Transcript
PROFESSIONAL SERIES
USERS MANUAL
SL-52FM
Two Way 3–Channel 915 MHz Extended Range Remote Start Keyless Entry System
This unit is designed for professional installation only.
For Warranty information: Please visit our website at www.silencer.com Magnadyne Corporation
UM_FULL_SL52FM_REV_A
1111 W. Victoria Street, Compton CA 90220
1
(800) 340-3200 PROFESSIONAL SERIES
LCD REMOTE CONTROL TRANSCEIVER: SL-RF92LCD
A. CHANGING THE BATTERY: BATTERY REPLACEMENT: SL-RF92 The Two-Way remote transmitter is powered by one “AAA” Battery. When the power of the battery icon shall be displayed on the LCD screen. When the old battery is replaced, there will be weakens a beep sounds indicate the power is up of the transmitter. The SL-RF91 One-way remote is powered by one CR2032 Battery.
SL-RF91
UM_FULL_SL52FM_REV_A
2 PROFESSIONAL SERIES
B. STANDARD LCD ICON CONFIGURATIONS:
Lock icon will be displayed when the door locked. Valet Mode Remote start and alarm functions shall be temporarily on hold. Remote Transmission You are transmitting the signal to control unit Engine Cranking Your vehicle engine Cranking by remote control
12:00
Time Monitor
0:10 P
Parking Meter Reminder when time is up for parking Melody Mode Remote Control alert user through melody sound Unlock icon will be displayed when the door unlock In – Range Indicator You are within the remote control range. Engine Running Your vehicle’s engine is running
Activate Channel 3 (Trunk Release).
12:00
Alarm Clock You have set morning call alarm Low Battery You have to replace the battery of remote control. Vibration Mode Remote Control vibrates when the system is triggered
UM_FULL_SL52FM_REV_A
3 PROFESSIONAL SERIES
OPERATION: C: REMOTE TRANSMITTER OPERATION: Transmitter Button
System Function
Remark
Lock Doors & Arm System
+
Panic function
Press and Hold for 3 seconds. Press Trunk button to stop panic function
Car Locator
Press when in armed mode
Silent Arming / Disarming
Ignition in “off” position.
Unlock Doors & Disarm System -
+
Two Steps Door Unlock & Disarm System(optional)
Press twice within 3 seconds.
Trunk Release (Channel 3)
Press and Hold for 2 seconds
Activate or Turn Off The Remote Start
Press button once. start safety mode
Switch code for 2nd car operation
For SL-91 remote transmitter only
Press Twice if set to
D: CHIRP INDICATORS:
PARKING LIGHT:
Chirp
Function
Parking light
Function
1 chirp
Lock
1 flash
Lock
2 chirps
Unlock
2 flashes
Unlock
ON
Running on remote start
LED INDICATORS LED
Function
Off
Unlock
Slow Flash
Locked
On (Solid)
Valet Mode
UM_FULL_SL52FM_REV_A
4 PROFESSIONAL SERIES
WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. • Keep the transmitter out of children’s reach. • Do not leave anyone in the vehicle while running on remote control. • Alert servicing personnel that the vehicle can be started automatically. • Do not start the vehicle by remote while it’s in an enclosed area or garage. • Always apply the parking brake and lock the vehicle as you exit the vehicle. • The vehicle windows must be rolled up. • Should the unit malfunction, disconnect the fuse until the problem is corrected. • The use and operations of this system is the sole responsibility of the operator. • Some areas may have local ordinances that prohibit leaving a vehicle running on public streets. • THIS DEVICE CANNOT BE USED ON ANY STANDARD TRANSMISSION VEHICLE. FOR AUTOMATIC TRANSMISSIONS ONLY!
E. ACTIVE LOCK: Press
button on the transmitter.
The horn will chirp once and parking light will flash once indicating that the system is now locked. The vehicle’s doors will lock upon arming if interfaced with the security system. SILENT Lock / Unlock: Press the transmitter and buttons at the same time. This will lock or unlock your security system, No chirp sound will be heard, lock / unlock confirmation will be through the vehicles parking lights only.
F. ACTIVE UNLOCK: 1. Press
button on the transmitter.
