Transcript
http://www.xiaoyu163.com
SLV-EX50/EX80S/EX90S RMT-V312/V312A QQ 376315150 892498299 SERVICE MANUAL
Argentina Model
SLV-EX50AR/EX80SAR/ EX90SAR
Brazil Model SLV-EX50BR/EX80SBR/ EX90SBR
1 4 7
2
3
5
6
8
9
0
TEL
TEL
g
SLV-EX90S
S MECHANISM
QQ 376315150 892498299
* The abbreviations of EX50/EX80S and EX90S contained in this service manual are indicated when these models are common to all their corresponding models as given below. Abbreviated model name
EX50
EX80S
EX90S
All model names SLV-
EX50AR EX50BR
EX80SAR EX80SBR
EX90SAR EX90SBR
www
xiaoy u163. com
VIDEO CASSETTE RECORDER
.
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL 13942296513
QQ
QQ
Refer to the SERVICE MANUAL of VHS MECHANICAL ADJUSTMENTS VI for MECHANICAL ADJUSTMENTS. (9-921-647-11)
13942296513
13942296513
VIDEO
http://www.xiaoyu163.com
QQ 376315150 892498299 SPECIFICATIONS
Supplied accessories Remote commander (1) Size AA(R6) batteries (2) 75-ohm coaxial cable with F-type connectors (1) Audio/video cable (3-phono to 3-phono) (SLV-EX80SBR/EX90SBR) (1) Design and specifications are subject to change without notice.
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.
4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.
2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.
5. Check the B+ voltage to see it is at the values specified.
3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
www
xiaoy u163. com SAFETY-RELATED COMPONENT WARNING!!
.
COMPONENTS IDENTIFIED BY MARK OR DOTTED LINE WITH MARK ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
–2–
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 376315150 892498299
TEL 13942296513
QQ
QQ
Tuner Section Channel coverage VHF 2 to 13 UHF 14 to 69 Timer section CATV A-8 to A-1, A to W, W+1 to W+84 Clock Antenna Quartz locked 75-ohm antenna terminal for VHF/UHF Timer indication 12-hour cycle Inputs and Outputs Timer setting SLV-EX80S/EX90S: 8 programs per month (max.) LINE-1 IN and LINE-2 IN VIDEO IN, phono jack (1 each) Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative
General Power requirements 110-240 V AC, 50/60 Hz (SLV-EX50BR/EX80SBR/EX90SBR) 220 V AC, 50 Hz (SLV-EX50AR/EX80SAR/EX90SAR) Power consumption 14 W (SLV-EX80S/EX90S) 12 W (SLV-EX50) Operating temperature 5°C to 40°C Storage temperature –20°C to 60°C Dimensions Approx. 430 x 97 x 292 mm (w/h/d) including projecting parts and controls Mass Approx. 4.1 kg Power back-up Built-in self-charging capacitor Back-up duration: up to 8 hours at a time
13942296513
13942296513
AUDIO IN, phono jack (2 each) Input level: 327 mVrms Input impedance: more than 47 kilohms LINE OUT VIDEO OUT, phono jack (1) Output signal: 1 Vp-p, 75 ohms, unbalanced, sync negative AUDIO OUT, phono jack (2) Standard output: 327 mVrms Load impedance: 47 kilohms Output impedance: less than 10 kilohms SLV-EX50: LINE-1 IN VIDEO IN, phono jack (1) Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative AUDIO IN, phono jack (1) Input level: 327 mVrms Input impedance: more than 47 kilohms LINE-OUT VIDEO OUT, phono jack (1) Output signal: 1 Vp-p, 75 ohms, unbalanced, sync negative AUDIO OUT, phono jack (1) Standard output: 327 mVrms Load impedance: 47 kilohms Output impedance: less than 10 kilohms
TEL
TEL
System Format VHS N-PAL, NTSC standard (SLV-EX50AR/EX80SAR/EX90SAR) VHS M-PAL, NTSC standard (SLV-EX50BR/EX80SBR/EX90SAR) Video recording system Rotary head helical scanning FM system Video heads Double azimuth four heads (SLV-EX80S/EX90S) Double azimuth two heads (SLV-EX50) Video signal NTSC color, EIA standards Tape speed SP: 33.35 mm/s (1 3/8 inches/s) EP: 11.11 mm/s ( 7/16 inches/s) LP: 16.67 mm/s ( 11/16 inches/s), playback only Maximum recording/playback time 8 hrs. in EP mode (with T-160 tape) Fast-forward and rewind time Approx. 3 min. (with T-20 tape)
http://www.xiaoyu163.com
QQ 376315150 892498299 TABLE OF CONTENTS
Section
Title
Page
Section
Feature Difference ................................................................... 3 SERVICE NOTE ....................................................................... 5
1.
GENERAL
5-1.
System Control-Video Block Interface (MA-402 BOARD IC101) .............................................. System Control-Servo Peripheral Circuit Interface (MA-402 BOARD IC101) .............................................. System Control-Mechanism Block Interface (MA-402 BOARD IC101) .............................................. System Control-Audio Block Interface (MA-402 BOARD IC101) .............................................. Servo/System Control, OSD Microprocessor Pin Function (MA-402 BOARD IC101) ............................................... NICAM Processor Pin Function (NK-11 BOARD IC1) .....................................................
5-3. 5-4. 5-5.
2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7.
Case Front Panel Block Assembly ................................ DM-98, DI-81 Board and FJ-31 Board .......................... Rear Panel ..................................................................... MA-402 Board ................................................................ Mechanism Deck ........................................................... Internal Views ................................................................. Circuit Boards Location .................................................
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7.
Overall Block Diagram ................................................... Video Block Diagram ..................................................... Servo/System Control Block Diagram ........................... Audio Block Diagram ..................................................... Tuner Block Diagram ..................................................... Mode Control Block Diagram ........................................ Power Block Diagram .....................................................
4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. 4-2.
Frame Schematic Diagram ............................................ Printed Wiring Boards and Schematic Diagrams ......... • MA-402 Printed Wiring Board .................................. • MA-402 (Video, Audio) Schematic Diagram ............ • MA-402 (System Control) Schematic Diagram ....... • MA-402 (Servo Control) Schematic Diagram .......... • MA-402 (Hi-Fi Audio) Schematic Diagram ............... • MA-402 (Tuner) Schematic Diagram ........................ • MA-402 (I/O) Schematic Diagram ............................ • MA-402 (Mode Control) Schematic Diagram ........... • MA-402 (Power Supply) Schematic Diagram ......... • FJ-31 Printed Wiring Boards and Schematic Diagrams ................................................ • DM-98 Printed Wiring Boards and Schematic Diagrams ................................................ • DI-81 Printed Wiring Board and Schematic Diagrams ................................................
ERROR CODES
7.
ADJUSTMENTS
QQ 376315150 892498299
TEL 13942296513
4-3 4-5 4-5 4-9 4-13 4-17 4-19 4-21 4-23 4-25 4-27 4-31
5-5E
7-1 7-1 7-1 7-1 7-1 7-1 7-1 7-1 7-2 7-2 7-2 7-2 7-2 7-3 7-3 7-3 7-3 7-4 7-4 7-4 7-4 7-4 7-4 7-5 7-5 7-5 7-5 7-6E
4-31
8.
4-33
REPAIR PARTS LIST
8-1. Exploded Views .............................................................. 8-1-1. Front Panel and Upper Case Section ...................... 8-1-2. Chassis Section ........................................................ 8-1-3. Mechanism Deck Section-1 ...................................... 8-1-4. Mechanism Deck Section-2 ...................................... 8-1-5. Mechanism Deck Section-3 ...................................... 8-2. Electrical Parts List ........................................................
.
5-4
..................................................... 6-1E
7-1. Mechanical Adjustments ............................................... 7-2. Electrical Adjustments ................................................... 2-1. Pre-Adjustment Preparations ........................................ 2-1-1. Instruments to be Used ............................................ 2-1-2. Connection ................................................................ 2-1-3. Set-up of Adjustment ................................................ 2-1-4. Alingment Tapes ....................................................... 2-1-5. Specified I/O Level and Impedance ......................... 2-1-6. Adjusting Sequence .................................................. 2-2. Power Supply Adjustment .............................................. 2-2-1. Power Supply Check ................................................. 2-3. Servo System Adjustment ............................................. 2-3-1. RF Switching Position Adjustment ........................... 2-4. Audio System Adjustments ............................................ 2-4-1. Hi-Fi Audio System Adjustment ............................... 1. AF Switching Position Adjustment ........................... 2. Frequency Response Check .................................... 3. Overall Level Characteristic and Distortion Factor Check ............................................ 4. Overall S/N Check .................................................... 2-4-2. Normal Audio System Adjustment ........................... 1. ACE Head Adjustment .............................................. 2. E-E Output Level Check ........................................... 3. Frequency Responce Check .................................... 4. Overall Level Characteristic and Distortion Factor Check ............................................................. 5. Overall S/N Check .................................................... 2-5. Tuner System Adjustment .............................................. 2-5-1. Separation Adjustment ............................................. 2-6. Parts Arrangement Diagram for Adjustments ...............
3-1 3-3 3-5 3-7 3-9 3-11 3-13
5-3
xiaoy u163. com –3–
http://www.xiaoyu163.com
8-1 8-1 8-3 8-5 8-6 8-7 8-8
376315150 892498299
376315150 892498299
BLOCK DIAGRAMS
6.
5-2
QQ
QQ
3.
2-1 2-1 2-2 2-2 2-3 2-4 2-5E
5-1
13942296513
13942296513
DISASSEMBLY
5-1
TEL
TEL
INTERFACE, IC PIN FUNCTION DESCRIPTION
5-6.
2.
www
1-1 1-5 1-9 1-10 1-13
Page
5.
5-2.
Getting Started ............................................................... Basic Operations ........................................................... Search Operations ........................................................ Additional Operations .................................................... Additional Information ....................................................
Title
http://www.xiaoyu163.com
QQ 376315150 892498299 SERVICE NOTE
1. DISASSEMBLY
• This set can be disassembled in the order shown below. Note: Pages in Pages in
indicated pages in the SERVICE MANUAL. indicated pages in the VHS MECHANICAL ADJUSTMENT MANUAL VI.
Set
Upper case (Page 2-1)
Mechanism Deck (Page 2-3)
Drum Ass’y (Page 13)
Retainer Plate (Page 22)
Rubber Belt (Page 15)
Rubber Belt (Page 15)
MA-402 Board (Page 2-2)
FL Slider Block Ass’y (Page 22)
Capstan Motor (Page 15)
Pully Gear Ass’y (Page 29)
Rotary Switch (Page 2-3)
Cam Gear (Page 23)
Cam Motor Retainer (Page 31)
Reel Direct Ass’y (Page 30)
Rubber Belt (Page 15)
Cam Motor (Page 31)
TEL 13942296513
QQ 376315150 892498299 Tuner Unit
Slider (Page 26)
Loading Gear (T, S) (Page 28)
www
.
xiaoy u163. com –4–
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
FL Complete Ass’y (Page 13)
Rear Panel (Page 2-2)
QQ
QQ
Ground Shaft Ass’y (Page 13)
13942296513
13942296513
Pinch Press Block Ass’y (Page 14)
TEL
TEL
Front Panel Section (Page 2-1)
http://www.xiaoyu163.com
SLV-EX50/EX80S/EX90S
QQ 376315150 892498299
This section is a translated version of Instruction Manual SLV-EX50AR/ EX80SAR/EX90SAR model. Part number: 3-066-370-11
SECTION 1 GENERAL
Step 2
Step 3
Setting up the remote commander
Hookups
Inserting the batteries
Selecting the best hookup option Getting Started
Insert two size AA (R6) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.
There are many ways in which your VCR can be hooked up. To hook up your VCR so that it works best for you, first scan through the table below. Then use the accompanying diagrams and procedures on the following pages to set up your VCR. If your TV has audio/video inputs, refer to pages 7 and 8 for audio/video (A/V) hookup. Then follow one of the hookups below.
Using the remote commander Remote sensor
Use
Refer to
Antenna only, no cable TV
Hookup 1
Page 9
Cable box with many scrambled channels
Hookup 2
Page 10
No cable box, or cable box with only a few scrambled channels
Hookup 3
Page 11
Cable box with only a few scrambled channels, using an A/B switch
Hookup 4
Page 12
After you’ve completed the connections, follow the instructions for setup.
13942296513
To operate
Set TV/VIDEO to
the VCR
VIDEO and point at the remote sensor on the VCR
a Sony TV
TV and point at the remote sensor on the TV
Before you get started • Turn off the power to all equipment. • Do not connect the AC power cords until all of the connections are completed. • Be sure you make connections firmly. Loose connections may cause picture distortion. • If your TV doesn’t match any of the examples provided, see your nearest Sony dealer or qualified technician.
Notes • With normal use, the batteries should last about three to six months. • If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage. • Do not use a new battery with an old one. • Do not use different types of batteries. • Some buttons may not work with certain Sony TVs.
6
Getting Started
Step 3: Hookups (continued)
Audio/video (A/V) hookup
Pages 7 and 8
If your TV has audio/video (A/V) input jacks, you will get a better picture and sound if you hook up your VCR using these connections. If your TV doesn’t have A/V inputs, see the following pages for antenna or cable hookups. If you’re not planning to use your VCR to record programs, you’re finished setting up the VCR after you’ve made the connections shown on pages 7 and 8. If you want to record off-air or off your cable TV system, complete these connections first, and then go to the following pages for antenna or cable hookups.
For SLV-EX50 AR A Use this hookup if your TV has stereo jacks VCR TV AUDIO
LINE OUT
AUDIO
Audio/video cable (not supplied)
B Use this hookup if your TV doesn’t have stereo jacks VCR
A Use this hookup if your TV has stereo jacks
TV Stereo receiver
AUDIO
VIDEO LINE OUT
TV
AUDIO
IN
LINE OUT
VIDEO
AUDIO OUT
AUDIO
Audio/video cable (not supplied) Audio/video cable (not supplied)
Audio cable (not supplied)
B Use this hookup if your TV doesn’t have stereo jacks Stereo receiver
VCR TV
AUX IN
R AUDIO L VIDEO LINE OUT
IN VIDEO AUDIO
www
Video cable (not supplied)
xiaoy u163. com Audio cable (not supplied)
Note • To play a tape in stereo, you must use the A/V connection.
.
IN VIDEO
AUX IN
R AUDIO L VIDEO
IN VIDEO
For SLV-EX90S AR and EX80S AR For a true “home theater” experience, you should connect the audio outputs of your VCR or TV to your stereo system.
VCR
VIDEO
continued
Getting Started
7
8
Getting Started
– 1-1 –
http://www.xiaoyu163.com
376315150 892498299
QQ 376315150 892498299
5
Getting Started
376315150 892498299
Getting Started
QQ
QQ
TEL 13942296513
13942296513
After you’ve completed the setup, you’re ready to use your VCR. Procedures differ depending on the hookup you used. For an overview, refer to “Quick reference to using the VCR” on the back cover.
TV/VIDEO
TEL
TEL
You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the g symbol near the remote sensor, this remote commander will not operate the TV.
If you have
http://www.xiaoyu163.com
QQ 376315150 892498299 Step 3: Hookups (continued)
Page 9
Hookup 1
Page 10
Hookup 2
Antenna hookup Make the following connections if you’re using an antenna (if you don’t have cable TV).
or VCR
Rear of TV VHF/UHF A Match the type of connector on your TV: A, B, or C. VHF
Hookup 4 Connecting a cable box with many scrambled channels
Getting Started
A Use this hookup if you’re using: • VHF/UHF antenna (you get channels 2–13 and channels 14 and higher) • UHF-only antenna (you get channels 14 and higher) • Separate VHF and UHF antennas
Recommended use Use this hookup if your cable system scrambles all or most channels. What you can do with this hookup • Record any channel by selecting the channel on the cable box What you can’t do • Record with the cable box turned off • Record one channel while watching another channel
B VHF/UHF
or
OUT
Rear of TV
Cable box
Wall
UHF
IN
IN OUT
VHF C
or
B Use this hookup if you’re using a VHF-only antenna (you get channels 2–13 only)
or
VHF
VHF
VCR
B VHF/UHF IN
or
OUT
UHF VHF
VHF/UHF
UHF
IN
Match the type of connector on your TV: A, B, or C.
13942296513
13942296513
A
C
VCR
Rear of TV VHF/UHF
or
OUT
For connector types B and C, no UHF connection is required.
C UHF
9
10
Getting Started
Step 3: Hookups (continued) Page 11
Hookup 3
Recommended use Use this hookup if you do not have a cable box. Also use this hookup if your cable system scrambles only a few channels. What you can do with this hookup • Record any unscrambled channel by selecting the channel on the VCR What you can’t do • Record scrambled channels that require a cable box VCR Wall
OUT
or
or
Connect this cable directly to your TV if you don’t have a cable box.
Connecting a cable box with only a few scrambled channels, using an A/B switch Recommended use By using an A/B switch (not supplied), this hookup allows you to record both scrambled and unscrambled channels conveniently. What you can do with this hookup • Record any unscrambled channel by selecting the channel directly on the VCR (the A/B switch is set to A) • Record any scrambled channel by selecting the channel on the cable box (the A/B switch is set to B)
Rear of TV VHF/UHF IN
Page 12
Hookup 4
You have no cable box, or cable box with only a few scrambled channels Getting Started
376315150 892498299
QQ 376315150 892498299
VHF/UHF A Match the type of connector on your TV: A, B, or C. VHF B For connector types B and C, no UHF connection UHF is required.
What you can’t do • Record one scrambled channel while watching another channel (the A/B switch is set to B) Wall
Cable box
Splitter
Rear of TV
IN OUT
or C
Cable box IN
A/B switch A
UHF
OUT
B or
VCR
VHF/UHF A Match the type of connector on your TV: A, B, VHF or C. B For connector types B and C, no UHF UHF connection is VHF required. C
VHF/UHF IN
continued
www
.
OUT
xiaoy u163. com Getting Started
11
12
Getting Started
– 1-2 –
http://www.xiaoyu163.com
376315150 892498299
TEL 13942296513
continued
QQ
QQ
If you cannot connect your antenna cable to the VCR directly If your antenna cable is a flat cable (300-ohm twin lead cable), attach an external antenna connector (not supplied) so you can connect the cable to the VHF/UHF IN connector. If you have separate cables for VHF and UHF antennas, you should use a U/V band mixer (not supplied). For details, see page 60.
Getting Started
TEL
TEL
UHF
VHF/UHF A Match the type of connector on your TV: A, B, or C. VHF For connector B types B and C, no UHF connection UHF is required.
http://www.xiaoyu163.com
QQ 376315150 892498299 Step 4
Step 4: Setting the RF unit (continued)
Setting the RF unit
5
?/1
Turn on your TV and set it to the channel you selected in step 1 (channel 3 or 4).
