting Installation Guide
4. The illustration below shows the examples of finished installations.
8
Mounting Installation Guide
Dual L-Type Wall Mount Dimensions
m( 0.3 5"
)*4
Ø3
110mm(4.33")
Ø9 m
m 8m
260mm(10.24")
228mm(8.98")
( 1. 5" )
165mm(6.5") 350mm(13.78") 160
o
270
.3 5") m (0
*2
204mm(8.03")
Ø 9m
o
70mm(2.76")
9
50mm(1.97")
Ø9mm(0.35")*2
Mounting Installation Guide
5. Pole Mount Before beginning the installation, please make sure to have these items ready:
Pole Mount Bracket
Screw set x 4
Metal strap x 2
Optional brackets for use with the pole mount bracket:
Single Wall Mount Bracket
Dual Wall Mount Bracket
(with screw set x 3)
(with screw set x 4)
1. Thread the metal strap through the holes on the bracket and then tighten screws on the strap.
3. Take the provided screw sets, remove the nut and the washer.
10
Mounting Installation Guide
4. Option 1: Mount the illuminator directly to the bracket using the screw sets.
4. Option 2: Attach the single wall mount bracket to the pole mount bracket using the screw sets. Then mount the illuminator to the bracket using the screw sets.
5. Option 3: Attach the dual wall mount bracket to the pole mount bracket using the screw sets. Then mount the illuminators to the bracket using the screw sets.
11
Mounting Installation Guide
Pole Mount Bracket Dimension 165mm(6.49")
Ø9mm(0.35)x10
Ø40mm(1.57”)
110mm(4.33")
72mm(2.83")
260mm(10.23 ")
94mm(3.7")
101.6mm(4.0") 238.4mm(9.38") 20mm(0.79")
36.9° 20mm(0.79")
3.2mm(0.12")
20mm(0.79") 20mm(0.79")
59.76mm(2.35") 6mm(0.24") 3.5mm(0.14")
12
Mounting Installation Guide
6. Corner Mount Before beginning the following procedure, please make sure to have these items ready:
Corner Mount Bracket
Screw set x 4
Optional brackets for use with the pole mount bracket:
Single Wall Mount Bracket (with screw set x 3)
1. Attach the bracket using appropriate anchors and screws (not provided). 2. Take the provided screw sets, remove the nut and the washer.
13
Dual Wall Mount Bracket (with screw set x 4)
Mounting Installation Guide
3. Option 1: Mount the illuminator directly to the bracket using the screw sets.
4. Option 2: Attach the single wall mount bracket to the pole mount bracket using the screw sets. Then mount the illuminator to the bracket using the screw sets.
5. Option 3: Attach the dual wall mount bracket to the pole mount bracket using the screw sets. Then mount the illuminator to the bracket using the screw sets.
14
Mounting Installation Guide
Corner Mount Bracket Dimensions
15