2. The horn will chirp twice and the parking lights will flash twice indicating that the security system is now disarmed. The vehicle’s doors will unlock and the dome light will turn on for 30 seconds upon disarming. (Note: Power door locks must be installed with the system.) PATHWAY ILLUMINATION: When receiving an unlock /disarm signal, this feature will turn the parking lights “ON” for 30 seconds and for 10 seconds upon the lock signal. (Programmable) TWO STEPS DOOR UNLOCK (Optional): This feature will independently unlock the driver’s door only when disarming the system. Pushing the button a second time within 3 seconds will unlock the other doors.
G. DEACTIVATING WITHOUT A TRANSMITTER OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting)
The Override function may be used if the remote transmitter is lost or inoperative. 1. Enter the vehicle and turn the ignition switch to the ‘ON’ position. 2. (Alarm will sound.)
3. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally.
UM_FULL_SL52FM_REV_A
5 PROFESSIONAL SERIES
H. VALET MODE: VALET MODE: (System is in Disarm Mode) The valet switch allows you to temporarily bypass all function, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all functions and remote start functions are bypassed, however, the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed either by using your remote transmitter, or by operating the Manual Override sequence. Get into/out valet mode using the ignition key. Enter Valet Mode: a). Under disarm mode, turn the ignition to “ON/OFF/ON” position. b). Press and hold valet switch for 2 seconds until the LED turns ON solid. The LED will remain on as long as the system is in ‘valet mode’. Exit Valet Mode: a). Turn ignition ‘ON/OFF/ON’. b). Push and hold valet switch for 2 seconds, The LED will turn off indicate the system are exiting the valet mode.
I. CAR LOCATOR Under armed mode, press the button to active car locator function. The horn will chirp 6 times. The parking light will flash 12 times, for you to easily locate your car.
J. PANIC FUNCTION: The transmitter can be used as a remote panic switch to manually trigger the horn in case of emergency. 1. Press and hold the
button for 3 second. The alarm will immediately sound.
2. During panic mode, the normal function of this transmitter button will be disabled. The transmitter and buttons can be used to lock and unlock the door (if the option is installed), however once the button is pressed, the vehicle’s starter disable device, (where installed) will be disengaged allowing the vehicle to start. 3. To stop the alarm, press the trunk button on the remote control If the button is not pressed, the alarm will automatically stop after 30 seconds.
K. IGNITION CONTROL DOOR LOCK/UNLOCK. (Programmable Feature) If the vehicles door locks have been interfaced to the security system, the system will automatically lock the vehicle’s doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned “OFF”. (Default setting is “OFF”)
L. TRUNK RELEASE (CHANNEL 3) OUTPUT. Press and hold
button on the transmitter for two seconds to remotely control the trunk release.
M. POWER ON MEMORY: This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected.
N. CLEAR THE FLASH ICON AND MELODY SOUND: The Transmitter will reset the flashing icons the next time the Ignition is cycled to the ON position.
O. STOP THE TRIGGER MELODY SOUND: While triggering the alarm the LCD screen will alert the user through a melody sound and a flashing trigger icon. Press any button on the LCD remote transmitter to stop melody sound only.
UM_FULL_SL52FM_REV_A
6 PROFESSIONAL SERIES
WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of.
1. Keep the transmitter out of children’s reach. 2. Do not leave anyone in the vehicle while running on remote control. 3. Alert servicing personnel that the vehicle can be started automatically. 4. Do not start the vehicle by remote while it’s in an enclosed area or garage. 5. Always apply the parking brake and lock the vehicle as you exit the vehicle. 6. The vehicle windows must be rolled up. 7. Should the unit malfunction, disconnect the fuse until the problem is corrected. 8. The use and operations of this system is the sole responsibility of the operator. 9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets. 10. It is not safe to remote start the vehicle if the vehicle is parked on a steep incline.
REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE: When you want to start your vehicle, 1. Press
button once on the transmitter.
2. The parking light will activate to indicate the remote start received the signal. 3. The engine will start in approximately 5 seconds. 4. Once the engine is running, after couple seconds the parking lights will turn on and the climate controls will activate and adjust the vehicle’s interior temperature to your preset setting. (While the vehicle is running, the “minutes” digit on the LCD screen will flash and the will indicate countdown timer based on the 5, 10, 20 or 30 minute run time set up by your installation center.) 5. The vehicle will run for a programmable 5 to 30 minute cycle before shutting down. (When the unit shuts off the countdown timer will turn off and the transmitter will play a melody.)
NOTE: The Remote Start Unit will not start the vehicle if any one of the following conditions exists: 1. The hood is opened. 2. The brake pedal is pressed. 3. The optional remote start enable toggle is switched to the “OFF” position. (If installed) 4. The gear selector is in any gear other then “PARK” or “NEUTRAL”.