TV/VIDEO
If you made A/V connections (pages 7 and 8), you can skip this step.
1
2
3
4
5
6
7
8
9
The channel you selected in step 4 appears on the TV screen. If the channels change when you press CH +/–, you have made the correct setting.
Getting Started
When connecting the VCR to the TV using only the antenna cable, you must set the RF UNIT switch on the rear of the VCR so that the TV can receive the correct signal from the VCR.
Whenever you use the VCR, set the TV to the channel selected in step 1.
0
CH +/–
RF UNIT switch
2
• ]/1
Press ?/1 to turn on the VCR.
• TV/ VIDEO
Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.
3 4
CH3 CH4
• CH
Set the RF UNIT switch on the rear of the VCR to CH3 or CH4, whichever channel is not used in your area. If both are used, set the switch to either channel.
13942296513
13942296513
RF UNIT
TEL
TEL
1
Press CH +/– to display a channel number in the display window. Select an active channel number in your area.
continued
Getting Started
13
14
Getting Started
Selecting a language
Presetting channels
You can change the on-screen display language from Spanish to English.
MENU
Before you start... • Turn on the VCR and the TV. • Set the TV to the VCR channel (channel 3 or 4). If your TV is connected to the VCR using A/V connections, set the TV to video input. • Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.
OK M/m
First, we recommend that you preset the receivable channels in your area using the One Touch Tuning function or SINTONIA AUTOMATICA in the AJUSTE DE SINTONIA menu. Then, if some channels cannot be preset automatically, set them manually. If there are any unwanted channels among the preset ones, you can disable the channels.
ONE TOUCH TUNING
ONE TOUCH TUNING
1
MENU
CHANNEL +/–
Presetting all receivable channels using the One Touch Tuning function
Press MENU, then press M/m to move the cursor (B) to SELECCION DEL IDIOMA and press OK.
Press and hold ONE TOUCH TUNING on the VCR for more than three seconds. The VCR starts presetting the channel.
SELECCION DEL IDIOMA • ESPAÑOL ENGLISH
SP APC
PLAY
SELECCIONAR FIN
OK
2
: [V v] : [ OK ]
The WAIT indicator goes off when all receivable channels are preset. To check if the channels are preset correctly Set the TV to the video channel and press CHANNEL +/– on the VCR. If the TV screen changes to a different program each time you press CHANNEL +/–, the channels are preset correctly.
Press M/m to select the desired language, then press OK. PLAY OK
www
Tip • To stop the One Touch Tuning function, press ONE TOUCH TUNING or x STOP on the VCR during the setting.
xiaoy u163. com
Note • The menu disappears automatically if you don’t proceed for more than a few minutes.
.
Getting Started
15
16
Getting Started
– 1-3 –
http://www.xiaoyu163.com
376315150 892498299
Step 6
Getting Started
376315150 892498299
Step 5
QQ
QQ
QQ 376315150 892498299
TEL 13942296513
http://www.xiaoyu163.com
QQ 376315150 892498299 Step 6: Presetting channels (continued)
Presetting all receivable channels automatically
2
If you have preset the channels using the One Touch Tuning function, skip this procedure.
Press M/m to select ANTENA/CABLE. PLAY OK
1
2
3
4
5
6
7
8
Getting Started
Before you start… • Turn on the VCR and the TV. • Set the TV to the VCR channel (channel 3 or 4). If your TV is connected to the VCR using A/V connections, set the TV to video input. • Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.
9
3
• To preset cable TV channels: Press , to set ANTENA/CABLE to CABLE.
PLAY OK
0
AJUSTE DE SINTONIA
SELECCIONAR AJUSTAR
• To preset VHF and UHF channels: Press , to set ANTENA/CABLE to ANT.
PLAY OK
CAN 1
ANT • CABLE ANTENA / CABLE SINTONIA AUTOMATICA – •+ SINT. MANUAL • SI NO AFT SINTONIA FINA.
: [V v] : [B b]
AJUSTE DE SINTONIA
CAN 1
ANTENA / CABLE • ANT CABLE SINTONIA AUTOMATICA – •+ SINT. MANUAL AFT • SI NO SINTONIA FINA.
MENU SELECCIONAR AJUSTAR
Press M/m to move the cursor (B) to SINTONIA AUTOMATICA, then press OK.
PLAY OK
MENU
Press MENU, then press M/m to move the cursor (B) to AJUSTE DE SINTONIA and press OK.
AJUSTE DE SINTONIA
All receivable channels are preset in numerical sequence. When no more receivable channels can be found, presetting stops and the picture from the lowest numbered channel is displayed on the TV screen.
CAN 1
ANT • CABLE ANTENA / CABLE SINTONIA AUTOMATICA – •+ SINT. MANUAL • SI NO AFT SINTONIA FINA.
CAN 1
ANT • CABLE ANTENA / CABLE SINTONIA AUTOMATICA – •+ SINT. MANUAL • SI NO AFT SINTONIA FINA.
13942296513
13942296513
1
AJUSTE DE SINTONIA
POR FAVOR ESPERE
PLAY
SELECCIONAR AJUSTAR
OK
: [V v] : [B b]
Note • The menu disappears automatically if you don’t proceed for more than a few minutes.
continued
Getting Started
17
18
Getting Started
Before you start… • Turn on the VCR and the TV. • Set the TV to the VCR channel (channel 3 or 4). If your TV is connected to the VCR using A/V connections, set the TV to video input. • Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.
2 1
2
3
4
5
6
7
8
9
0
Number buttons, ENTER
1
2
3
4
5
6
7
8
9
0
• To preset a channel: 1 Press the number buttons to enter the channel number, then press ENTER. 2 Press , to set SINT. MANUAL to +.
Channel to be preset AJUSTE DE SINTONIA
SELECCIONAR AJUSTAR
• CH
CH +/–
• To disable a channel: 1 Press CH +/– to select the channel number. 2 Press , to set SINT. MANUAL to –.
3 PLAY
: [V v] : [B b]
Channel to be disabled AJUSTE DE SINTONIA
: [V v] : [B b]
Repeat step 2 to preset or disable channels as required, then press OK.
OK
OK M/m/,
1
MENU
Press MENU, then press M/m to move the cursor (B) to AJUSTE DE SINTONIA and press OK.
AJUSTE DE SINTONIA
Note • The menu disappears automatically if you don’t proceed for more than a few minutes.
CAN 1
ANT • CABLE ANTENA / CABLE SINTONIA AUTOMATICA – •+ SINT. MANUAL • SI NO AFT SINTONIA FINA.
PLAY
SELECCIONAR AJUSTAR
OK
www
: [V v] : [B b]
xiaoy u163. com continued
.
Getting Started
19
20
CAN 5
ANT • CABLE ANTENA / CABLE SINTONIA AUTOMATICA + •– SINT. MANUAL • SI NO AFT SINTONIA FINA.
SELECCIONAR AJUSTAR
MENU
CAN 4
ANT • CABLE ANTENA / CABLE SINTONIA AUTOMATICA – •+ SINT. MANUAL • SI NO AFT SINTONIA FINA.
Getting Started
– 1-4 –
http://www.xiaoyu163.com
376315150 892498299
Step 6: Presetting channels (continued)
Presetting/disabling channels manually
Getting Started
376315150 892498299
QQ 376315150 892498299
QQ
QQ
TEL 13942296513
TEL
TEL
4
OK M/m/,
: [V v] : [B b]
http://www.xiaoyu163.com
QQ 376315150 892498299 Step 6: Presetting channels (continued)
If the picture is not clear
Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels clearly. If, however, the picture of a channel is not clear, you can also use the manual tuning function.
2 2
3
4
5
6
7
8
9
Getting Started
1
Number buttons, ENTER
0
1
2
3
4
5
6
7
8
9
Press the number buttons to select the channel you want to fine-tune, then press ENTER.
Selected channel
ANT • CABLE ANTENA / CABLE SINTONIA AUTOMATICA – •+ SINT. MANUAL • SI NO AFT SINTONIA FINA.
0
SELECCIONAR AJUSTAR
3 PLAY OK
Press M/m to move the cursor (B) to SINTONIA FINA. The fine tuning meter appears.
4 PLAY
Press , to adjust to a clearer picture, then press OK. Note that the AFT setting switches to NO.
OK M/m/,
MENU
Press MENU, then press M/m to move the cursor (B) to AJUSTE DE SINTONIA and press OK.
SELECCIONAR AJUSTAR
ANT • CABLE ANTENA / CABLE SINTONIA AUTOMATICA – •+ SINT. MANUAL AFT SI • NO SINTONIA FINA.
: [B b]
Tip • To select the channel in step 2 above, you can also use the CH +/– buttons. In this case, you don’t need to press ENTER.
ANT • CABLE ANTENA / CABLE SINTONIA AUTOMATICA – •+ SINT. MANUAL • SI NO AFT SINTONIA FINA.
Notes • The menu disappears automatically if you don’t proceed for more than a few minutes. • When adjusting FINE TUNING, the menu may become difficult to read due to interference from the picture being received.
PLAY OK
CAN 1 4
AJUSTE DE SINTONIA
AJUSTAR
CAN 1
AJUSTE DE SINTONIA
: [B b]
: [V v] : [B b]
continued
Getting Started
21
22
Getting Started
Setting the clock
3 PLAY
You must set the time and date on the VCR to be able to use the timer recording features properly. Before you start... • Turn on the VCR and the TV. • Set the TV to the VCR channel (channel 3 or 4). If your TV is connected to the VCR using A/V connections, set the TV to video input. • Press TV/VIDEO to display the VIDEO indicator in the VCR’s display window.
Press , to select the month and press M/m to set the month.
AJUSTE DEL RELOJ 28.
9. 2001 V I E
12 : 0 0 AM
OK
1
2
3
4
5
6
7
8
9
SELECCIONAR AJUSTAR FIN
4 PLAY
0
OK
Set the year, hour, and minute in sequence, using , to select the item to be set, and M/m to select the digits.
: [B b] : [V v] : [ OK ]
AJUSTE DEL RELOJ 28.
9. 2001 V I E
6 : 0 0 PM
The day of the week is set automatically. SELECCIONAR AJUSTAR FIN
5 MENU
: [B b] : [V v] : [ OK ]
Press OK to start the clock. PLAY OK
OK M/m/,
1
MENU
Press MENU, then press M/m to move the cursor (B) to AJUSTE DEL RELOJ and press OK.
PLAY
www 2
PLAY
1.
1 . 2 0 0 1 LUN
: [B b] : [V v] : [ OK ]
AJUSTE DEL RELOJ
The day of the week is set automatically.
.
12 : 0 0 AM
xiaoy u163. com
Press M/m to set the date.
OK
Note • The menu disappears automatically if you don’t proceed for more than a few minutes.
AJUSTE DEL RELOJ
SELECCIONAR AJUSTAR FIN
OK
Tip • To change the digits during the setting, press < to return to the item to be changed, and select the digits by pressing M/m.
28.
1 . 2 0 0 1 DOM
SELECCIONAR AJUSTAR FIN
12 : 0 0 AM
: [B b] : [V v] : [ OK ]
continued
Getting Started
23
24
Getting Started
– 1-5 –
http://www.xiaoyu163.com
376315150 892498299
Step 7: Setting the clock (continued)
Getting Started
376315150 892498299
Step 7
QQ
QQ
QQ 376315150 892498299
TEL 13942296513
13942296513
13942296513
1
CAN 1 4
ANTENA / CABLE ANT • CABLE SINTONIA AUTOMATICA – •+ SINT. MANUAL AFT • SI NO SINTONIA FINA.
TEL
TEL
OK
: [V v] : [B b]
AJUSTE DE SINTONIA
AJUSTAR
MENU
CAN 1 4
AJUSTE DE SINTONIA
http://www.xiaoyu163.com
QQ 376315150 892498299 Basic Operations
Playing a tape
Playing a tape (continued)
3
Z EJECT
Press H PLAY. PLAY OK
CLEAR
1
2
3
4
5
6
Additional tasks
7
8
9
To
Press
Stop play
x STOP
Pause play
X PAUSE
Resume play after pause
X PAUSE or H PLAY
Fast-forward the tape
M FF during stop
Rewind the tape
m REW during stop
Eject the tape
Z EJECT
0
DISPLAY
M FF x STOP
To set the color system If streaks appear during playback, press COLOR SYSTEM on the VCR to conform to the system that the tape was recorded in. (Normally, the color system is correctly set whenever the tape is inserted.)
m REW
1 2
A EJECT
X PAUSE x STOP
Press COLOR SYSTEM until the indicator below appears in the display window.
PAL-N
PAL
NTSC
NTSC
To play an NTSC-recorded tape Set NTSC PB in the AJUSTES ESPECIALES according to the color system of your TV. For details, see page 56.
Turn on your TV and set it to the video channel.
If your TV is
Set NTSC PB to
Insert a tape.
PAL-N
ON PAL-N TV
The VCR turns on and starts playing automatically if you insert a tape with its safety tab removed.
NTSC 3.58
NTSC 3.58
* If you are using a multi-system TV, set the NTSC PB in the AJUSTES ESPECIALES to NTSC 3.58 for better picture quality.
Basic Operations
25
376315150 892498299
QQ 376315150 892498299 26
Basic Operations
Recording TV programs
To use the time counter Press CLEAR at the point on the tape that you want to find later. The counter in the display window resets to “0:00:00.” Search for the point afterwards by referring to the counter.
INPUT SELECT
SP VIDEO
APC
TV/VIDEO
To display the counter on the TV screen, press DISPLAY. Press DISPLAY again and the counter will disappear from the TV screen.
www
2
3
4
5
6
7
8
9
0
CH +/– DISPLAY REC SPEED
Basic Operations
Notes • The counter resets to “0:00:00” whenever a tape is reinserted. • The counter stops counting when it comes to a portion with no recording. • If a tape has portions recorded in both PAL-N and NTSC systems, the time counter reading will not be correct. This is due to the difference between the counting cycles of the two color systems. • Depending on your TV, the following may occur while playing an NTSC-recorded tape: – the picture is black and white – the picture shakes – no picture appears on the TV screen – black streaks appear horizontally on the TV screen – the color density increases or decreases. • Tapes recorded in the LP mode of other NTSC system VCRs can be played back on this VCR but the picture quality cannot be guaranteed. • While setting the menu on the TV screen, you cannot use the H PLAY, X PAUSE, M FF, m REW, or x STOP button.
1
z REC
x STOP
1
Turn on your TV and set it to the video channel.
xiaoy u163. com To record from a cable box, turn it on.
2
.
Basic Operations
27
28
Insert a tape with its safety tab in place.
Basic Operations
– 1-6 –
http://www.xiaoyu163.com
376315150 892498299
TEL 13942296513
QQ
QQ
continued
13942296513
13942296513
COLOR SYSTEM
If your tape was recorded in
TEL
TEL
H PLAY H PLAY M FF
Basic Operations
X PAUSE
m REW
When the tape reaches the end, it will rewind automatically.
http://www.xiaoyu163.com
QQ 376315150 892498299 Recording TV programs (continued)
3
Press CH +/– to select the channel you want to record.
• CH
To watch another TV program while recording 1 Press TV/VIDEO to turn off the VIDEO indicator in the display window.
SP VIDEO
4
APC
Press REC SPEED to select the tape speed. (SP or LP for the PAL-N color system, and SP or EP for the NTSC color system)
REC SPEED
LP (Long Play) provides recording time twice as long as SP (Standard Play). EP (Extended Play) provides recording time three times as long as SP. However, SP produces better picture and audio quality. LP VIDEO
APC
13942296513
To check the remaining tape length Press DISPLAY. The white bar indicates the approximate length of tape remaining.
C
F
0 : 00 : 22
Remaining tape length Time counter
Tape speed*
TEL 13942296513
29
30
Recording TV programs using the Easy Timer function (continued)
Recording TV programs using the Easy Timer function The Easy Timer function allows you to make a timer recording of a program without turning on your TV. Set the recording timer to record only one program that will be broadcast within the next 24 hours using the EASY TIMER knob. If the VCR clock has not been set, you can also set the clock before setting the timer recording.
Basic Operations
2 1
2
3
4
5
6
7
8
9
Set the recording start time by turning the EASY TIMER knob clockwise or counterclockwise to increase or decrease the time by 15 minutes.
CLEAR
Press CHANNEL +/– to inrease or decrease the time by a minute.
Number buttons
Press ENTER (AM/PM) to change AM and PM.
3
ENTER (AM/PM) EASY TIMER CH +/–
0
EASY TIMER
EASY TIMER
SP
START AM APC
Push the EASY TIMER knob to confirm the start time setting. The STOP indicator appears.
SP PM
STOP APC
Setting the Easy Timer
4
Basic Operations
REC SPEED
Before you start… • When using a cable box, turn it on. • Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording time.
EASY TIMER
Set the recording stop time in the same way as in step 2, then push the EASY TIMER knob. A channel number flashes.
APC
5
CHANNEL +/–
EASY TIMER
Turn the EASY TIMER knob clockwise or counterclockwise to select the channel you want to record. To select the tape speed, press REC SPEED.
REC SPEED SP/LP (SP/EP)
1
SP
SP LP
APC
REC SPEED SP/LP
EASY TIMER knob
(SP/EP)
EASY TIMER
www
Push the EASY TIMER knob.
xiaoy u163. com 6
The START indicator appears in the display window. If the clock has not been set, “–:– –” appears. Go to step 2 in “Setting or changing the Easy Clock” on page 33.
.
SP
EASY TIMER
continued
Basic Operations
Push the EASY TIMER knob to confirm the setting. The t indicator appears in the display window and the VCR stands by for recording.
START AM APC
31
32
Basic Operations
– 1-7 –
http://www.xiaoyu163.com
AM
376315150 892498299
376315150 892498299
QQ 376315150 892498299
continued
Basic Operations
QQ
QQ
* Appears for a few seconds when the ON SCREEN DISPLAY is pressed and when the mode is changed.
13942296513
Notes • The display doesn’t appear during still (pause) mode or slow-motion playback. • If a tape has portions recorded in both PAL-N and NTSC systems, the time counter reading will not be correct. This discrepancy is due to the difference between the counting cycles of the two color systems. • When you insert a non-standard commercially available tape, the remaining time may not be correct. • It may take up to one minute for the VCR to calculate and display the remaining tape length after you press DISPLAY.
TEL
TEL
LP VIDEO
Tips • To select a channel, you can use the number buttons on the remote commander. Enter the channel number, then press ENTER. • You can select a video source from the LINE-1 IN or LINE-2 IN (SLV-EX90S AR/ EX80S AR only) jacks using the INPUT SELECT or CH +/– buttons. • The display appears on the TV screen indicating information about the tape, but the information won’t be recorded on the tape. • If you don’t want to watch TV while recording, you can turn off the TV. When using a cable box, make sure to leave it on. • You can have the VCR stop recording automatically after starting at a specified time. For details, see “Setting the recording duration time” on page 47.
