Skeye Dart Ce Quick Start Guide

Transcript

Version 1.2 www.skeye.com Tel. +49 511 6102-0 Fax. +49 511 6102-411 Mail. [email protected] Web. www.skeye.de Serviceline. +49 1803 232829 (0.09 EUR per min. within Germany) Höft & Wessel AG Skeye Rotenburger Str. 20 30659 Hannover Contact: HW 90240 skeye.dart Quick Start Guide Views and Functions Loudspeaker Stylus Loudspeaker LEDs Imager/Camera Locking mechanism Storage battery Display Charging contacts Scan key Reset key Scan key Cursor keys Show/Hide touch / keypad field DC 1-Wire GND ENTER key Scan key Microphone Power supply unit port System interface Headset port Imager/Camera pane ESC key Start button Standby (press about 5 s) Activate Backup Battery Starting a GPRS connection* Upper edge (display) Lower edge In the battery compartment, push the switch of the backup battery (
) towards the display using the stylus. 1. 2. 3. Prerequisite: a SIM card is inserted. Switch the device on. Please check if the GPRS module is switched on: Start ⇒ Settings ⇒ Control Panel ⇒ GSM-Control 4. After start of the operation system, your are asked the PIN of the SIM card. Enter the number given by your provider. When demanded you then enter the APN (Access Point Name) of your provider. As soon as the GSM symbol below in the Systray is active (green) (might take some minutes), doubletip the symbol and select "Connect“ in the window. The GPRS connection is established. The backup battery is on. Backup battery switch – on Insert SIM card* 5. 6.  Remove the battery.  Push the locking of the card holder down.  Swing open the cover of the card holder. 7.  Carefully insert the SIM card. The conical corner should be top left, the contacts of the SIM card should rest on the contacts of the board. GPS-module*  Only slightly insert the SIM card into the holder. If you push it too far into the holder the hinges of the holder might block. You can start GPS with a terminal program of your own choice by piloting the GPS module via COM6 with 9600 baud.  Push the locking upwards, thus locking card holder incl. inserted card. Scan of barcodes Call HWImagerTool to test the scanner function: Start ⇒ Programs ⇒ Utilities ⇒ HWImagerTool HWImagerTool executes in the background and can be identified by the SysTray symbol. Insert Battery Note: Prior to initial operation, the storage battery should be completely charged. To do so, place the device into the docking station. Insert the storage battery with its noses at the rounded part into the relevant recesses inside the battery compartment. Press the battery until it audibly engages. Calmly and angularly hold the skeye.dart in the direction of the barcode to be scanned. A peep indicates that the entry of the barcode has been successful. The gap should amount to about 5-10 cm. An aid to orientation could be the skeye.dart lettering: aim with the red dot. HWImagerTool can be used to scan into any text field (e.g. WordPad). Data synchronisation  Install on your PC the program for data synchronisation of a PC with a mobile device. This program should be appropriate to your operational system.  Microsoft ActiveSync V. 4.5  Windows Mobile Device Center V. 6.1  Windows Mobile Device Center V. 6.1 Switch on Device To switch on the device, use the middle, round key. ⇒ for Windows XP ⇒ for Windows Vista ⇒ for Windows 7 These programs are available for free via www.Microsoft.com/getstarted. With this program you can handle the following tasks:  adding and removing programs on the skeye.dart  synchronisation of files  transfer and copying of files ON key *only available in the skeye.dart FFE version