SAFE START (Child safety mode) Factory default is set to press the button once on the transmitter to start the vehicle. You can program this feature to eliminate an accidental remote start: 1. The user presses the transmitter
buttons twice within 3 seconds to start the vehicle. or
NOTE: Contact your installing dealer to activate this feature.
UM_FULL_SL52FM_REV_A
7 PROFESSIONAL SERIES
B. OPERATE THE VEHICLE WHILE RUNNING FROM THE REMOTE START: To operate the vehicle while the engine is running from the remote start, 1. Insert the ignition key and turn it to “ON” (not the start) position. 2. Press the brake pedal. Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
C. TEMPORARY STOP FEATURE: This feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate control on. 1. Before turning off the engine, press the 3 times to confirm enter.
button once on the transmitter and the LED indicator will flash
2. Turn the ignition key to OFF position. (The engine will stay running.) 3. The engine will run until the pre-programmed time elapsed or shutdown input is received.
D. TO TURN OFF THE REMOTE START: When the engine is running (by remote start), if you want to stop it, 1. Press
button once on the remote transmitter under the remote start mode.
2. Move the optional remote start enable toggle switch to OFF position. (If installed) 3. Press the brake pedal The vehicle will shut down and turn off the parking light to indicate the engine has stopped.
E. SHUT-DOWN INPUT FOR REMOTE STARTER: If any of the following conditions exist while the system is operating, the engine will not start or will shut down immediately:
1. The hood is opened. 2. The brake pedal is pressed. 3. The parking (hand) brake is released (For Turbo Timer Mode) 4. Engine is over-revved. {“Tachometer checking type” only} 5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed. 6. Press
button on the remote transmitter under remote start mode.
7. The system trigger. 8. The vehicle refused to start running after {3} unsuccessful attempts.
UM_FULL_SL52FM_REV_A
8 PROFESSIONAL SERIES
ANTENNA: The long range antenna should be located somewhere on the windshield of the vehicle. This antenna also contains the two blue status LED’s as well as the Valet Button / Switch.
TRANSMITTER PROGRAMMING Enter: 1. Turn the Ignition ‘switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds. 2. Push the Valet switch 3 times and hold in on the 3rd push, when a long chirp is heard then release the valet switch. You are now in the Transmitter programming mode. Program: 1. Press any button on transmitter 1 until the siren responds with a confirming chirp; the first transmitter is now programmed. 2. Press any button on the second transmitter until the siren responds with a confirming chirp; the second transmitter is now programmed. 3. Apply the same procedure to program 3rd and 4th .Transmitters. Exit: Turn Ignition to ‘OFF’ position, or leave it for 15 seconds. 3 long chirps and 3 parking light flashes will confirm exit. Note: If more than 4 transmitters programmed, the system will only keep the last four.
UM_FULL_SL52FM_REV_A
9 PROFESSIONAL SERIES
ADVANCED USER’S MODE: 2-WAY LCD REMOTE CONTROL TRANSCEIVER OPERATION: Table 1: Enter : Press & hold “ F “ button until one beep, release F-button and continue press F button within 5 sec. to move forward to feature option you want to program. EXIT: Press & hold “ F “ button for 2 sec. or do nothing wait for 5 sec. automatic exit 2-way LCD (1 beep) => Confirm Exit. F Button
LCD Display
Button
Press and hold the F Button until 1 beeps sound
SENSOR BYPASS and PASS 1 icon On
button Enable to arm Press the alarm and bypass sensor 1.
HIDDEN ALARM and
button Enable to arm Press system and with Hidden Alarm Function.
Press F Button 2nd time (HHU 1 beep) within 5 seconds Press F Button 3rd time (HHU 1 beep) within 5 seconds Press F Button 4th time (HHU 1 beep) within 5 seconds
icon On ANTI- HIJACK and
Under ignition in “on” position Press button Enable to activate anti carjacking functions.
icon On
Press output
CH 4 flashing
button Enable CH#4
Note: Press and release F Button 2-way LCD Backlight turns on for 5 seconds
Table 2: Enter : Press & hold “ F “ button until 2 beeps heard, release F-button. Continue press F button within 5 sec. to move forward to feature option you want to program. EXIT: Press & hold “ F “ button for 2 sec. or do nothing wait for 5 sec. automatic exit 2-way LCD (1 beep) => Confirm Exit. F Button
LCD display
Button
Press and hold the F Button until 2 beeps sounded
MENU flashing
button to enter 2-way Press HHU menu mode
Press F Button 2nd time (HHU 1 beep) within 5 seconds
STATUS CHECK
button Enable to check the Press vehicle’s status.