To stop recording Press x STOP.
SP
Select another channel on the TV.
Safety tab
The recording indicator lights up red in the display window. Recording indicator
3
APC
Press z REC to start recording.
REC
If the TV is connected to the VCR using an audio/video cable, set the TV to TV input. If the TV is connected to the VCR using only the antenna cable, skip this step.
To save a recording To prevent accidental erasure, break off the safety tab as illustrated. To record on the tape again, cover the tab hole with adhesive tape.
Basic Operations
5
2
http://www.xiaoyu163.com
QQ 376315150 892498299 Recording TV programs using the Easy Timer function (continued)
Setting or changing the Easy Clock
When “–:– –” is displayed in the VCR’s display window, the VCR clock has not been set. You need to set the clock using the Easy Clock function before setting the timer. You can also change the current time using the Easy Clock function.
1
2
3
4
5
6
7
8
9
3
To continue the Easy Timer setting, go to step 2 in “Setting the Easy Timer” on page 31.
ENTER (AM/PM) EASY TIMER CH +/–
0
EASY TIMER
To set the timer and clock setting using the remote commander You can also use the remote commander to set the Easy Timer and Easy Clock. The operations on the VCR and the remote commander correspond as follows:
Set the current time using the EASY TIMER knob. 1 Turn the EASY TIMER knob clockwise or counterclockwise to enter the current hour. 2 Push the EASY TIMER knob to confirm the hour setting. 3 Turn the EASY TIMER knob to increase or decrease the minutes setting by a minute. Press ENTER (AM/PM) to SP CLOCK START AM APC change AM and PM.
To
Do this on the VCR
Do this on the remote commander
Confirm the setting and go to the next setting
Push the EASY TIMER knob
Press EASY TIMER
Change the time by 15 minutes (in START/STOP mode)
Hold CH +/– down Turn the EASY TIMER knob or hold CHANNEL +/– down
Change the time by one minute (in START/STOP mode)
Press CHANNEL +/–
Press CH +/–
Select the channel
Turn the EASY TIMER knob or press CHANNEL +/–
Press CH +/– or INPUT SELECT
Change the hour/minute by one hour/minute (in CLOCK mode)
Turn the EASY TIMER knob or press CHANNEL+/–
Press CH +/–
You can also use the number buttons to set the clock, start and stop times, and the channel you want to record. Just press the number buttons to enter the hours and minutes. For example: • To set the clock to “8:20”, press 0, 8, EASY TIMER , 2, 0 and EASY TIMER in sequence. • To set the start or stop time to “8:20”, press 0, 8, 2, 0 and EASY TIMER in sequence.
Basic Operations
33
34
Basic Operations
Recording TV programs using the Easy Timer function (continued) To stop recording To stop the VCR while recording, press x STOP.
Tips • To record from a source connected to the LINE-1 IN or LINE-2 IN (SLV-EX90S AR/ EX80S AR only) jacks, press INPUT SELECT or CH +/– or turn the EASY TIMER knob to display “L1” or “L2” (SLV-EX90S AR/EX80S AR only) in the display window. • To record NTSC signals, set the tape speed to SP or EP. To set to the EP mode, display “LP” in the display window.
To check or change the timer setting Push the EASY TIMER knob repeatedly until the setting you want to check or change flashes. Then re-enter the new setting, if necessary. If you do not want to change any of the settings, push the EASY TIMER knob repeatedly until the t indicator appears in the display window.
Notes • You cannot set the Easy Timer if eight programs have already been set. • You can set the timer for only one program using the Easy Timer function. If you want to set the timer for other programs, use the PROGRAM./VERIF. menu. For details, see page 37. • You cannot set the date using the Easy Timer function. Set the date using the AJUSTE DEL RELOJ menu if you want to set the timer with the menu. For details, see page 23. • The t indicator flashes in the display window when you complete the setting with no tape inserted.
You can also change the timer setting using the PROGRAM./VERIF. menu. For details, see page 50. To cancel the timer setting To cancel the Easy Timer setting while entering a setting, press CLEAR on the remote commander or press CHANNEL + and – on the VCR at the same time.
You can also do the following tasks while the VCR is recording: • • • •
Reset the counter. Display tape information on the TV screen. Check the timer settings. Watch another TV program.
Basic Operations
To use the VCR after setting the timer To use the VCR before a timer recording begins, just press ?/1. The t indicator turns off and the VCR switches on. Remember to press ?/1 to reset the VCR to the timer recording standby mode after using the VCR.
To watch the recorded program right after recording with the Easy Timer The SEARCH MODE indicator starts flashing when the VCR finishes the Easy Timer recording. To watch the recorded program, push the EASY TIMER knob. The VCR turns on, starts searching, then automatically starts playback from the beginning of the recording. For details, see page 40.
www
.
xiaoy u163. com continued
Basic Operations
35
36
Basic Operations
– 1-8 –
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 376315150 892498299
QQ
QQ
TEL 13942296513
If you make a mistake, re-enter the correct digits before pressing EASY TIMER .
continued
13942296513
13942296513
EASY TIMER
START STOP PM APC
TEL
TEL
SP CLOCK START AM APC
SP
To quit the Easy Timer setting mode without changing any settings, push the EASY TIMER knob repeatedly until the t indicator appears in the display window.
Basic Operations
• When “–:– –” is displayed in the display window, push the EASY TIMER knob. • To change the clock setting, push and hold the EASY TIMER knob on the VCR for more than three seconds. The CLOCK indicator and the current clock setting appear in the display window.
2
Push the EASY TIMER knob to finish setting the clock. The VCR enters the timer recording setting mode.
Number buttons
EASY TIMER knob
1
EASY TIMER
http://www.xiaoyu163.com
QQ 376315150 892498299 Setting the timer manually
Setting the timer manually (continued)
2
?/1
PLAY
You can preset up to eight programs at a time. Before you start… • Check that the VCR clock is set to the correct time. • Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording time. • Turn on your TV and set it to the video channel.
OK
INPUT SELECT
1
2
3
4
5
6
7
8
9
Set the date, start and stop times, channel number, and tape speed: 1 Press , to select each item in turn. 2 Press M/m to set each item. To correct a setting, press < to return to that setting and reset it.
PROGRAM. / VERIF. 28. 9 VIE FECHA INICIO FIN CANAL 3 0 . 9 DOM – : – – – : –– – – SP ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– –
To record the same program every day or the same day every week, press m while the date is flashing. For details, see “Daily/weekly recording” on page 39.
0
INPUT SELECT
CH +/–
3 TEL
OK M/m/,
Press , to confirm the setting. PLAY OK
4
The cursor (B) appears at the beginning of the line. To enter another setting, move the cursor to the next line and repeat step 2.
TEL
Basic Operations
MENU
To record from a source connected to the LINE-1 IN or LINE-2 IN (SLV-EX90S AR/EX80S AR only) jacks, press INPUT SELECT or CH +/– to display “L1” or “L2” (SLV-EX90S AR/EX80S AR only) in the “CANAL” position.
Press OK. PLAY OK
• ]/1
Press ?/1 to turn off the VCR. The t indicator appears in the display window and the VCR stands by for recording.
1
To record from other equipment, leave the connected equipment switched on. Press MENU and select PROGRAM./ VERIF., then press OK.
MENU
PLAY
PROGRAM. / VERIF. 28. 9 VIE FECHA INICIO FIN CANAL ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– –
To stop recording To stop the VCR while recording, press x STOP.
OK
37
38
Basic Operations
Search Operations
Searching for the beginning of an Easy Timer recorded program
Daily/weekly recording In step 2 above, press m to select the recording pattern. Each time you press m, the indication changes as shown below. Press M to change the indication in reverse order.
If you record a program using the Easy Timer function, you can easily find the beginning of the recording with the SEARCH MODE function. The SEARCH MODE indicator flashes when the VCR finishes making an Easy Timer recording.
the current date t DOM-SAB (Sunday to Saturday) t LUN-SAB (Monday to Saturday) t LUN-VIE (Monday to Friday) t TODOS SAB (every Saturday) t ..... t TODOS LUN (every Monday) t TODOS DOM (every Sunday) t 1 month later t (dates count down) t the current date Tips • To set the channel, you can also use the CH +/– or number buttons. • To set the tape speed, you can also use the REC SPEED button. • To record NTSC signals, set the tape speed to SP or EP. To set to the EP mode, display “LP” in the tape speed position.
SEARCH MODE
Push the EASY TIMER knob.
Note • The t indicator flashes in the display window when you press ?/1 with no tape inserted.
The VCR turns on, rewinds to the beginning of the recorded program and starts playback automatically. The SEARCH MODE indicator turns off.
Basic Operations
Tip • You can start the SEARCH MODE function after the flashing of the SEARCH MODE indicator has been stopped. The flashing stops when you turn on the VCR and press the SEARCH MODE button (Do not press any button at this point, otherwise this SEARCH MODE function will be canceled). To start the SEARCH MODE function, press the SEARCH MODE button repeatedly until the SEARCH MODE indicator flashes. Push the EASY TIMER knob. The VCR rewinds and starts playback automatically. If you continue to press the SEARCH MODE button while the SEARCH MODE indicator is flashing, you can enter other search operations (For details, see the following pages). Each press of the SEARCH MODE button changes the search operations as follows:
REMAIN
www
EASY TIMER knob
BLANK
INDEX
TIME
Off
Note • This SEARCH MODE function will be canceled (the SEARCH MODE indicator turns off) if: – The VCR starts recording other programs. – You press the H PLAY, M FF, m REW or A EJECT button while the VCR is on.
.
xiaoy u163. com Basic Operations
39
40
Search Operations
– 1-9 –
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 376315150 892498299
QQ
QQ
TEL 13942296513
continued
Basic Operations
13942296513
13942296513
5
http://www.xiaoyu163.com
QQ 376315150 892498299 Searching for the current position on a tape
Searching using the Blank Search function
EASY TIMER knob
This feature enables you to find the current position on a tape as well as the remaining time of the tape.
EASY TIMER knob
This feature enables you to find a blank section on your tape. SEARCH MODE
SEARCH MODE
Press SEARCH MODE repeatedly until the REMAIN indicator appears in the display window as shown on the right.
SP
START APC
n SP
2
START
START APC
––––––––––––––––
APC
To stop searching To stop the VCR while searching for a blank section, press x STOP.
0:15 (remaining time of the tape)
Notes • To display the remaining time correctly you may have to select the SELEC DE CINTA in the AJUSTES ESPECIALES according to the type of the tape that you are using. For details, see page 56. • In step 2, “FULL” will appear in the display window for about one minute, if: – there is no blank section available on the tape. – the remaining time of a blank section is less than one minute. • The VCR can only detect the blank section between the end of the tape and the end of the last recorded program.
To stop the Search function Press x STOP.
Blank section
Last recorded program
41
42
Searching using the index function
Search Operations
Searching using the index function (continued)
Using the SEARCH MODE button and EASY TIMER knob on the VCR
EASY TIMER knob
./> INDEX SEARCH
The VCR marks the tape with an index signal at the point where each recording begins. Use these signals as references to find a specific recording. The VCR can search up to 99 index signals ahead of or behind the current position. You can either use the INDEX SEARCH buttons on the remote commander or the SEARCH MODE button and EASY TIMER knob on the VCR.
SEARCH MODE
1
Press SEARCH MODE on the VCR repeatedly until “INDEX” appears in the VCR’s display window (the SEARCH MODE indicator lights up). SP
Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel.
2
APC
Turn the EASY TIMER knob to specify how many index signals ahead or behind you want to search: • To search ahead, turn the EASY TIMER knob clockwise. • To search backwards, turn the EASY TIMER knob counterclockwise.
Using the INDEX SEARCH buttons on the remote commander
1 2
SP
APC
3
Insert an indexed tape into the VCR. Press ./> INDEX SEARCH repeatedly to specify how many index signals ahead or behind you want to search: • To search ahead, press > INDEX SEARCH.
To stop searching Press x STOP.
xiaoy u163. com
The VCR starts searching and the index number on the TV screen counts down to zero. Playback starts from the point about five seconds ahead of the specified index mark.
.
Push the EASY TIMER knob. The VCR starts searching. Playback starts (the SEARCH MODE indicator turns off) from the point about five seconds ahead of the specified index mark.
INDICE 8 BUSQUEDA
• To search backwards, press . INDEX SEARCH.
www
START
Note • No index signal will be added when recording starts from recording pause. However, an index signal will be marked if you change the channel during recording pause.
continued
Search Operations
43
44
Search Operations
– 1-10 –
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 376315150 892498299 End of tape
QQ
QQ
Notes • To display the remaining time correctly you may have to select the SELEC DE CINTA in the AJUSTES ESPECIALES according to the type of the tape that you are using. For details, see page 56. • In step 2, the VCR automatically rewinds and fast-forwards the tape only if you press the SEARCH MODE button right after you insert a tape. This is so that the VCR can measure the current position on the tape. • You cannot use this function during any recording mode. Search Operations
APC
13942296513
13942296513
Tape meter
“REMAIN” and the remaining time of the tape appear in the display window in the following order:
TEL 13942296513
START
“BLANK” and the remaining time of the blank section appear alternately in the display window for about one minute.
POSICIÓN DE LA CINTA
MAIN
SP
TEL
TEL
Push the EASY TIMER knob to display the tape meter on the TV screen. The SEARCH MODE indicator turns off. A cursor (x) indicates the current position on the tape.
Push the EASY TIMER knob on the VCR. The SEARCH MODE indicator turns off. The VCR fast-forwards to the end of the tape. Then, the VCR rewinds the tape to the last recorded program. After a few seconds, the VCR starts playback and stops at the beginning of the blank section.
APC
RE-
SP
The SEARCH MODE indicator lights up.
The SEARCH MODE indicator lights up.
2
Press SEARCH MODE repeatedly until the BLANK indicator appears in the display window.
n
1
1
http://www.xiaoyu163.com
QQ 376315150 892498299 Additional Operations
Searching using the Time Search function EASY TIMER
Playing/searching at various speeds
knob
You can easily find a specific point on a tape by using the Time Search function. For example, you can find a recorded section 15 minutes ahead of or behind the current position of a tape by using the Time Search function.
×2 H PLAY m REW
y SLOW
M FF
SEARCH MODE
H PLAY M FF
1
Press SEARCH MODE repeatedly until “TIME” appears in the display window (the SEARCH MODE indicator lights up).
m REW
SP APC
2
Turn the EASY TIMER knob clockwise or counterclockwise to set the length of time you want the VCR to fast-forward or rewind the tape. Each turn on the knob increases or decreases the duration by 15 minutes.
To change the time by one minute, press CHANNEL +/–.
APC
Push the EASY TIMER knob.
During fast-forward, hold down M FF down. During rewind, hold down m REW.
Play at high speed
• During playback, press M FF or m REW on the remote commander. • During playback, hold down M FF or m REW. When you release the button, normal playback resumes.
Play at twice the normal speed
During playback or pause, press × 2.
Play in slow motion
During playback or pause, press y SLOW.
Play frame by frame
During pause, press M FF or m REW on the remote commander. Hold down the button to play one frame each second.
Rewind and start play
While the tape is stopped, hold down 0 REW on the VCR and press H PLAY on the VCR.
The VCR starts searching and the tape counter starts counting until it reaches the specified point.
To resume normal playback Press H PLAY.
SP APC
Tips • Adjust the picture using the TRACKING +/– buttons on the VCR if: – streaks appear while playing in slow motion. – the picture shakes during pause. To set tracking to the center position, press both buttons (+/–) at the same time. • If noise appears during pause or frame-by-frame playback, first switch to the slow motion playback, then adjust the picture using TRACKING +/– on the VCR.
The VCR starts playback automatically when the tape counter reaches the specified point (the SEARCH MODE indicator turns off). To stop searching Press x STOP.
Setting the recording duration time
Search Operations
45
46
Additional Operations
Synchronized recording (SLV-EX90S AR only)
After you have started recording in the normal way, you can have the VCR stop recording automatically after a specified duration.
1
2
3
4
5
6
7
8
9
The Synchronized Recording feature enables you to record from the connected equipment such as a satellite tuner, a cable TV decoder or a TV that has a timer function. Once you set the timer on the other equipment, the VCR will start recording the program synchronized with the timer.
0
Connections necessary to use this function Connect the other equipment to the LINE-1 IN jacks of this VCR. This VCR (Recorder)
z REC
1
Satellite tuner, etc.
LINE-1 IN
While recording, press z REC.
LINE OUT
The t indicator appears in the display window. SP VIDEO
APC
VMC-810HG audio/video cable (not supplied)
2
: Signal flow
Press z REC repeatedly to set the duration. Each press advances the time in increments of 30 minutes. 0:30
1:00
5:30
6:00
How to make a Synchronized recording
Normal recording
SYNCHRO REC
The tape counter decreases minute by minute to 0:00, then the VCR stops recording and turns off automatically. To extend the duration Press z REC repeatedly to set to the new duration.
www
xiaoy u163. com REC SPEED SP/LP (SP/EP)
To cancel the duration Press z REC repeatedly until the t indicator turns off and the VCR returns to normal recording mode. To stop recording To stop the VCR while recording, press x STOP.
.
Additional Operations
47
48
1
Press INPUT SELECT or CH +/– on the remote commander to display “L1” in the display window.
2
Set the timer on the equipment to the time of the program you want to record, then turn it off.
3
Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording time.
Additional Operations
– 1-11 –
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 376315150 892498299
TEL 13942296513
QQ
QQ
Notes • The sound is muted during these operations. • In LP or EP mode, noise may appear or there may be no color. • The picture may show noise when playing at high speed in reverse.
Tip • The VCR can search up to three hours ahead of or behind the current position of a tape.
13942296513
13942296513
3
SP
Operation
View the picture during fastforward or rewind
TEL
TEL
For example, if you want to watch a recorded section 15 minutes ahead of the current position, turn the EASY TIMER knob once clockwise.
Playback options
http://www.xiaoyu163.com
QQ 376315150 892498299 4
Press REC SPEED to select the tape speed (SP or LP for the PAL-N color system, and SP or EP for the NTSC color system).
5
Hold down SYNCHRO REC for more than two seconds.
Checking/ changing/ canceling timer settings
The SYNCHRO REC button lights up and the VCR stands by for recording.
?/1
The VCR automatically turns on and starts recording when it receives video/audio signals from the connected equipment.
CLEAR
Before you start… • Turn on your TV and set it to the video channel.
To cancel the Synchronized recording Press SYNCHRO REC so that the button’s light turns off.
1
2
3
4
5
6
7
8
9
To stop recording Press x STOP while recording.
0
The VCR automatically stops recording when the tape reaches the end or when the other equipment stops transmitting the video/audio signals. MENU
OK M/m/,
Press ?/1 to turn on the VCR. Press MENU, then press M/m to select PROGRAM./VERIF. and press OK:
PROGRAM. / VERIF. 28. 9 VIE FECHA INICIO FIN CANAL 3 0 . 9 DOM 8 : 0 0 PM 9 : 0 0 PM 3 5 SP 2 . 10 MAR 10 : 0 0 AM 11 : 3 0 AM 2 0 LP 2 : 0 0 PM 3 : 0 0 PM 6 0 LP LUN – VIE TODOS DOM 6 : 3 0 AM 7 : 0 0 AM 4 2 LP ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– – ––. – – : –– – : –– –– –
• If you want to change or cancel a setting, go on to the next step. • If you do not need to change or cancel the settings, press OK, then turn off the VCR to return to recording standby.
Additional Operations
QQ 376315150 892498299 50
Additional Operations
Recording stereo and bilingual programs (SLV-EX90S AR/EX80S AR only)
Press M/m to select the setting you want to change or cancel: • To change the setting, press , to select the item you want to change, and press M/m to reset it. Then, press , repeatedly until the cursor (”) appears at the beginning of the line. • To cancel the setting, press CLEAR.
4
Press OK.
Recording stereo programs
If any timer settings remain, turn off the VCR to return to recording standby.
This VCR automatically receives and records stereo programs. When a stereo program is received, the STEREO indicator lights up. If there is noise in the stereo program, set AUTO ESTEREO in the AJUSTES ESPECIALES to NO. The sound will be recorded in monaural (on both hi-fi and normal audio tracks) but with less noise. For details, see page 56.
When the timer settings overlap The program that starts first has priority and the second program starts recording only after the first program has finished. If the programs start at the same time, the program listed first in the menu has priority.
Recording bilingual programs Normally, this VCR records only the main sound. When a SAP (Second Audio Program) is received, the SAP indicator appears on the TV screen for a few seconds. To record only SAP sound, set SELEC. AUDIO in the AJUSTES ESPECIALES to SAP. For details, see page 56.
Program 1 Program 2 will be cut off
Selecting the sound during playback Press AUDIO MONITOR to select the sound you want. (If you are recording, the sound being recorded will not change.) To listen to
On-screen display
Display window
Stereo
ESTEREO
STEREO
Left channel
CAN. I
STEREO
Right channel
CAN. D
STEREO
Monaural sound on the normal audio track*
No indicator
No indicator
* Usually the mixed sound of left and right channels (monaural)
www
.
xiaoy u163. com Additional Operations
51
52
Additional Operations
– 1-12 –
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
3
49
QQ
QQ
TEL 13942296513
13942296513
13942296513
1 2
TEL
TEL
Notes • Some TVs or other equipment automatically turn off in a certain amount of time if you do not operate it after it turns on with the timer. In this case the Synchronized Recording also stops automatically. • The Synchronized Recording starts and stops according to the signals from the connected equipment. Refer also to the instruction manual of the connected equipment for information about its timer function. • Some equipment keeps transmitting signals even though the power is off. In this case, the Synchronized Recording feature does not work because the VCR will not be able to know when to start recording. To record the program, set the timer on the VCR. If you use a satellite tuner or a cable TV decoder, make sure to turn it on. For details, see “Setting the timer manually”. • If the settings for timer recording and Synchronized Recording overlap, the program that starts first has priority and the second program starts recording only after the first program has finished. • To record NTSC signals, set the tape speed to SP or EP. To record in the EP mode, set the tape speed to “LP”.
http://www.xiaoyu163.com
QQ 376315150 892498299 Adjusting the picture
How sound is recorded on a video tape
The VCR records sound onto two separate tracks. Hi-fi audio is recorded onto the main track along with the picture. Monaural sound is recorded onto the normal audio track along the edge of the tape. Normal audio track
Adjusting the tracking
Although the VCR automatically adjusts the tracking when playing a tape (the indicator flashes in the display window, then turns off), distortion may occur if the recording is in poor condition. In this case, manually adjust the tracking.
Monaural sound
Hi-fi audio track (main track)
Press the TRACKING +/– buttons on the VCR to display the tracking meter. The distortion should disappear as you press one of the two tracking buttons (the indicator lights up). To resume automatic tracking adjustment, eject the tape and re-insert it.
Stereo sound (left/right channels) Notes • To play a tape in stereo, you must use the A/V connections. • When you play a tape recorded in monaural, the sound is heard in monaural regardless of the AUDIO MONITOR setting. • If the AUDIO MONITOR button does not function, check that MEZCL. AUDIO in the AJUSTES ESPECIALES is set to NO. For details, see page 56.
TRACKING NORMAL
Tracking meter
About the R2 (Reality Regenerator) function (SLVEX90S AR only)
When playback starts, the R2 function activates and the R2 button lights up.
R2
REAL (status of playback started)
53
54
Additional Operations
Changing menu options
AJUSTES ESPECIALES AUTO ANT SE L • S I NO AUTO ESTEREO • S I NO MEZCL. AUD I O SI • NO SELEC. AUD I O • MAIN SAP • SI APC NO NTSC PB • ON PA L - N TV NTSC 3 . 58 SELEC DE CINTA • AUTO 1 80 SELECCIONAR : [ V v ] AJUSTAR : [B b]
1
Press MENU, then select AJUSTES ESPECIALES. SLV-EX90S AR/EX80S AR AJUSTES ESPECIALES AUTO ANT SEL • SI NO AUTO ESTEREO • SI NO MEZCL. AUDIO SI • NO SELEC. AUDIO • MAIN SAP • SI APC NO NTSC PB • ON PAL - N TV NTSC 3. 58 SELEC DE CINTA • AUTO 1 80 SELECCIONAR : [ V v ] AJUSTAR : [B b]
APC playback The APC function automatically works on all types of tapes, including rental tapes and tapes that were not recorded with APC.
2 3
APC recording Whenever you insert a tape and first start recording, the VCR adjusts to the tape using the APC function (the APC indicator flashes rapidly). This adjustment is retained until the tape is ejected.
AJUSTES ESPECIALES AUTO ANT SEL • S I NO APC • SI NO NTSC PB • ON PA L - N TV NTSC 3 . 58 SELEC DE CINTA • AUTO 1 80
SELECCIONAR AJUSTAR
: [V v] : [B b]
Press M/m to select the option, then press , to change the setting. Press OK to return to the original screen.
Menu choices Initial settings are indicated in bold print.
To deactivate the APC function Set APC to NO in the AJUSTES ESPECIALES. The APC indicator in the display window turns off. Tip • To set the tracking to the center position, press the TRACKING + and – buttons at the same time. Note • There is a delay of a few seconds before the VCR actually starts recording while the VCR analyzes the tape. To avoid the delay, first set the VCR to recording pause (the APC indicator flashes slowly) and press z REC to have the VCR analyze the tape (the APC indicator flashes rapidly). After the APC indicator stops flashing, press X PAUSE to start recording immediately. If you press X PAUSE before the APC indicator stops flashing, the APC function is cancelled.
Menu option
Set this option to
AUTO ANT SEL
SI if your TV is connected only to VHF/UHF OUT on the VCR. To play a tape, set the TV to the VCR channel (channel 3 or 4). NO if your TV is connected to both VHF/UHF OUT and LINE OUT on the VCR. To play a tape, set the TV to the VCR input.
AUTO ESTEREO (SLV-EX90S AR/ EX80S AR only)
SI to receive stereo programs. NO to reduce noise. The sound changes to monaural.
MEZCL. AUDIO (SLV-EX90S AR/ EX80S AR only)
SI to listen to the hi-fi and normal audio tracks at the same time. The AUDIO MONITOR button will not function. NO to listen to the hi-fi and normal audio tracks separately. Select the sound using the AUDIO MONITOR button. For details, see page 52.
SELEC. AUDIO (SLV-EX90S AR/ EX80S AR only)
MAIN to record the main sound. SAP to record the SAP (Second Audio Program) sound.
APC
SI to switch on the APC (Adaptive Picture Control) function and improve picture quality. NO to switch off APC.
NTSC PB
ON PAL-N TV to play back an NTSC-recorded tape on a PAL-N TV. NTSC 3.58 to playback an NTSC-recorded tape on an NTSC TV. For details, see page 26.
SELEC DE CINTA
AUTO when using a T-160 length tape or any tape shorter than a T-140 length tape 180 when using a T-140 or T-180 length tape.
xiaoy u163. com Additional Operations
SLV-EX50 AR
55
56
Additional Operations
– 1-13 –
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
The Adaptive Picture Control (APC) function automatically improves recording and playback quality by adjusting the VCR to the condition of the video heads and tape. To maintain better picture quality, we recommend that you set APC to SI in the AJUSTES ESPECIALES (The APC indicator lights up in the display window). For details, see page 56.
QQ
QQ
Additional Operations
About the Adaptive Picture Control (APC) function
.
DYNA (dynamic)
QQ 376315150 892498299
TEL 13942296513
www
SOFT
13942296513
13942296513
Each press of the button changes the effect and indication in the display window as follows:
TEL
TEL
The R2 function automatically adjusts the picture to the most suitable quality during playback.
http://www.xiaoyu163.com
QQ 376315150 892498299 Editing with another VCR
Editing with another VCR (continued)
How to connect to a stereo system (SLV-EX90S AR/ EX80S AR only)
How to connect to record on this VCR
Connect the LINE-1 IN AUDIO R/L or LINE-2 IN AUDIO L/R jacks on this VCR to the audio output jacks on the stereo system, using the RK-C510HG audio cable (not supplied).
For SLV-EX90S AR and EX80S AR only TV
This VCR (Recorder)
Tips • (For SLV-EX50 AR only) Use commercially available connecting cable such as the Sony VMC-710HG/720HG (2-phono to 2-phono). If the other VCR has the AUDIO L and R jacks, use a connecting cable such as the Sony VMC-910HG (3-phono to 2-phono). • (For SLV-EX90S AR/EX80S AR only) If the other VCR is a monaural type, the sound is recorded only on the channel whose jack is connected to the audio plug. To record on both right and left channels, connect the audio plugs to the AUDIO R/L jacks using a VMC-910HG (3-phono to 2-phono) audio/video cable (not supplied).
Other VCR (Player) LINE-1 IN LINE OUT
VMC-810HG audio/video cable (not supplied)
TEL
For SLV-EX50 AR only TV
This VCR (Recorder)
13942296513
13942296513
Other VCR (Player) LINE-1 IN LINE OUT
VMC-710HG/720HG audio/video cable (not supplied) : Signal flow
57
58
Additional Operations
Additional Information
General setup information
Operation (when recording on this VCR)
Attaching the external antenna connector
Before you start editing • Turn on your TV and set it to the video channel. • Press INPUT SELECT or CH +/– to display “L1” or “L2” (SLV-EX90S AR/ EX80S AR only) in the display window. • Press REC SPEED to select the tape speed (SP or LP for the PAL-N system, and SP or EP for the NTSC system).
When using a 300-ohm twin lead cable for aVHF/UHF antenna, use the EAC-32 antenna connector (not supplied) to connect the antenna to the VCR.
X PAUSE
1 2 3
z REC
1
Insert a source tape with its safety tab removed into the other (playback) VCR. Search for the point to start playback and set it to playback pause.
2
Insert a tape with its safety tab in place into this (recording) VCR. Search for the point to start recording and press X PAUSE.
3 4
Press z REC on this VCR to set it to recording pause.
300-ohm twin lead cable
EAC-32 antenna connector (not supplied)
Loosen the screws on the antenna connector. Wind the twin leads around the screws on the antenna connector. Retighten the screws.
Attaching a UHF/VHF band mixer
300-ohm twin lead cable
When using both a 75-ohm coaxial cable and a 300-ohm twin lead cable for a VHF/UHF antenna, use the EAC-66 UHF/VHF band separator/mixer (not supplied) to connect the antenna to the VCR.
To start editing, press the X PAUSE buttons on both VCRs at the same time.
EAC-66 UHF/VHF band separator/ mixer (not supplied)
To stop editing Press the x STOP buttons on both VCRs. Tips • To edit more precisely, press the X PAUSE buttons on the VCRs to release pause. • To cut out unwanted scenes while editing, press X PAUSE on this VCR when an unwanted scene begins. When it ends, press X PAUSE again to resume recording.
75-ohm coaxial cable
1 2 3 4
Note • If you start recording following the procedure above, the VCR won’t start recording with the APC function. To record a tape with the APC function, press z REC again during recording pause in step 3 so that the VCR analyzes the tape. Then, press X PAUSE after the APC indicator stops flashing to start recording. If you press X PAUSE before the APC indicator stops flashing, the APC function is canceled.
.
Loosen the screws on the mixer. Wind the twin leads around the screws on the mixer. Retighten the screws.
xiaoy u163. com Additional Operations
59
60
Connect the 75-ohm coaxial cable to the mixer.
Additional Information
– 1-14 –
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 376315150 892498299
QQ
QQ
TEL 13942296513
continued
Additional Operations
www
TEL
Notes • Make sure you connect the plugs to jacks of the same color. • (For SLV-EX90S AR/EX80S AR only) When you connect a monaural VCR to the LINE-1 IN or LINE-2 IN jacks, make sure to connect the audio plug to the AUDIO L (white) jack. The sound is recorded on both right and left channels. When connecting to the AUDIO R (red) jack, the sound is recorded only on the right channel. • If you connected this VCR to both the LINE IN and LINE OUT jacks of the other VCR, select the input correctly to prevent humming noise.
http://www.xiaoyu163.com
QQ 376315150 892498299 Index to parts and controls
Index to parts and controls (continued)
Display window
Refer to the pages indicated in parentheses ( ) for details.
Front panel 2
1
!ª
!• !¶!§ !∞ !¢
STEREO SP CLOCK START STOP LP VIDEO AMPM APC EP
34 5 6
!£ !™!¡!º 987
1 Timer indicator (38) 2 STEREO indicator (52) (SLV-EX90S AR/EX80S AR only)
TEL
2 Tape compartment
qd Remote sensor (5)
3 A EJECT button (26) 4 m REW (rewind) button (26, 46)
6 M FF (fast-forward) button (26, 46)
0 Tracking indicator (54)
4 VIDEO indicator (13, 30)
qa Color system indicator (26)
5 CLOCK indicator (33)
qs Time counter/clock/line/channel indicator (27, 29, 33, 59)
6 AM/PM indicator (33)
qg REC SPEED SP (Standard Play)/LP (Long Play)/EP (Extended Play) button (29)
9 STOP indicator (32)
3 Tape speed indicator (29)
7 START indicator (31)
qd Tape/recording indicator (29)
qh COLOR SYSTEM button (26)
7 z REC (record) button (29)
qj ONE TOUCH TUNING button (16)
8 x STOP button (26)
qk R2 (Reality Regenerator) button (54) (SLV-EX90S AR only)
9 X PAUSE button (26) q; SEARCH MODE button/indicator (40, 41, 42, 44, 45) qa EASY TIMER knob (31, 40, 41, 42, 44, 45)
ql LINE-2 IN VIDEO/AUDIO L/R jacks (58) (SLV-EX90S AR/EX80S AR only)
65
66
Additional Information
Index to parts and controls (continued)
Rear panel (SLV-EX90S AR/EX80S AR) 1
2
Remote commander
3
1 TV/VIDEO remote control switch (5) 2 Z EJECT button (26) 3 TV/VIDEO button (for TV) (13, 30) 4 INPUT SELECT button (30, 38) 5 CLEAR button (27, 51)
5 1 AC power cord 2 LINE-1 IN AUDIO R/L/VIDEO jacks (57) 3 VHF/UHF IN/OUT connectors (9, 10, 11, 12)
4 4 RF (Radio Frequency) UNIT switch (13)
1
2
3
6 EASY TIMER button (34)
4
5
6
7
8
9
7 R2 (Reality Regenerator) button (54) (SLV-EX90S AR only) 8 z REC button (29, 47)
0
5 LINE OUT AUDIO/VIDEO R/L jacks (7)
9 REC SPEED button (29) 0 ×2 button (46) qa MENU button (10, 56) qs Tape/menu operation buttons
Rear panel (SLV-EX50 AR) 1
2
5
www
1 AC power cord
X PAUSE/M button (26) x STOP/m button (26) m REW (rewind)/< button (26, 46) M FF (fast-forward)/, button (26, 46) H PLAY/OK button (26)
3
4
xiaoy u163. com
2 LINE-1 IN AUDIO/VIDEO jacks (57)
4 RF (Radio Frequency) UNIT switch (13)
5 LINE OUT AUDIO/VIDEO jacks (8)
3 VHF/UHF IN/OUT connectors (9, 10, 11, 12)
.
continued
Additional Information
67
68
Additional Information
– 1-15 –
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL 13942296513
QQ
QQ
QQ 376315150 892498299
continued
Additional Information
13942296513
13942296513
5 H PLAY button (26)
qf SYNCHRO REC button (48) (SLV-EX90S AR only)
8 APC (Adaptive Picture Control) indicator (55)
TEL
qs CHANNEL/TRACKING +/– buttons (29, 54)
1 ?/1 POWER switch (13, 38)
NTSC PAL
http://www.xiaoyu163.com
QQ 376315150 892498299 qd ?/1 (power) switch (38)
qf AUDIO MONITOR button (52) (This button doesn’t work for SLVEX50 AR only)
qg Number buttons and ENTER (AM/ PM) buttons (20, 30, 33) 1
2
3
4
5
6
7
8
qh CH (channel) +/– buttons (20, 29) qj VOL (volume) +/– buttons (for TV) qk DISPLAY button (27, 29)
9
ql ./> INDEX SEARCH buttons (43)
0
w; y SLOW button (46)
TEL
TEL
13942296513
13942296513 Additional Information
.
QQ 376315150 892498299
xiaoy u163. com – 1-16E –
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
www
69
QQ
QQ
TEL 13942296513
http://www.xiaoyu163.com
SLV-EX50/EX80S/EX90S
QQ 376315150 892498299 SECTION 2 DISASSEMBLY
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. CASE, FRONT PANEL BLOCK ASSEMBLY
1 Two tapping screws
3 Upper case
TEL
TEL 2 Two tapping screws
Hooks
5 Flat Cable FDM-010
6 Flat Cable FDI-002
Hooks
2-2. DM-98 BOARD, DI-81 BOARD, FJ-31 BOARD 7 Flat Cable FDI-002 8 Two screws (B2.6 × 8)
1 Four screws (B2.6 × 8)
9 Earth Plate
0 Two screws (B2.6 × 8) 4 DI-81 board
www
xiaoy u163. com
2 DM-98 board
3 Flat Cable FDM-010
.