Press F Button 3rd times (HHU 1 beep) within 5 seconds
ALARM CHECK
button Enable to check Press vehicle’s trigger status.
Press F Button 4th times (HHU 1 beep) within 5 seconds
VOLTS CHECK
button Enable to check Press vehicle’s Voltage.
Press F Button 5th time (HHU 1 beep) within 5 seconds
TEMP CHECK
button Enable to check Press temp. status
UM_FULL_SL52FM_REV_A
10 PROFESSIONAL SERIES
Table 3: Return 2-way HHU to default setting Enter : Press & hold “ F “ button until 4 beeps heard, release F-button. EXIT: Press & release “ F “ button or do nothing wait for 5 sec. automatic exit 2-way LCD (1 beep) => Confirm Exit. F Button
LCD display
Button
Press and hold the F Button until 4 beeps sounded
RESET flashing
button for 2 seconds to back to Press & hold default setting and 1 chip for confirm
2-way LCD HHU PROGRAMMING (Select and Adjusting Table-2-Menu options): Enter: Press and hold F button until 2 beeps heard then release the F button. The Display will show MENU flashing, press
button to enter HHU menu mode.
(LCD display show Hours of current time set up, set up hour(s) first.) Press
button to increase value, or Enable the selected feature.
Press
button to decrease value, or Disable the selected feature .
Press
button to confirm its selection, move to the next option.
EXIT: Press & hold “ F “ button or do nothing wait for 15 sec. automatic exit 2-way LCD (1 beep) => Confirm Exit. Menu Option 1
2
3
LCD display
Current time set up
Functions Default is 12:00
Adjust clock hours from 0 to 12
12 : 00 12 is flashing
Press Press
button = (+) or Press button = (-) button confirm its selection, move to next option.
Adjust clock minutes from 0 to 59
12: 00 00 is flashing
Press Press
button = (+) or Press button = (-) button confirm its selection, move to next option.
Default is OFF
Alarm Clock set up Adjust Alarm Clock hours from 0 to 12
12 :00 12 is flashing
Press Press
button = (+) or Press button = (-) button confirm its selection, move to next option.
Adjust Alarm Clock minutes from 0 to 59
12: 00 00 is flashing
Press Press
button = (+) or Press button = (-) button confirm its selection, move to next option.
Select Alarm Clock Enable or Disable
ON +
Press Press
button = Enable or Press button = Disable button confirm its selection, move to next option.
Parking Meter countdown
PARK METER
Default is OFF
Adjust Parking Meter countdown hours from 0 to 2
0 :00 0 is flashing
Press Press Press
button = (+) or button = (-) button confirm its selection, move to next option.
Press Press
button = (+) or Press button = (-) button confirm its selection, move to next option.
Adjust Parking Meter countdown minutes from 0 to 59.
UM_FULL_SL52FM_REV_A
or OFF
0 : 30 30 is flashing
11 PROFESSIONAL SERIES
Select Parking meter countdown Enable or Disable 4
P-- ON +
or
P -- OFF
Power Save
Press button = Enable or Press button = Disable Press button confirm its selection, move to next option. There is a beep sound at 5 min. before Parking countdown reach 0. Default is OFF Press
Select Power Save Enable or Disable
+
or
button = Enable or Press
button = Disable
When power save enable, the LCD remote transceiver uses “0” current to save the battery power. LCD show “Save” on text area Exit: Press any button of LCD remote to exit the “Power Save Mode”. Press button confirm its selection, move to next option.
5
2-way HHU Response mode Select 2-way HHU confirmation by Melody or Vibration
VIB +
or VIB
Default is Buzzer
+
Press
button = Melody or
Press
button = Vibration
Press
button confirm its selected, move to next option.
or
BZ+VIB + 6
Second Car Security Option
or +
CAR SELECT CAR 1 or CAR 2
7
Illumination Menu 5 SEC. or OFF
9
Key Lock
CAR ICON Illumination*
(Time adjust for Daily Start mode)
,
- CAR 2 operation
Basic operation with backlight Illumination 3 SEC. or 5 SEC.;
OFF – basic operation without backlight illumination.