5 Flat Cable FDI-002
2-1
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
Hooks
Hooks 7 Front panel (Engaged by the six hooks)
6 FJ-31 board
QQ
QQ
QQ 376315150 892498299
TEL 13942296513
13942296513
13942296513
4 Flat Cable FDI-002
http://www.xiaoyu163.com
QQ 376315150 892498299
2-3. REAR PANEL
2 Rear panel (Engaged by the seven hooks) Hooks
Hooks
TEL
TEL
Hooks
1 POWER code stopper
2-4. MA-402 BOARD
2 MA-402 board with mechanism deck
www
.
xiaoy u163. com 2-2
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 376315150 892498299
TEL 13942296513
QQ
QQ
1 Six screws (Sumitite (B3) +BV)
13942296513
13942296513
Hooks
http://www.xiaoyu163.com
QQ 376315150 892498299 2-5. MECHANISM DECK
4 Flat cable FMD-022/FMD-023 5 Harness FE-141
3 Flat Cable FAC-009 6 Two screws (BVTP 3 × 12)
9 Screw (BVTP 3 × 12)
2 Screw (Sumitite (B3), +BV)
qs Mechanism deck
TEL
TEL CN331
CN202
0 MD base (R)
7 MD base (M)
8 MD base (R) Note: When mounting the mechanism deck, first align mark on the rotary switch.
www
.
xiaoy u163. com 2-3
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
qa MA-402 board
QQ
QQ
QQ 376315150 892498299
TEL 13942296513
13942296513
13942296513
1 Flexible cable
http://www.xiaoyu163.com
QQ 376315150 892498299
2-6. INTERNAL VIEWS
Drum assembly (M901) (DZH-0D0A-R) 1-796-011-11 (SLV-EX50AR) Drum assembly (M901) (DZH-0D1A-R) 1-796-012-11 (SLV-EX80SAR/EX90SAR) Drum assembly (M901) (DZH-0B4A-R) 1-772-363-11 (SLV-EX50BR) Drum assembly (M901) (DZH-0B7A-R) 1-772-366-11 (SLV-EX80SBR/EX90SBR)
FE head 1-500-471-11
ACE head assembly A-6759-720-A
D001 Tape top/end LED 8-719-066-72
M902 Capstan motor 1-763-572-11
www
x aoy u163. com
.M903 i Cam motor assembly X-3950-970-1
2-4
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
Drum assembly (M901) (DZH-0D1A-R) 1-796-012-11 (SLV-EX80SAR/EX90SAR) Drum assembly (M901) (DZH-0B4A-R) 1-772-363-11 (SLV-EX50BR) Drum assembly (M901) (DZH-0B7A-R) 1-772-366-11 (SLV-EX80SBR/EX90SBR)
QQ
QQ
Drum assembly Q (M901) (DZH-0D0A-R) TEL 13942296513 3 76315150 892498299 Q 1-796-011-11 (SLV-EX50AR)
13942296513
13942296513
Q002 Tape top sensor 8-729-043-84
TEL
TEL
Q001 Tape end sensor 8-729-043-84
http://www.xiaoyu163.com
QQ 376315150 892498299 2-7. CIRCUIT BOARDS LOCATION
(
MA-402 VIDEO, AUDIO, SERVO/SYSTEM CONTROL, TUNER, I/O, MODE CONTROL, POWER SUPPLY
) TEL
TEL
DI-81 (DIAL TIMER)
www
.
xiaoy u163. com 2-5E
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 376315150 892498299
QQ
QQ
TEL 13942296513 FJ-31 (LINE 2 IN)
13942296513
13942296513
DM-98 (USER CONTROL)
http://www.xiaoyu163.com
SECTION 3 BLOCK DIAGRAMS
QQ 3 7 6 3 1 5 1 5 0
SLV-EX50/EX80S/EX90S
8 9 2 4 9 8 2 9 9
3-1. OVERALL BLOCK DIAGRAM
TEL
TEL
13942296513
13942296513
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3 3-1
.
c o
8 9 2 4 9 8 2 9 9
m 3-2
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
SLV - EX50/EX80S/EX90S
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
3-2. VIDEO BLOCK DIAGRAM
IC201y; REC/PB
IC201uk PB
IC101ql REC/PB
IC201tk REC/PB
IC2914 REC
REC:512mVp-p (H) PB :584mVp-p (H)
320mVp-p (H)
2.1Vp-p (H)
IC291w; PB
IC2914 PB
152mVp-p (H)
2.2Vp-p (H)
2.36Vp-p (15.7KHz)
640mVp-p (H) IC201ug REC/PB
IC201ul PB
496mVp-p (4.43MHz)(PAL)
TEL
TEL
720mVp-p (H)
IC201ua REC/PB
13942296513
13942296513
608mVp-p (3.58MHz)(NTSC)
IC201iaREC/PB
5.3Vp-p (H)
3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
IC201t; REC/PB
IC101qj REC/PB
4.6Vp-p (H) 2.16Vp-p (15.7KHz)
IC201ih,il REC
40mVp-p (H)
IC201e;REC/PB
1.1Vp-p (H)
www
.
x ia o y u 1 6 3 IC201qk,ql REC/PB
IC201wa REC/PB
REC:472mVp-p (H) PB :504mVp-p (H)
392mVp-p (H)
REC:472mVp-p (H) PB :504mVp-p (H)
3-3
c o
IC201whREC/PB
IC201wd REC/PB
.
REC:512mVp-p (H) PB :584mVp-p (H)
3-4
http://www.xiaoyu163.com
m
376315150 892498299
376315150 892498299
QQ
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0 3-3. SERVO/SYSTEM CONTROL BLOCK DIAGRAM
SLV-EX50/EX80S/EX90S
8 9 2 4 9 8 2 9 9
IC101
EDIT PB/XREC —> PB/REC • : non flammable resistor • : fusible resistor • : panel designation • : internal component. • B+ : B+ Line. • B– : B– Line. • Circled numbers refer to waveforms. • Readings are taken with a color-bar signal input. • Voltage are dc between ground and measurement points. • Readings are taken with a digital multimeter (DC10MΩ). • Voltage variations may be noted due to normal production tolerances. • : adjustment for repair. • Circled numbers refer to waveforms. When indicating parts by reference number, please include the board name.
www
xiaoy u163. com
Note : The components identified by or dotted line with mark mark are critical for safety. Replace only with part number specified.
.
4-1
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
Kinds of capacitor
QQ
QQ
TEL 13942296513
13942296513
13942296513
(For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µµF. 50V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10W unless otherwise noted. kΩ=1000Ω, MΩ=1000kΩ. • Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. • Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520
TEL
TEL
B
6 5 4
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0 4-1. FRAME SCHEMATIC DIAGRAM
1
2
3
4
5
6
SLV - EX50/EX80S/EX90S
8 9 2 4 9 8 2 9 9
7
8
9
10
11
QQ
3 7 6 3 1 5 1 5 0
12
13
14
A
B
TEL
TEL
C
13942296513
13942296513
D
1 3 9 4 2 2 9 6 5 1 3
8 9 2 4 9 8 2 9 9
F
G
376315150 892498299
376315150 892498299
TEL
QQ
QQ
E
H
I
J
www
.
x ia o y u 1 6 3 4-3
.
c o
m 4-4
http://www.xiaoyu163.com
FRAME SCHEMATIC DIAGRAM
http://www.xiaoyu163.com
SLV - EX50/EX80S/EX90S
QQ 3 7 6 3 1 5 1 5 0
4-2. PRINTED WIRING2 BOARDS AND 1 3 SCHEMATIC 4 DIAGRAMS5
6
7
8
8 9 2 4 9 8 2 9 9
9
10
MA-402 (VIDEO, AUDIO, I/O, SERVO/SYSTEM CONTROL, TUNER, MODE CONTROL, POWER SUPPLY) PRINTED WIRING BOARD — Ref. No. MA-402 Board:1,000 Series —
12
13
14
There are few cases that the part printed on this diagram isn’t mounted in this model.
MA-402 Board
A
1
B
11
2
3
4
5
6
7
8
9
10
11
12
13
A
TEL
TEL
B
C
13942296513
13942296513
C
D
1 3 9 4 2 2 9 6 5 1 3
QQ
3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
F F
G G
H H
I
J
I
www J
.
x ia o y u 1 6 3
VIDEO, AUDIO, SERVO/SYSTEM CONTROL, TUNER, POWER
.
c o 4-6
MA-402
http://www.xiaoyu163.com
m
376315150 892498299
376315150 892498299
T EE L
QQ
QQ
E
D
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0 1
2
3
4
5
6
B
8
G
IC601 IC660 IC600 IC031
G1 H1 D2 I4
Q001 Q380 Q378 Q172 Q171 Q373 Q372 Q381 Q374 Q377 Q376 Q901 Q174 Q175 Q151 Q003 Q203 Q204 Q375 Q302 Q303 Q301 Q205 Q192 Q191 Q211 Q206 Q210 Q153 Q201 Q202 Q710 Q701 Q706 Q709 Q708 Q701 Q703 Q704
F3 C5 C5 G5 H5 B6 B6 B6 B6 C6 C6 D6 G6 G6 H7 F7 D7 D7 C7 A7 A8 A8 F8 G8 G8 D8 B9 E10 I10 C10 D11 E11 D12 D12 E12 E12 B13 F13 G13
TEL
QQ
3 7 6 3 1 5 1 5 0
12
1 3 9 4 2 2 9 6 5 1 3
(
MA-402 VIDEO, AUDIO, SERVO/SYSTEM CONTROL, TUNER, I/O, MODE CONTROL, POWER SUPPLY
8 9 2 4 9 8 2 9 9
)
H
I
DM-98 (USER CONTROL) FJ-31 (LINE 2 IN)
J
www
13
14
x ia o y u 1 6 3 DI-81 (DIAL TIMER)
.
4-7
.
c o
m 4-8
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
F
C1 D1 F1 F1 I2 I2 F2 F2 F2 E2 E2 D2 D2 C2 C2 C2 C3 E3 H3 J3 A4 C4 H4 G5 G5 A6 F7 H8 J10 H10 H11 B11 C12
J5 I5 D6 I7 H8 C9 A10 I12 C12 H13
11
QQ
QQ
E
D623 D625 D613 D612 D403 D614 D608 D609 D611 D601 D604 D603 D607 D605 D624 D600 D602 D626 D103 D404 D901 D071 D101 D171 D172 D902 D001 D100 D401 D151 D102 D201 D701
IC502 IC141 IC291 IC451 IC101 IC201 IC301 IC142 IC662 IC702
10
13942296513
13942296513
D
A1 J1 J2 A3 B4 E4 A6 H6 B10 B10 I12 I12 D12 B12 J13 J13
9
TEL
TEL
C
CN600 CN412 CN411 CN072 CN071 CN051 CN331 CN031 CN201 CN204 CN104 CN105 CN332 CN202 CN334 CN413
8 9 2 4 9 8 2 9 9
7
MA-402 BOARD
A
SLV - EX50/EX80S/EX90S
http://www.xiaoyu163.com
MA-402 (VIDEO, AUDIO) SCHEMATIC DIAGRAM – Ref. No: MA-402 Board; 1000 series – • See page 4-5 for printed wiring board.
8
8 9 2 4 9 8 2 9 9
9
10
V51
51
SQ IN
Y OUT
0.3
1.5M
50
AV TAB
49
9
AUDIO ALC FILTER
AV TAB
48
AV TAB
Q206 UN2213-TX
VV46
2
2.5
S/VHS
CCD Y-OUT
CCD C-OUT AV TAB
C249 0.01u B
4.9
AUDIO LINE OUT
VCC
MAIN EM OUT(REC) MAIN DEEM IN(PB)
MAIN EM IN(REC) MAIN DEEM OUT(PB)
S-DET
E-PEAK
G-EQ
CLAMP DRIVE
MAIN CLAMP IN
ME FBC(REC) APL(PB)
Y-CCD DRIVE
ME ALC/PB FM AGC
Y-CCD CLMAP
Y-CCD LPF OUT
CCD ADJ
FROM Y-CCD
GND
LINE IN3
AGC DET
LINE IN2
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
B+
4.9
UN2213-TX Q203
UN2213-TX Q204 5
HA22
Q203,Q204 PAL/NTSC SWITCH
POWER
C250 47u 16V
ARGENTINA ONLY
C252 330p
A4
C253 1u B
R216 100
8
8 9 2 4 9 8 2 9 9
A ERASE HEAD
7
R11.8 P 0.3
1
NC
2
GND
3
2.8
R215 100
B+
AU_GND
5
L2_VIDEO
R 0.1 P11.9
11.9V
R381 XX
MA-402 (6/8) (SEE PAGE 4-23)
POWER EX50 * JS304 0.60mm
L2_AU_L NA11 NAOUT
JS302 0.60mm
BUFFER
C263 XX
ANGND
LINE1 EX80S/ EX90S
Q211 2SD601A-QRS-TX
R224 1k
MA-402 (8/8) (SEE PAGE 4-27)
DGND
VV26 1.6
UN2213-TX 0 Q210
4
GND ANGND SW12V
NA8
NAIN
D_GND JS379 TO HIFI BIAS_GND
HA22
HA22
NAOUT
HC36
AUDIO REC
MA-402 (4/8) (SEE PAGE 4-19)
AFENV
HC35 HC37
HA21
PS331
HC35
AUDIO CH2
HC37
AUDIO CH1
HA21
NAIN
GND
AU GND
7
BIASGND D_GND
R384 XX
MA-402 (7/8) (SEE PAGE 4-25)
B+
R11.4 P 0.3
C383 XX
R-0.4 P 0.3
1
BIAS ERASE OSC
R0.3 P 0.0
C376 1500p B
0.3
C377
3
5
BIAS ERASE OSC
R11.5 P 0.3
7 6
C384 XX
Q375 2SC4040-TL2-Q
T371 SB-D3244
C375 0.015u
Q381 XX
0.01u Y
R379 22k
R380 4.7
L372
2
x ia o y u 1 6 3 BIAS ERASE OSC
C378 47u 16V
C379 0.1u F
DGND
BIASGND
4-9
.
AUDIO SIGNAL
R370 47k
R 0.1 P11.9
L371 XX
c o R11.5 P 0.5
11.9 Q376 UN2115-QRS(TX)
SWITCH
4-10
http://www.xiaoyu163.com
VIDEO SIGNAL
CHROMA
100uH
8
SIGNAL PATH
UN2213-TX Q377
XX
R378 10k
BIASGND
1
B+
6
JS308 XX
C380 XX
R382 XX C382 XX
C373 220p PET
JS305
SW5V
SW5V
GND B
BRAZIL ONLY
R377
.
CTL+
TO POWER
B+
* R214 100
4
JL337
FE HEAD
CTL-
CN7
B+ C258 1u B
MA-402 (2/8) (SEE PAGE 4-13)
FULERA
CN6
XX JS378
3
RECP
B34
Q380 XX
DGND
JL334
AMUTE
B33
3
R383 XX
JL333
CN332 3P
FULL ERASE HEAD
JL341
2
R 0.3 P 0.0
CN6
B33
B34 Q374 UN2113-TX
CN7
NAPB
A99
EX50/EX80SAR/ EX90SAR
*C224 1u
C262 47p
REC TRAP SWITCH 5
1.9
2.8
2 C245 16V 10u
C243 50V 3.3u
1.4
2.1
3 L215 47uH
R223 220
5 6
MOD_AU
L205 10uH
TO IN/OUT
4.9
R219 2.2M R225 1k
LINE IN1
JL332
BIAS GND
MA-402 (5/8) (SEE PAGE 4-21)
AUDIO_RF_IN HA22
F C251
3 2.2u
B+
Q378 UN2213-TX
JS307 XX
XX
T372 XX
7
0.60mm
www AUDIO ERASE HEAD
REC A HEAD
2
VIDEO_RF_IN VV37 XX JS202
2.8
C248 2.2u 50V
2.3
R222 220
0.315A
L380
R 4.9 P 0.0
330 JL331
SCK
POWER VV26
A4 R376 10k
HEAD CONTROL SWITCH
4
SDA
6
L381 XX C381 XX
R-24.8 P 0.7
4.9
3
MESEC
HT43
*
0.1u F
0
R387 2200
Q373 2SD601A-QRS-TX
R-24.9 P 4.9
CTL GND
RFENV
AFENV
4
PB A HEAD
PB
HC36
R-20.6 P 0.0
R375 10k
AUDIO REC/PB HEAD
MA-402 (2/8) (SEE PAGE 4-13)
RFSWP
HT42
POWER
1.2
R367 XX
EX50
1.9
VV21 C233
C241 0.1u F
ARGENTINA ONLY
EX90SAR
C228 0.1u
R366 B 470
C238 16V 10u
C235 0.1u F C208 0.1u F
C232 15p R209 1k
0
R385 XX
2.3
R3.3/P0.6
R2.6/P3
R1.9/P1.3
L203 100uH JL207
C240 0.1u F
11
AV TAB
B+
C365
* C230 39p
R208 10k
C227 150p CH
R365 4700
HA21
R355 18k
Q372 2SD601A-QRS-TX
R372
PAL
V97
4.9
1
ACK
V82
AUGND
Q372,Q373 HEAD SWITCH
JL335
VDAT
VV21
A4
C363 22u 16V
0.01u R386 2200
R357 0
R226 120k R206 1500
C225 2.2u
V17
C359 R356 10u 27k 16V
1u 50V
V76
C356 1500p R354 33k B
EX50 C362 1u 50V
C361
BRAZIL ONLY
C360 XX
EX50BR/ EX80SBR/ EX90SAR *
C358 4.7u 50V
V16
B+
R353 100
C355 10u 16V
R205 6800
2.2
AUDIO BYPASS
4
3
AUDIO LINE IN1
3
2.7
AUDIO LINE IN2
2
2
AUDIO LINE IN3
1
R1.9/P1.3
B.G.
R352 150k
10
AUDIO GND
AUDIO PB EQ OUT
R359 XX
2
1k
VCLK
V84
2
3 7 6 3 1 5 1 5 0 AV TAB
AUDIO REC OUT
MUTE
12
13
12
R361 47k
Y CTL (Y)
8200 R289
4.9 CCD TAB
QQ
REC Y+C OUT
R 2.6/ P2.4
R0/P1.7
R299
* C295 B 0.01u
CL294
VV35
C354 22u 16V
CTL HEAD
VOUT
V81
4.9
XX
R371 330
QVD
V52
V76
VV44
3
CCD VCC
L214 10uH
CL303
4.9
APC
V64
0.1
2.4
0.1u F C353 16V XX R350 10k
CL296
CSYNC
VR63
0.1
INVERTER
CL297
2.5
V51
VR62
45 42 41 40
CCD TAB
CCD MODE COUNT IN
AUDIO VCC
CL298
2.7
NTSC
V17
39
SP CH1(+)
1.8
* C294 0.01u B *
7 8 V16
V50
47
8
VIDEO REC/PB AMP VIDEO INPUT SELECT Y/C PROCESS NORMAL AUDIO PROCESS
JS204
C371 0.001u B
DATA
CL299
EX90S
35
C351
R351 3300
JL336
MAIN OFF
10u 16V
1.9
V50 JL236
4.9
JS203
1
SUB CLK
4.1
0.4 SYMC SEP OUT
46
COLOR IN
VIDEO OUT FBC
PB C-OUT
VIDEO OUT ALC
CCD CONT
C-CCD FB-IN
LEVEL DET
C-CCD DRIVE
VCC
IIC CLK
IIC DATA
KILLER OUT
2fsc VCO DET
LC-VCP
DO OUT
GND CCD SIG 2fsc OUT
4.6
B+
C350 16V 10u R368
2.5
X CTL (X)
SUB MONI 2
4.6
4.7u 50V
B+
38
SP CH1(-)
R0.1/P2.2
L351
JS306 0.60mm
SP CH2(-)
1 3 9 4 2 2 9 6 5 1 3
CN331 7P
SUB MONI 1
9
52
37
R0.1/P2.2
C352 0.022u B
I
SUB FIL ADJ
15 16
*C298 * C296
*
1
*
* 53
11 12 13 14 15 16 17 18 19 20
JL208
0.1
2.4
2.8
1.9
2.3
0.1
3
3.1
2.1
4.7
4.7
4.7
0
R1/ P2.6
4.7
4.7
2.8
2.8 CR-DET
3.58 X’tal IN
ACC DET
X’tal OSD OUT
REC APC
PB APC/REC APC
2
*
3900
EX50/ EX80SAR JL209
JL235
VV37
* R212
EX90S
* R211 0
VV35 JL211
C236 0.1u
JL213
JL214
JL210
JL212
VV46
VR62
V64 C231 0.022u JL215
L204 12uH
JL216
GND
X202 3579.545kHz
ARGENTINA ONLY
2.1
1.8
2.3
2.1
R2.7 /P1
2.4
2.1
54
34
* C212 22p * C213 22p
0.1
H
MA-402 (1/8)
55
IC201
B+
VIDEO, AUDIO
VR63
VV44 C222 0.1u
C220 0.47u C221 0.022u X201 3582.056kHz
EX50AR/ EX80S/EX90S C217 4700p
C216 1u
R228 470
0.01u
C215
SEP C IN
PB C OUT
SP/EP
MESECAM DET
81
3.58/4.43 X’tal IN
7
SP CH2(+)
G
J
56
36
R0.1/P2.2
A99
F
57
AUDIO PB EP SW
6
58
AUDIO PB IN (+)
SP CH1
59
CCD TAB
0
5
60
VCC
ARGENTINA ONLY
TEL
4
61
CL230
2.3
m Ref.signal
Y
Y/CHROMA
REC PB
REC
REC/PB
PB
376315150 892498299
376315150 892498299
SP CH1
SP CH2 SP COM
62
R0.1/P2.2
2.5
SP CH2
L207 10uH
XX
4.9
63
IC201 HA118217F
4.9
GND V97
64
CCD Y-IN
C357 1500p
3
65
AUDIO PB IN (-)
2
LP CH1
66
SP CH1(+)
2.5
LP COM
67
CCD TAB
JL220
BRAZIL ONLY R218 4700
1
4.9
98
E
LP CH2
68
2.5
QQ
QQ
LP CH1
SP CH1(-)
R364 0
C257 4700p
* CN204 6P
69
C364 50V 4.7u
JL303
EX50
LP CH2
C201 2.2u F
C254 4700p C255 2200p C256 2200p
JL292
R294 100 R295 100
HT43
CCD CLK IN
2.5
HC35
70
2.4
1
JL304
GND VCC
1.1
0.2
2
R362
AUDIO CH2
2
HC36
REG Y OUT
4.9 CL295
JL291
2.4 XX JS205
JL305
2.2u
R291 10k
CCD GND
15k
AUDIO COM AUDIO CH2
2.4
JL225
HC37
Y IN Y SYNC
1.8
CL293
* C292
MCOR 3 YOUT
2.3
0.22u
V52
C247 0.22u
6
R363 47k
3
C246 0.01u
C IN C OUT
2.9
CL292
0.2
71
5
2.5
4
AUDIO CH1
4
CL290
0.1u
* C291
2.6
* R296 8200 *C299 0.01u B CL231
LA7277M-TLM
CL291
4.7u
* C290 50V * C289
CCD C-IN
SP CH2(-)
99
AUDIO CH1
BRAZIL ONLY
* C211 22p
C205 4700p
5
FE
2.5
91
FE
SP CH2(+)
100
SP CH1
C242 0.1u F
* IC291
EX90S
44
* C210 22p
C204 2200p
JL205
C239 0.01u
EX50/EX80S JS291 0
43
C203 2200p
JL206
72
JS360 0
6
73
R360 15k
7
74
2.5
8
SP CH1
75
EX80S/ EX90S
JL203
GND
89
SP CH2 SP COM
76
EX90S
2.4
JL204
SP CH2
77
2.8
9
85
LP CH1
C202 4700p
JL202
86
10
ENV OUT
87
B+
R0/P3.8 C207 0.01u
88
11
JS208
R207 4700
C237 0.01u B
C234 16V 47u
14
IC291
B+
13942296513
13942296513
LP CH2 LP COM
C259 150p
C218 2.2u 50V
3.3u 50V
JL201
LP CH1
3
CK DET DISCRI
90
LP CH2
CN201 11P
R204 27k
C229 4.7u 50V
C226 6p CH
15 17
14
TEL
TEL
EX80S/EX90S
2.4
82
1.3
83
C206 0.033u
DRUM FF IN
84
JL224
C209
*
0
D201
1SS119-25TD
1 2.2
92
4
C244 0.01u B
93
GND
JL222 JL223
94
3
AFENV
95
V.SWP
JL221
78
L206 10uH
C223 4.7u 50V
0
79
AV-SS
13
12
HT42
96
2
80
97
1
PB RF
R3.6/P2.1
BUFFER
CL203
JL217
HF ADJ
4.9
1.8M
* R292
CHECK (JIG)
JL238
Q201 2SB709A-QRS-TX
JS201
CN202 4P
BRAZIL ONLY
R202 470
R3.6/ P2.1
JL237 Q205 UN2213-TX
L211 220uH
L202 10uH
R4/P1.5
4.5
R201 1k
BRAZIL ONLY
C264 150p
C214 27p
2.7
JL234
* R203 100
0
EX50BR/ EX80SBR/EX90SBR
0.001u C219
B
D
V76
Q202 XX
BRAZIL ONLY
C
V84
V82
5
B+
A
V81
MA-402 BOARD(1/8) XX MARK:NO MOUNT NO MARK:REC/PB MODE R :REC MODE P :PB MODE
11
3
7
4
6
10
5
*
4
33
3
32
2
31
1
5
QQ 3 7 6 3 1 5 1 5 0
6
SLV - EX50/EX80S/EX90S
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0 1 2 MA-402 BOARD (1/8)
3
4
5
6
7
SLV - EX50/EX80S/EX90S
8 9 2 4 9 8 2 9 9
8
9
(VIDEO, AUDIO BLOCK)
A
6 IC201 ua REC/PB
1 IC201 ia REC/PB
10
11
12
13
14
qh IC291 qk PB
qa IC201 wh REC/PB
B
608 mVp-p (3.58 MHz) (NTSC)
5.3 Vp-p (H)
7 IC201 y; REC/PB
2 IC201 ih, il REC
qj IC291 4 PB
TEL
TEL
C
1.9 Vp-p (H)
REC: 512 mVp-p (H) PB : 584 mVp-p (H) qs IC201 qk, ql, wd REC/PB
13942296513
13942296513
D 320 mVp-p (H)
40 mVp-p (H)
8 IC201 tk REC/PB
QQ
1 3 9 4 2 2 9 6 5 1 3
3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
F REC: 512 mVp-p (H) PB : 584 mVp-p (H) 9 IC201 t; REC/PB
720 mVp-p (H) 4 IC201 uk PB
392 mVp-p (H) qf IC291 w; PB
G
H 4.6 Vp-p (H)
640 mVp-p (H)
q; IC201 e; REC/PB
5 IC201 ug REC/PB
152 mVp-p (H) qg IC291 4, qk REC
I
J
www 496 mVp-p (4.43 MHz) (PAL)
.
x ia o y u 1 6 3 1.1 Vp-p (H)
2.1 Vp-p (H)
4-11
.
c o
m 4-12
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL
QQ
QQ
3 IC201 ul PB
E
2.2 Vp-p (H)
REC: 472 mVp-p (H) PB : 504 mVp-p (H) qd IC201 wa REC/PB
http://www.xiaoyu163.com
SLV - EX50/EX80S/EX90S MA-402 (SYSTEM CONTROL) SCHEMATIC DIAGRAM – Ref. No: MA-402 Board; 1000 series – • See page 4-5 for printed wiring board.
QQ 3 7 6 3 1 5 1 5 0 2
3
4
5
6
7
8
8 9 2 4 9 8 2 9 9
9
10
MA-402 BOARD(2/8)
HT62
HT61
V60
V59
0
0
1k
1k
R167
R163
T66
T68
V67
V70
T69
A71
A72
HT74 C114 47u 25V
13
12
R159
S43 FL58
FL63
10k
47k R120
47k R119
47k R118
10k
R158
R128
R127
R162
10k
10k
FL65
FL64
JL117
R132 10k
DRUM_PG
CAP_QR
R156 33k
Vcc
C103 0.22
Vss
FLD CS
SCL0
SDA0
SCL1
sO1
SCK1
SI1
TA MUTE\OSD MIX
F.MONO\PAL
MAIN\SAP\SW2
STEREO OUT\SW1
SDA1
PB
V50
M33
2.6
R115 470
5.2
M45
JL121
C107 3300p
R121 1k
5.1 0.1-5
M42
0.1-5
M41
0
M40
0
M39
4.7
M38 M37
4.7 5.4
C105
R130
3.1
0.1u
R129 100k
V34
C113 B 0.1u
2.5 2.5
EX90SAR * R101 22k
EX50AR/ EX80SAR/ * R102 10k EX90S R103 10k
3.7 2.7
8 9 2 4 9 8 2 9 9
H35
1k
0
M33 M33
V30
5.2
JS103 XX
CN105 5P
HT61
JL131
1
GND
2
DATA
3
CLK
4
RESET
5
WRITE CONT
1
MD0
2
SO1
3
SI1
4
RESET
JL132 JL134 JL133
R131 10k
K1 JS151 0 R126 1k
C159 XX
FL65
DGND
JL135
X152 XX
Q152 XX
JL136
R133 1M
C161 12p
HT74
JL137
C166 XX
C162 7p CH
B+
5
GND
6
FLASH WRITE ENABLE
7
VCC
X151 14.328224MHz ARGENTINA ONLY
C106 0.01u B
DGND
CN104 XX
HT82 FL64
Q151 XX
R110 10k
T_SENS
JL129
2.3
5.3
5.3
5.3
4.6
0.2
2.4
S_SENS
JL122
R105 10k
R152 100 C164 0.01u B
2.5
2.1
4.9 R151 470k
0.2
1.7
2.6 10k
100k
END_LED
JL126
R155 1M
R154
R193
S_REEL
M49
HT62
50V
DGND GND
B+
SYSCON
D_5.2V
14 MA-402 (3/8) (SEE PAGE 4-17)
B+
HT62
HT61
HT51
2
3
4
D103
DGND
MPG06D-6052PKG3
5.0 DATA
5.0 CLK
5.2 WRITE CONT
5.2 VCC
5.2 VCC 2
4.1
5.4
1
SIGNAL PATH
REC DRUM SPEED SERVO DRUM PHASE SERVO
1
2
3
NC
4700 R177
NC
Q174 UN2211-TX
C172 56p CH GND
DRUM SERVO(SPEED AND PHASE)
4
m
CAPSTAN SPEED SERVO
IC141
x ia o y u 1 6 3 UN5V
B+
.
5.3 OUT 1
L172 22uH
R175 470
2.5
BLUE BACK SWITCH DGND
5
XX Q173
S28
OSD
6
NC
GND
INVERTER
7
IC142 M24C08-WMN6T(A)
C171 0.1u F
8
NC
Q171 UN2211-TX
R173 XX
5
NC
VIDEO BUFFER
V67
Q175 XX
OSD MIX
C143 0.1u B
6
NC
0
0.4
C142 0.01u B
7
VCC 1
C141 0.01u B
R178 XX R176 XX
SW5V
PB B+
OUT 2
XX D172
D403
MPG06D-6052PKG3
VIDEO SIGNAL
T25
V24
V111 1.7 1.2
GND
R172 100
V17
POWER
www
XX D171
8
5.1
I
R174 680
15 MA-402 (8/8) (SEE PAGE 4-27)
UN5VBCAP
IC141 MM1256AFBE
OUT
5.2 C456 0.01u B
R171 1k V18A
1/4W 47k R526
PCO
JS101 R143 470k
S27
C455 100u 10V
R142 220k
C173 XX
L171 22uH
2SB709A-QRS-TX
GND
1
R144 220k
T66 L151 22uH
VCC
2
4.8
3
XX
RESET
NC
IC502 SFH5110-40 JL503
JL501
B+
GND D_GND
Y/CHROMA JL127
B+
UN5VBCAP
Q172
POWER_FAIL GND
C4
C3
CN2
R104 100
MA-402 (2/8)
SAP\BILL OUT\SECAM ON
REC P
22p C154 4.7u 50V C100
C152 4.7u
1500p
B+
L174
SYSTEM CONTROL
M32
B+
S27
UN5V
J
D100 1SS119-25TD
C163 7p
S28
MA-402 (7/8) (SEE PAGE 4-25)
JL119
5.2
HT51
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
4700
9
C192
14
S54 S55
POWER
12
FULL ERASE
IN SELEC
Flash Write Enable
32kHz X’tal
32kHz X’tal
RESET
10MHz X’tal
8
C193 0.1u JL192
DGND
D_GND
H
5.2
M49
FL65
ETR2
FUNC_KEY_2
R123 10k
T_REEL
M41
5.2
FL64
ETR1
FUNC_KEY_1
5
V19
SI1
DEST2
JS171 0.60mm
SO1
FL63
S SENS
M9
MA-402 (7/8) (SEE PAGE 4-25)
Q192 XX
UN5VBCAP
11
JS191
C195 22u 16V
FL58
7
C196 1500p
G SCK1
6
C194 47u 16V
C191 XX R191 XX Q191 XX C197 XX
FLD_CS
Vss
5
1.9
4
L173 15uH 2.1 R100 33k 1.7
2.5 *
C53
3
C151 C155 0.01u
C3
2
2.2u F
CTL+
T SENS
DEST1
R153
1
UN5VBCAP
C4
4
3
C53
HT51
C104 470u 10V CTL-
10MHz X’tal
13 1 2
CSync
C102 XX
A71
Cap Connect to Vss
Vss
A72
FULERA
MDO
QVD
VIDEO RF
MODE1
M42 S54
3 7 6 3 1 5 1 5 0 AUDIO RF
MODE2
M37 S55
5.0
DGND
D151 1SS119-25TD
QQ
CAP PWM
C160 0.01u
MA-402 (1/8) (SEE PAGE 4-9)
F
RECP
1.8 5.2
C101 0.1u F
A89
DRUM PWM
SVSS
3
V111
A96
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56
ARGENTINA ONLY NAPB AMUTE
0.1
AF SWP
AVcc
Func. Key 1
C165 22p
2.7
5.0
POWER FAIL
C072 0.22u B
H35
2.7
MODE 1
Func. Key 2
HT61
RF SWP
MODE 2
4.9
AFENV
HT62
9 10 11 12
DRUM PG DRUM FG
1 3 9 4 2 2 9 6 5 1 3 3
MODE 4 MODE 3
R160 1.9 470
376315150 892498299
SCK
2.8
HEAD CLOG LED
4.4
SDA
H106
V97
S REEL
MESECAM DET
2.4
MA-402 (4/8) (SEE PAGE 4-19)
5.1
R107 1k V105 R106 0.60mm H106 R108 M107 10k R111 M108 22k R109 1k C053 0.068u V109
T REEL
SERVO/SYSTEM CONTROL OSD
M38
IC142
POWER FAIL DET RESET PULSE GENERATOR
4-13
EEP ROM
.