KEY LOCK
Default is OFF
Key lock enable or disable
Press
LCD icon appear or not
10
- CAR 1 operation. Default is
3 SEC. or
8
Default is CAR 1
icon flashing
button = Enable or Press
button = Disable
Default is OFF Press
button = Enable or Press
button = Disable
Default is OFF
1 -12
12 : 00 12 is flashing
, - Program Daily start hour Press button = (+) hours increase or Press button = (-) hours decrease
0 - 59
12 : 00 00 is flashing
, - Program Daily start minute Press button = (+) minutes increase or Press button = (-)minutes decrease
* Car LCD icon is programmable show car icon on LCD display always or appear if needed as below. (system trigger / valet mode / zone ajar/ anti car-jacking mode car LCD will show on LCD display).
UM_FULL_SL52FM_REV_A
12 PROFESSIONAL SERIES
SILENCER LIMITED LIFETIME WARRANTY Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original purchaser, repair, replace or refund the retail sales price of said product or any part thereof, at the option of the Magnadyne Corporation or its authorized agents, if said product or part is found defective in materials or workmanship, when properly connected and operating on the correct power requirements designated for the specific product. This warranty and Magnadyne Corporation or its authorized agents obligations, hereunder do not apply where the product was: damaged while in the possession of the consumer, subjected to unreasonable or unintended use, not reasonably maintained, utilized in commercial or industrial operation, or serviced by anyone other than Magnadyne Corporation or its authorized agent, or where the warning seal on the product is broken or the power plugs or wires are detached from the unit. Magnadyne Corporation or any of its authorized agents do not assume any labor costs for the removal and reinstallation of any product found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized agents. Such costs are the sole responsibility of the purchaser. This warranty does not cover the cabinet, appearance items, normal wear and tear or accessories used in connection with the product resulting from improper installation, alteration, accident, misuse, abuse or acts of nature. This Limited Life Time Warranty applies only to the receiver section of the security system. Neither the siren, transmitters, wire harness or any accessory item added to or used with a Remote Mobile security system are covered by this Limited Life Time Warranty. Sirens, transmitters, wire harness or any accessory item are covered by our standard 12 month limited warranty. Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential or incidental damages or claims that may arise due to failure of product to operate properly except those accorded by law. Magnadyne’s or its authorized agents liability to the repair, replacement of the product as stated above if all conditions of the warranty are met. No expressed warranty or implied warranty is given except those set forth herein. Magnadyne does not warrant or guarantee against break in damage or the theft of the vehicle in part or whole, or against the loss or damage to the contents of any vehicle in which a security system is installed. Magnadyne security systems are only a deterrent against possible theft. This warranty extends only to the original purchaser of the product and for the vehicle in which it was originally installed. This warranty is not transferable or assignable to any person or vehicle. Defective merchandise should be returned to the original point of purchase or secondly to Magnadyne Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization must be obtained before sending, or merchandise may be refused.
LIMITED LIFETIME WARRANTY REGISTRATION CARD Complete and mail now. Please print clearly.
FIRST NAMEI
LAST NAME
NITIAL
ADDRESS
CITY
STATE
ZIP
DEALER DATE OF PURCHASE
MODEL #
MAKE OF CAR
YEARL
ICENSE#
It is the purchaser’s responsibility to register this product for any future warranty service. Warning: Some batteries may contain Perchlorate What is Perchlorate? Perchlorate is both a naturally occurring and manmade contaminant increasingly found in groundwater, surface water and soil. Most perchlorate manufactured in the U.S. is used as an ingredient in solid fuel for rockets and missiles. In addition, perchlorate-based chemicals are also used in the construction of highway safety flares, fireworks, pyrotechnics, explosives, common batteries, and automobile restraint systems. Perchlorate contamination has been reported in at least 20 states. Perchlorate greatly impacts human health by interfering with iodide uptake into the thyroid gland. In adults, the thyroid gland helps regulate the metabolism by releasing hormones, while in children; the thyroid helps in proper development. Perchlorate is becoming a serious threat to human health and water resources. “Perchlorate Material – Special handling may apply.” For more information, go to http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
Magnadyne Corporation
1111 W. Victoria Street
Compton CA 90220 (800) 340-3200
Please visit our website at www.silencer.com Made in Taiwan. All Rights Reserved UM_FULL_SL52FM_REV_A
13 PROFESSIONAL SERIES