c o
CAPSTAN SERVO (SPEED AND PHASE) REF. SIGNAL
4-14
http://www.xiaoyu163.com
REC/PB
PB
376315150 892498299
TEL
AFSWP AF_REC_P
M104
C.KILLER DET
2.6
10
R117 1k 0.1
IC101
SECAM DET
5.2
QQ
QQ
E
B+
JL113
M103
REMOTE CON
TU AFT
V102
UN5V
JL110 R451 4.1 470 JL452
HD642917Y
APC Error
V19
OSD CTL
AF REC P
AVSS
V100
OSD
CAM
IC101
4fsc in
9 MA-402 (6/8) (SEE PAGE 4-23)
SAT. SYNC. LED
NA PB
4fsc out
JL123
RR LED
PLL DATA
OSDVss
0
JL100
V97
TU ENABLE
CVout
R5/P0
OSDVcc
4.8
JL116
CVin1
A96
CVin2
T95
VLPF/Vsync
T94
HT43
Csync/Hsync
V50 HT42
SEARCH LED
PLL CLOCK
10k
SCK
0.5
END LED
R194 10k
SDA
0.2
R113 470 R112 470
Drum QR
AFC LPF
T93
POWER
PCO
2.6 R114 470
AFCosc
M92
AUDIO DUB
POWER CONT
AFCpc
V102
ETR 1
CAP QR
SVCC
2.7
MODE3
ETR 2
WRITE CONT
CAP FG
M91
MODE4
Vcc
6
CTL SMT
V34
REC_PROOF M39
CAP RVS
CTL AMP(0)
4.4
CTL FB
POWER
M90
CAP_TRQ_PWM M86
BLUE BACK
2.5
MESEC
V105
M85
M40
A Mute
2.5
RFENV
JL120
7
CTL(-)
A89
0
CTL BIAS
JL130
V67
RFSWP
D
V100
R192
JS102 0.60mm
8
REC PROOF
CTL REF
PAL
V60
JL128
47k R125
JS104 XX
CAP TRQ PWM
CAP_PWM
13942296513
13942296513
ACK
5.0
M86
V59
VDAT
3.8
CTL(+)
VCLK
MA-402 (1/8) (SEE PAGE 4-9)
R057 10k
M85
2.5
V17
TV / VTR
VOUT
APC PWM
V109
2.5
QVD
112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85
V84 V111
MA-402 (3/8) (SEE PAGE 4-17)
M108
C169 0.1u F
TEL
TEL
1
V18A
APC
13
CAP_FG M91
84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 NTSC
DRUM_FG
M90
3.9
5.1
5.1
5.0
5.0
4.6
0.4
5.2
0
5.1
0
0
JL138
X102 32.768kHz
JL125
JL118
CH
C111 20p CH
CH
20p
0.22u C110
DRUM_QR M103
2SD601A-QRS-TX
CSYNC
DRUM_PWM
M104
CAP_RVS
5
Q153
CAM M107 M92
M9
R0.1/ P11.8
5.4
1.5
HT57
1.9
7.0
JL124
2.4
2.1
HT56
4700 R161
C109 15p 4.8 JL115 C112 B
SDA
10k
V84
C108
V30
SCK
C
14
M45
R124 10k
V70
PB
R165
C167 0.22u
C168 0.1u
R164 1k
10k
SAP_BILL_OUT/SECON
V24
JL139
T66
JL140
TUNER_MUTE
3.3
V67
R157
T69
F.MONO
2.6
T83
SW1/STEREO_OUT
5.1
MA-402 (5/8) (SEE PAGE 4-21)
15p CH
T68
TV/VTR
X101 10MHz
T25
SW2/MAIN/SAP
R122 1M
T94
AFT
2.5
T95
ENABLE
0
8
11
T93
PLLDAT
2.7
B
R166
PLLCLK
HT82
T83
A
XX MARK:NO MOUNT NO MARK:REC/PB MODE R :REC MODE P :PB MODE
47k R116
1
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0 1MA-402 BOARD 2 (2/8)
3
4
5
6
7
SLV - EX50/EX80S/EX90S
8 9 2 4 9 8 2 9 9
8
9
(SYSTEM CONTROL)
1 IC101 3 REC
6 IC101 ug REC/PB
qa IC101
CN901 1-695-368-31 CN901 1-784-449-11
CONNECTOR, FFC/FPC 7P CONNECTOR, FFC/FPC 7P
S462 S463 S466 S467 S468
1-762-196-21 1-762-196-21 1-762-196-21 1-762-196-21 1-762-196-21
SWITCH, SWITCH, SWITCH, SWITCH, SWITCH,
TACT TACT TACT TACT TACT
(AEJECT) (zREC) (mREW) (xSTOP) (HPLAY)
S469 S472
1-762-196-21 1-762-196-21
SWITCH, TACT SWITCH, TACT
(MFF) (XPAUSE)
D900
8-719-056-06
DIODE SLR-342DCT31
1-216-295-00 1-216-043-91
SHORT RES-CHIP
0 560
5%
1/10W
* * *
S900 S901
1-762-196-21 1-418-059-22
QQ 376315150 892498299 A-6713-949-A A-6713-947-A A-6713-941-A
FJ-031 BOARD COMPLETE (SLV-EX50) FJ-031 BOARD COMPLETE (SLV-EX80S) FJ-031 BOARD COMPLETE (SLV-EX90S) ********************
SWITCH, TACT (SEARCH) ENCODER, ROTARY (CAM ENCODER) CN532 1-695-368-31 CN532 1-784-449-11
*
A-6713-942-A
DM-098 BOARD COMPLETE **********************
CNJ531 1-770-021-11
CN471 1-770-514-31 CN471 1-784-447-11
JR461 1-216-295-00
CONNECTOR, FFC/FPC 7P CONNECTOR, FFC/FPC 7P
JACK, PIN 3P
(SLV-EX80S/EX90S)
CONNECTOR, FFC/FPC 5P CONNECTOR, FFC/FPC 5P
D531
8-719-071-15
D532
8-719-071-15
D533
8-719-071-15
SHORT
D534
8-719-017-09
0
DIODE HZM6.8ZWA1TL (SLV-EX80S/EX90S) DIODE HZM6.8ZWA1TL (SLV-EX80S/EX90S) DIODE HZM6.8ZWA1TL (SLV-EX80S/EX90S) DIODE 02DZ6.2-TPH3 (SLV-EX80S/EX90S)
xiaoy u163. com
www
R465 R467 R468 R469 R470
1-216-053-00 1-216-057-00 1-216-053-00 1-216-053-00 1-216-057-00
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
.
1.5K 2.2K 1.5K 1.5K 2.2K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
JS531 JS532 JS534 JS535
1-216-296-00 1-216-296-00 1-216-295-00 1-216-295-00
8-6
http://www.xiaoyu163.com
SHORT SHORT SHORT SHORT
0 0 0 0
(SLV-EX80S/EX90S) (SLV-EX80S/EX90S) (SLV-EX80S/EX90S) (SLV-EX80S)
376315150 892498299
376315150 892498299
TEL 13942296513
R900 R902
QQ
QQ
13942296513
13942296513
http://www.xiaoyu163.com
SLV-LX80S
QQ 376315150 892498299 FJ-31
Ref. No.
Part No.
Description
Remarks
R533
1-216-021-00 RES-CHIP
R534
1-216-097-11 RES-CHIP
R535
1-216-097-11 RES-CHIP
68
5% 1/10W (SLV-EX80S/EX90S) 100K 5% 1/10W (SLV-EX80S/EX90S) 100K 5% 1/10W (SLV-EX80S/EX90S)
*
A-6713-945-A MA-402 BOARD COMPLETE
*
A-6713-948-A MA-402 BOARD COMPLETE
(SLV-EX50AR)
* * *
A-6713-940-A MA-402 BOARD COMPLETE (SLV-EX90SBR) *********************
CHIP CHIP CHIP CHIP CHIP
15PF 20PF 20PF 0.22UF 0.1UF
5.00% 5.00% 5.00% 10.00% 10.00%
50V 50V 50V 16V 25V
C114 C141 C142 C143 C151
1-126-947-11 1-164-232-11 1-164-232-11 1-164-004-11 1-164-505-11
ELECT CERAMIC CERAMIC CERAMIC CERAMIC
CHIP CHIP CHIP CHIP
47UF 0.01UF 0.01UF 0.1UF 2.2UF
20.00% 10.00% 10.00% 10.00%
25V 50V 50V 25V 16V
C152 C154 C155 C160 C161
1-126-163-11 1-126-163-11 1-164-232-11 1-164-232-11 1-163-096-00
ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
4.7UF 4.7UF 0.01UF 0.01UF 13PF
20.00% 20.00% 10.00% 10.00% 5.00%
50V 50V 50V 50V 50V
C162 C163 C164 C165
1-163-096-00 1-163-229-11 1-164-232-11 1-163-235-11
CERAMIC CERAMIC CERAMIC CERAMIC
1-164-489-11 1-164-004-11 1-163-038-00 1-163-038-00 1-163-245-11
CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC
C165
C167 C168 C169 C171 C172
C001 C002 C003 C004 C005
1-163-009-11 1-163-009-11 1-163-009-11 1-163-009-11 1-128-057-11
CERAMIC CERAMIC CERAMIC CERAMIC ELECT
CHIP CHIP CHIP CHIP
0.001UF 0.001UF 0.001UF 0.001UF 330UF
10.00% 10.00% 10.00% 10.00% 20.00%
50V 50V 50V 50V 6.3V
C031 C032 C034 C051 C053
1-128-499-11 1-164-232-11 1-164-232-11 1-124-589-11 1-164-344-11
ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
220UF 0.01UF 0.01UF 47UF 0.068UF
20.00% 10.00% 10.00% 20.00% 10.00%
16V 50V 50V 16V 25V
C054 C071 C072 C073 C074
1-163-038-00 1-163-809-11 1-164-489-11 1-164-232-11 1-163-009-11
CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC
0.1UF 0.047UF 0.22UF 0.01UF 0.001UF
10.00% 10.00% 10.00% 10.00%
25V 25V 16V 50V 50V
C075 C076 C100 C101 C103
1-163-259-91 1-126-941-11 1-163-235-11 1-163-038-00 1-104-905-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CAPACITOR
220PF 470UF 22PF 0.1UF 0.22F
5.00% 50V 20.00% 25V 5.00% 50V 25V 5.5V
10.00% 16V 10.00% 25V 25V 25V 5.00% 50V
C104 C105 C106 C107 C108
1-126-935-11 1-164-004-11 1-164-232-11 1-164-182-11 1-163-231-11
ELECT CERAMIC CERAMIC CERAMIC CERAMIC
470UF 0.1UF 0.01UF 0.0033UF 15PF
20.00% 10.00% 10.00% 10.00% 5.00%
1-163-145-00 1-164-004-11 1-124-589-11 1-124-234-00 1-163-145-00
CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP
0.0015UF 0.1UF 47UF 22UF 0.0015UF
5.00% 10.00% 20.00% 20.00% 5.00%
50V 25V 16V 16V 50V
C201 C202 C203 C204 C205
1-164-505-11 1-163-017-00 1-164-161-11 1-164-161-11 1-163-017-00
CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC
CHIP CHIP CHIP CHIP CHIP
2.2UF 0.0047UF 0.0022UF 0.0022UF 0.0047UF
10.00% 10.00% 10.00% 10.00%
16V 50V 50V 50V 50V
C206 C207 C208 C209 C210
1-163-989-11 1-164-232-11 1-163-038-00 1-126-162-11 1-163-235-11
CERAMIC CERAMIC CERAMIC ELECT CERAMIC
CHIP CHIP CHIP
C211
1-163-235-11 CERAMIC CHIP 22PF 5.00% 50V (SLV-EX50BR/EX80SBR/EX90SBR) 1-163-235-11 CERAMIC CHIP 22PF 5.00% 50V (SLV-EX50BR/EX80SBR/EX90SBR) 1-163-235-11 CERAMIC CHIP 22PF 5.00% 50V (SLV-EX50BR/EX80SBR/EX90SBR) 1-163-239-11 CERAMIC CHIP 33PF 5.00% 50V (SLV-EX50AR/EX80SAR/EX90SAR) 1-163-237-11 CERAMIC CHIP 27PF 5.00% 50V (SLV-EX50BR/EX80SBR/EX90SBR)
C213 C214 C214
C215 C216 C217 C218
1-164-232-11 1-109-982-11 1-163-017-00 1-124-257-00
0.033UF 10.00% 25V 0.01UF 10.00% 50V 0.1UF 25V 3.3UF 20.00% 50V CHIP 22PF 5.00% 50V (SLV-EX50BR/EX80SBR/EX90SBR)
CERAMIC CHIP 0.01UF 10.00% 50V CERAMIC CHIP 1UF 10.00% 10V CERAMIC CHIP 0.0047UF 10.00% 50V ELECT 2.2UF 20.00% 50V (SLV-EX50AR/EX80SAR/EX90SAR) 1-126-163-11 ELECT 4.7UF 20.00% 50V (SLV-EX50BR/EX80SBR/EX90SBR)
xiaoy u163. com CHIP CHIP CHIP CHIP
0.22UF 0.1UF 0.1UF 0.1UF 56PF
C192 C193 C194 C195 C196
C212
.
CHIP CHIP CHIP CHIP CHIP
10V 25V 50V 50V 50V
C218
8-7
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
3-064-645-11 HOLDER, FL 3-065-718-11 SINK, HEAT 3-960-273-11 SPACER, TOP END
www
CHIP 13PF 5.00% 50V CHIP 12PF 5.00% 50V CHIP 0.01UF 10.00% 50V CHIP 22PF 5.00% 50V (SLV-EX50AR/EX80SAR/EX90SAR) 1-163-227-11 CERAMIC CHIP 10PF 0.50PF 50V (SLV-EX50BR/EX80SBR/EX90SBR)
QQ 376315150 892498299
TEL 13942296513
CHIP CHIP CHIP CHIP CHIP
Remarks
CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC
QQ
QQ
*
(SLV-EX50BR) A-6713-953-A MA-402 BOARD COMPLETE (SLV-EX80SAR) A-6713-946-A MA-402 BOARD COMPLETE (SLV-EX80SBR) A-6713-952-A MA-402 BOARD COMPLETE (SLV-EX90SAR)
Description
1-163-231-11 1-163-234-11 1-163-234-11 1-164-489-11 1-164-004-11
13942296513
13942296513
1-762-196-21 SWITCH, TACT (I/1 PAUSE)
Part No.
C109 C110 C111 C112 C113
TEL
TEL
S500
Ref. No.
MA-402
http://www.xiaoyu163.com
SLV-LX80S
QQ 376315150 892498299 MA-402
Ref. No.
Part No.
Description
CERAMIC CHIP
0.1UF
C290
1-126-163-11
ELECT
4.7UF
C291
1-164-489-11
CERAMIC CHIP
0.22UF
C292
1-164-505-11
CERAMIC CHIP
2.2UF
C294
1-164-232-11
CERAMIC CHIP
0.01UF
C295
1-164-232-11
CERAMIC CHIP
0.01UF
C296
1-126-157-11
ELECT
10UF
C298
1-126-163-11
ELECT
4.7UF
C299
1-164-232-11
CERAMIC CHIP
1-163-037-11
4.7UF 20.00% 50V 22PF 5.00% 50V (SLV-EX50AR/EX80SAR) CERAMIC CHIP 39PF 5.00% 50V (SLV-EX50BR/EX80SBR/EX90SBR) CERAMIC CHIP 10PF 0.50PF 50V (SLV-EX90SAR) CERAMIC CHIP 0.022UF 10.00% 50V
C303
1-164-505-11
CERAMIC CHIP
C232
1-163-237-11
CERAMIC CHIP
C304
1-164-232-11
CERAMIC CHIP
C232
1-163-231-11
CERAMIC CHIP
C307
1-124-589-11
ELECT
C233 C234 C235
1-163-038-00 1-124-589-11 1-163-038-00
CERAMIC CHIP ELECT CERAMIC CHIP
27PF 5.00% 50V (SLV-EX50AR/EX80SAR) 15PF 5.00% 50V (SLV-EX90SAR) 0.1UF 25V 47UF 20.00% 16V 0.1UF 25V
C308
1-126-964-11
ELECT
C309
1-163-020-00
CERAMIC CHIP
C236 C237 C238 C239 C240
1-163-038-00 1-164-232-11 1-126-157-11 1-164-232-11 1-163-038-00
CERAMIC CERAMIC ELECT CERAMIC CERAMIC
25V 10.00% 50V 20.00% 16V 10.00% 50V 25V
C310
1-126-947-11
ELECT
CHIP CHIP
0.1UF 0.01UF 10UF 0.01UF 0.1UF
C311
1-126-964-11
ELECT
C312
1-124-257-00
ELECT
C241 C242 C243 C244 C245
1-163-038-00 1-163-038-00 1-126-162-11 1-164-232-11 1-126-157-11
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT
0.1UF 0.1UF 3.3UF 0.01UF 10UF
25V 25V 20.00% 50V 10.00% 50V 20.00% 16V
C313
1-126-964-11
ELECT
C314
1-126-947-11
ELECT
C246 C247 C248 C249 C250
1-164-232-11 1-164-489-11 1-124-257-00 1-164-232-11 1-124-589-11
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT
0.01UF 0.22UF 2.2UF 0.01UF 47UF
10.00% 10.00% 20.00% 10.00% 20.00%
C315
1-163-020-00
CERAMIC CHIP
C316
1-126-964-11
ELECT
C317
1-126-160-11
ELECT
C251 C252
1-164-505-11 1-163-263-11
C318
1-126-964-11
ELECT
C252
1-163-127-00
C319
1-126-964-11
ELECT
C253 C254
1-109-982-11 1-163-017-00
CERAMIC CHIP 2.2UF 16V CERAMIC CHIP 330PF 5.00% 50V (SLV-EX50/EX80SAR/EX90SAR) CERAMIC CHIP 270PF 5.00% 50V (SLV-EX80SBR/EX90SBR) CERAMIC CHIP 1UF 10.00% 10V CERAMIC CHIP 0.0047UF 10.00% 50V
C320
1-126-964-11
ELECT
C322
1-126-964-11
ELECT
C255 C256 C257 C258 C259
1-164-161-11 1-164-161-11 1-163-017-00 1-109-982-11 1-163-255-11
C323
1-163-038-00
CERAMIC CHIP
C324
1-164-232-11
CERAMIC CHIP
C326
1-164-489-11
CERAMIC CHIP
C327
1-164-489-11
CERAMIC CHIP
C328
1-164-489-11
CERAMIC CHIP
C350
1-126-157-11
ELECT
C224
1-109-982-11
CERAMIC CHIP
C225 C226 C227 C228
1-164-505-11 1-163-089-00 1-163-255-11 1-163-038-00
CERAMIC CERAMIC CERAMIC CERAMIC
C229 C230
1-126-163-11 1-163-235-11
ELECT CERAMIC CHIP
C230
1-163-241-11
C230
1-163-227-11
C231
CHIP CHIP CHIP CHIP
CHIP CHIP
0.001UF 0.47UF 0.022UF 0.1UF 4.7UF
10.00% 10V (SLV-EX80S/EX90S) 2.2UF 16V 6PF 0.50PF 50V 150PF 5.00% 50V 0.1UF 25V
C262
1-163-243-11
C264
1-163-255-11
50V 16V 50V 50V 16V
CERAMIC CHIP 0.0022UF 10.00% 50V CERAMIC CHIP 0.0022UF 10.00% 50V CERAMIC CHIP 0.0047UF 10.00% 50V CERAMIC CHIP 1UF 10.00% 10V CERAMIC CHIP 150PF 5.00% 50V (SLV-EX50BR/EX80SBR/EX90SBR)
www 1-163-239-11
Remarks
10.00% 25V (SLV-EX90S) 20.00% 50V (SLV-EX90S)
10.00% 16V (SLV-EX90S) 16V (SLV-EX90S) 10.00% 50V (SLV-EX90S) 10.00% 50V (SLV-EX90S) 20.00% 16V (SLV-EX90S)
20.00% 50V (SLV-EX90S) 0.01UF 10.00% 50V (SLV-EX90S) 2.2UF 16V (SLV-EX80S/EX90S) 0.01UF 10.00% 50V (SLV-EX80S/EX90S) 47UF 20.00% 16V (SLV-EX80S/EX90S) 10UF
20.00% 50V (SLV-EX80S/EX90S) 0.0082UF 10.00% 50V (SLV-EX80S/EX90S) 47UF 20.00% 25V (SLV-EX80S/EX90S) 10UF 20.00% 50V (SLV-EX80S/EX90S) 2.2UF 20.00% 50V (SLV-EX80S/EX90S)
QQ 376315150 892498299 10UF
20.00% 50V (SLV-EX80S/EX90S) 47UF 20.00% 25V (SLV-EX80S/EX90S) 0.0082UF 10.00% 50V (SLV-EX80S/EX90S) 10UF 20.00% 50V (SLV-EX80S/EX90S) 1UF 20.00% 50V (SLV-EX80S/EX90S) 10UF
20.00% 50V (SLV-EX80S/EX90S) 10UF 20.00% 50V (SLV-EX80S/EX90S) 10UF 20.00% 50V (SLV-EX80S/EX90S) 10UF 20.00% 50V (SLV-EX80S/EX90S) 0.1UF 25V (SLV-EX80S/EX90S) 0.01UF 10.00% 50V (SLV-EX80S/EX90S) 0.22UF 10.00% 16V (SLV-EX80S/EX90S) 0.22UF 10.00% 16V (SLV-EX80S/EX90S) 0.22UF 10.00% 16V (SLV-EX80S/EX90S) 10UF 20.00% 16V
xiaoy u163. com
CERAMIC CHIP 33PF 5.00% 50V (SLV-EX50BR/EX80SBR/EX90SBR) CERAMIC CHIP 47PF 5.00% 50V (SLV-EX50AR/EX80SAR/EX90SAR) CERAMIC CHIP 150PF 5.00% 50V (SLV-EX50BR/EX80SBR/EX90SBR)
.
Description
1UF
TEL 13942296513
C262
Part No.
8-8
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
1-164-004-11
CHIP CHIP CHIP CHIP
QQ
QQ
C289
CERAMIC CERAMIC CERAMIC CERAMIC ELECT
13942296513
13942296513
Ref. No.
1-163-275-11 1-107-823-11 1-163-037-11 1-163-038-00 1-126-163-11
TEL
TEL
Remarks
5.00% 50V 10.00% 16V 10.00% 50V 25V 20.00% 50V
C219 C220 C221 C222 C223
http://www.xiaoyu163.com
SLV-LX80S
QQ 376315150 892498299 MA-402
Ref. No.
Part No.
Description
Remarks
0.1UF 0.022UF 22UF 10UF 0.0015UF
C357
1-163-011-11
C357
1-163-014-00
C358 C359 C361
1-126-163-11 1-126-157-11 1-126-160-11
CERAMIC CHIP 0.0015UF 10.00% 50V (SLV-EX50AR/EX80SAR/EX90SAR) CERAMIC CHIP 0.0027UF 10.00% 50V (SLV-EX50BR/EX80SBR/EX90SBR) ELECT 4.7UF 20.00% 50V ELECT 10UF 20.00% 16V ELECT 1UF 20.00% 50V
C362
1-126-160-11
ELECT
1UF
C363 C364 C365 C371
1-124-234-00 1-126-163-11 1-164-232-11 1-163-009-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP
C373 C375 C376 C377 C378
1-137-505-11 1-104-696-11 1-163-011-11 1-162-306-11 1-124-589-11
C379 C385 C386
Ref. No.
Part No.
Description
Remarks
C636 C661
1-126-967-11 1-164-232-11
ELECT CERAMIC CHIP
47UF 0.01UF
20.00% 50V 10.00% 50V
C662 C663 C664 C665 C669
1-104-666-11 1-126-941-11 1-124-589-11 1-124-234-00 1-164-232-11
ELECT ELECT ELECT ELECT CERAMIC CHIP
220UF 470UF 47UF 22UF 0.01UF
20.00% 20.00% 20.00% 20.00% 10.00%
25V 25V 16V 16V 50V
C671 C673 C674 C704 C705
1-126-965-91 1-164-232-11 1-126-933-11 1-163-009-11 1-164-232-11
ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP
22UF 0.01UF 100UF 0.001UF 0.01UF
20.00% 10.00% 20.00% 10.00% 10.00%
50V 50V 16V 50V 50V
22UF 4.7UF 0.01UF 0.001UF
20.00% 50V (SLV-EX50) 20.00% 16V 20.00% 50V 10.00% 50V 10.00% 50V
C706 C707 C708 C709 C710
1-126-933-11 1-126-947-11 1-126-163-11 1-163-009-11 1-163-009-11
ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP
100UF 47UF 4.7UF 0.001UF 0.001UF
20.00% 20.00% 20.00% 10.00% 10.00%
16V 25V 50V 50V 50V
MYLAR FILM CERAMIC CHIP CERAMIC ELECT
220PF 0.015UF 0.0015UF 0.01UF 47UF
5.00% 5.00% 10.00% 20.00% 20.00%
C711 C712 C713 C714 C715
1-163-009-11 1-126-933-11 1-164-232-11 1-164-489-11 1-163-989-11
CERAMIC ELECT CERAMIC CERAMIC CERAMIC
0.001UF 100UF 0.01UF 0.22UF 0.033UF
10.00% 50V 20.00% 16V 10.00% 50V 10.00% 16V 10.00% 25V (SLV-EX50)
1-163-038-00 1-126-160-11
CERAMIC CHIP ELECT
C719
1-163-038-00
CERAMIC CHIP
1-126-160-11
ELECT
C720
1-126-157-11
ELECT
10.00% 20.00% 20.00% 10.00%
25V 50V 16V 16V 50V
50V 100V 50V 16V 16V
CHIP CHIP CHIP CHIP
1-124-584-00 1-164-232-11
ELECT CERAMIC CHIP
C453 C454 C455 C456 C457
1-126-157-11 1-163-038-00 1-124-584-00 1-164-232-11 1-126-941-11
ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT
10UF 0.1UF 100UF 0.01UF 470UF
20.00% 16V 25V 20.00% 10V 10.00% 50V 20.00% 25V
C600 C601 C602 C603 C604
1-104-705-11 1-104-705-11 1-113-900-11 1-113-900-11 1-113-900-11
MYLAR MYLAR CERAMIC CERAMIC CERAMIC
0.1UF 0.1UF 470PF 470PF 470PF
20.00% 20.00% 10.00% 10.00% 10.00%
C605
1-107-405-11
C605
1-125-917-11
C606 C607 C608
1-130-470-00 1-107-737-11 1-131-974-11
ELECT(BLOCK) 68UF 20.00% 400V (SLV-EX50AR/EX80SAR/EX90SAR) ELECT(BLOCK) 100UF 20.00% 450V (SLV-EX50BR/EX80SBR/EX90SBR) MYLAR 820PF 5.00% 50V MYLAR 560PF 5.00% 50V FILM 2200PF 5% 800V
CN031 *1-766-716-11 CN051 1-794-861-11 CN072 1-766-978-31 CN072 1-784-484-11 CN105 1-506-470-11
CONNECTOR, BOARD TO BOARD 3P CONNECTOR, BOARD TO BOARD 8P CONNECTOR, FFC/FPC 5P CONNECTOR, FFC/FPC 5P PIN, CONNECTOR 5P
CN201 1-766-984-41
C610 C611 C612 C613 C615
1-137-921-11 1-126-935-11 1-126-960-11 1-130-496-00 1-131-976-21
ELECT ELECT ELECT MYLAR ELECT
1500UF 470UF 1UF 0.12UF 820UF
20% 20.00% 20.00% 5.00% 20%
10V 16V 50V 50V 25V
CN202 *1-560-892-00 CN204 1-691-038-31 CN331 1-766-980-71 CN331 1-784-486-11
CONNECTOR, FFC/FPC 11P (SLV-EX80S/EX90S) PIN, CONNECTOR 4P HOUSING, CONNECTOR 6P (SLV-EX50) CONNECTOR, FFC/FPC 7P CONNECTOR, FFC/FPC 7P
C616 C624 C626 C627 C629
1-126-941-11 1-126-967-11 1-126-967-11 1-164-232-11 1-135-372-31
ELECT ELECT ELECT CERAMIC CHIP ELECT
470UF 47UF 47UF 0.01UF 470UF
20.00% 20.00% 20.00% 10.00% 20%
25V 50V 50V 50V 10V
CN332 CN332 CN334 CN334 CN411
1-506-468-11 1-506-468-11 1-766-980-71 1-784-486-11 1-766-980-71
PIN, CONNECTOR 3P PIN, CONNECTOR 3P CONNECTOR, FFC/FPC 7P CONNECTOR, FFC/FPC 7P CONNECTOR, FFC/FPC 7P
C630 C631 C633
1-164-232-11 1-164-232-11 1-164-232-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01UF 0.01UF 0.01UF
10.00% 50V 10.00% 50V 10.00% 50V
CN411 1-784-486-11 CN412 1-766-978-31
CONNECTOR, FFC/FPC 7P CONNECTOR, FFC/FPC 5P
TEL 13942296513
www
.
0.1UF 25V (SLV-EX80S/EX90S) 10UF 20.00% 16V (SLV-EX80S/EX90S) 100UF 20.00% 16V (SLV-EX80S/EX90S) 0.01UF 10.00% 50V (SLV-EX80S/EX90S) 1UF 20.00% 50V (SLV-EX80S/EX90S)
QQ 376315150 892498299 250V 250V 250V 250V 250V
C722
1-126-933-11
ELECT
C723
1-164-232-11
CERAMIC CHIP
C901
1-126-160-11
ELECT
C902
1-126-160-11
ELECT
C903 C907
1-126-935-11 1-124-589-11
ELECT ELECT
1UF
20.00% 50V (SLV-EX80S/EX90S) 470UF 20.00% 10V 47UF 20.00% 16V
xiaoy u163. com 8-9
http://www.xiaoyu163.com
Note : The components identified by or dotted line with mark mark are critical for safety. Replace only with part number specified.
376315150 892498299
376315150 892498299
C451 C452
0.1UF 25V 1UF 20.00% 50V (SLV-EX80S/EX90S) 1UF 20.00% 50V (SLV-EX80S/EX90S) 100UF 20.00% 10V 0.01UF 10.00% 50V
QQ
QQ
CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP
13942296513
13942296513
1-163-038-00 1-163-037-11 1-124-234-00 1-126-157-11 1-163-011-11
TEL
TEL
C351 C352 C354 C355 C356
http://www.xiaoyu163.com
SLV-LX80S
QQ 376315150 892498299 MA-402
Ref. No.
Part No.
CN412 1-784-484-11 CN600 1-580-230-11
Description
Remarks
CONNECTOR, FFC/FPC 5P PIN, CONNECTOR (PC BOARD) 2P
CNJ901 1-793-001-21 CNJ903 1-779-010-11
JACK, PIN (6P) JACK, PIN 4P
(SLV-EX80S/EX90S) (SLV-EX50)
GL528V1 MPG06D-6052PKG3 1SS119-25TD MPG06D-6052PKG3 MPG06D-6052PKG3
8-719-200-82 8-719-911-19 8-719-911-19
D401 D402
8-719-059-98 8-719-056-06
DIODE MPG06D-6052PKG3 DIODE 1SS119-25TD DIODE 1SS119-25TD (SLV-EX50BR/ EX80SBR/EX90SBR) DIODE SLR-342VCT31 (SLV-EX90S) DIODE SLR-342DCT31 (SLV-EX90S)
D403 D404 D600 D601 D607
8-719-200-82 8-719-109-89 8-719-051-93 8-719-063-70 8-719-109-89
DIODE DIODE DIODE DIODE DIODE
MPG06D-6052PKG3 RD5.6ES-T1B2 DF06M-6031 D1NL20U-TA2 RD5.6ES-T1B2
D608 D609 D611 D612 D613
8-719-022-97 8-719-083-43 8-719-313-17 8-719-313-17 8-719-043-76
DIODE DIODE DIODE DIODE DIODE
D2S4MF 31DQ06-FA7 AU02A-V0 AU02A-V0 AK04V0
D614 D623 D624 D625 D701
8-719-160-64 8-719-109-93 8-719-063-70 8-719-110-49 8-719-150-92
DIODE DIODE DIODE DIODE DIODE
RD16F-T8B1 RD6.2ES-T1B2 D1NL20U-TA2 MTZJ-T-77-18B RD33ES-T1B3
D901 D902
8-719-109-93 8-719-109-93
DIODE RD6.2ES-T1B2 DIODE RD6.2ES-T1B2
TERMINAL BOARD, GROUND TERMINAL BOARD, GROUND
F600
1-532-203-00
FUSE
FH600 1-533-217-31 FH601 1-533-217-31
HOLDER, FUSE HOLDER, FUSE
www
Note : The components identified by or dotted line with mark mark are critical for safety. Replace only with part number specified.
.
8-759-645-07 8-759-831-29 8-759-580-62 8-759-575-72 8-759-589-33
IC IC IC IC IC
LB1943N HD6432197A32FY MM1256AFBE M24C08-WMN6T(A) HA118217LF
IC291 IC301 IC451 IC502 IC600
8-759-566-07 8-759-638-56 8-759-643-83 8-749-015-48 8-749-018-38
IC IC IC IC IC
LA7277M-TLM TDA9605H/N2,557 UPD16315GB-3BS RPM6940 MA8910
IC601 IC660 IC662 IC701
8-759-420-19 8-759-438-18 8-759-471-81 8-742-037-00
IC AN1431T-TA IC PQ12RD08 IC PQ05RD11 HYB IC SBX1837-51
(SLV-EX90S) (SLV-EX80S/EX90S)
(SLV-EX80S/EX90S)
JR001 JR002 JR003 JR004 JR005
1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR006 JR007 JR008 JR009 JR010
1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR011 JR012 JR013 JR014 JR015
1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR016 JR017 JR018 JR019 JR020
1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR021 JR022 JR023 JR024 JR025
1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR026 JR028 JR029 JR030 JR031
1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR032 JR033 JR034 JR035 JR036
1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
QQ 376315150 892498299
TEL 13942296513
ET600 1-537-771-21 ET601 1-537-771-21
IC031 IC101 IC141 IC142 IC201
xiaoy u163. com JR037 JR038 JR039 JR040 JR041
1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR042 1-216-295-00 JR043 1-216-295-00
SHORT SHORT
0 0
8-10
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
D103 D151 D201
Remarks
QQ
QQ
DIODE DIODE DIODE DIODE DIODE
Description
13942296513
13942296513
8-719-048-26 8-719-200-82 8-719-911-19 8-719-200-82 8-719-200-82
Part No.
TEL
TEL
D001 D071 D100 D101 D102
Ref. No.
http://www.xiaoyu163.com
SLV-LX80S
QQ 376315150 892498299 MA-402
Ref. No.
Part No.
Description
Remarks
1-216-295-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR105 JR106 JR107 JR108 JR109
1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR110 JR111 JR112 JR113 JR114
1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR115 JR116 JR117 JR118 JR119
1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR120 JR121 JR122 JR123 JR124
1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR125 JR126 JR127 JR128 JR129
1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00 1-216-296-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
JR130 1-216-296-00 JR131 1-216-296-00 JR132 1-216-296-00
SHORT SHORT SHORT
0 0 0
Part No.
L072 L151 L171 L172 L173
1-414-179-51 1-414-185-51 1-414-185-51 1-414-185-51 1-410-511-11
INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR
2.2UH 22UH 22UH 22UH 15UH
L202 L203 L204 L205 L206
1-414-856-51 1-414-857-51 1-410-510-11 1-414-856-51 1-414-856-51
INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR
10UH 100UH 12UH 10UH 10UH
L207 L211 L214 L215 L372
1-414-856-51 1-414-193-51 1-414-856-51 1-414-187-51 1-414-857-51
INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR
10UH 220UH 10UH 47UH 100UH
L601 L602 L603 L604 L606
1-403-588-11 1-403-588-11 1-414-142-11 1-414-142-11 1-414-142-11
INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR
22UH 22UH 1UH 1UH 1UH
L660 L700 L702 L705
1-410-519-11 1-414-856-51 1-414-856-51 1-414-856-51
INDUCTOR INDUCTOR INDUCTOR INDUCTOR
68UH 10UH 10UH 10UH (SLV-EX80S/EX90S)
L901
1-414-857-51
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
LF600 1-416-929-11
ND451 1-517-734-11
FILTER, LINE
TUBE, FLUORESCENT INDICATOR
PH001 8-749-013-23 PH002 8-749-013-23 PH600 8-749-010-64
(SLV-EX50/ EX80SAR/EX90SAR)
1-216-296-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
(SLV-EX80S/EX90S)
JS712 JS726 JS735 JS737 JS738
1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00 1-216-295-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
(SLV-EX80S/EX90S) (SLV-EX80S/EX90S) (SLV-EX80S/EX90S) (SLV-EX80S/EX90S) (SLV-EX80S/EX90S)
JS901 JS902 JS905 JS906 JS907
1-216-295-00 1-216-295-00 1-216-296-00 1-216-295-00 1-216-295-00
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0
.
100UH
JS291 JS309 JS360 JS379 JS664
www
INDUCTOR
1-216-295-00 1-216-295-00 1-216-296-00 1-216-296-00 1-216-295-00
Remarks
QQ 376315150 892498299
TEL 13942296513
JS151 JS152 JS203 JS204 JS208
Description
(SLV-EX50/EX80S)
PHOTO INTERRUPTER GP3S120 PHOTO INTERRUPTER GP3S120 PHOTO COUPLER PC123FY2
PS031 PS071 PS072 PS331 PS661
1-533-593-51 1-576-384-21 1-576-384-21 1-533-586-51 1-576-384-21
LINK, LINK, LINK, LINK, LINK,
IC IC IC IC IC
xiaoy u163. com (SLV-EX80S/EX90S)
Q001 Q002 Q003 Q153 Q171
8-729-043-84 8-729-043-84 8-729-281-53 8-729-422-27 8-729-421-22
(SLV-EX50) (SLV-EX50)
8-11
http://www.xiaoyu163.com
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
PT380F3 PT380F3 2SC1815GR-TPE2 2SD601A-QRS-TX UN2211-TX
Note : The components identified by or dotted line with mark mark are critical for safety. Replace only with part number specified.
376315150 892498299
376315150 892498299
JR047 JR101 JR102 JR103 JR104
Ref. No.
QQ
QQ
0 0 0
13942296513
13942296513
SHORT SHORT SHORT
TEL
TEL
JR044 1-216-295-00 JR045 1-216-295-00 JR046 1-216-295-00
http://www.xiaoyu163.com
SLV-LX80S
QQ 376315150 892498299 MA-402
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
Remarks
1-216-073-00
R102
1-216-059-00
R102
1-216-049-00
Q205
8-729-421-19
Q206 Q210 Q211 Q301
8-729-421-19 8-729-421-19 8-729-422-27 8-729-216-21
TRANSISTOR UN2213-TX (SLV-EX50BR/EX80SBR/EX90SBR) TRANSISTOR UN2213-TX TRANSISTOR UN2213-TX TRANSISTOR 2SD601A-QRS-TX TRANSISTOR 2SA1162Y-TE85L (SLV-EX80S/EX90S)
R103 R104 R105 R107 R108
1-216-073-00 1-247-807-31 1-249-429-11 1-216-049-00 1-216-073-00
RES-CHIP CARBON CARBON RES-CHIP RES-CHIP
10K 100 10K 1K 10K
5% 5% 5% 5% 5%
1/10W 1/4W 1/4W 1/10W 1/10W
R109 R110 R111 R112 R113
1-216-049-00 1-249-429-11 1-216-081-00 1-216-041-00 1-216-041-00
RES-CHIP CARBON RES-CHIP RES-CHIP RES-CHIP
1K 10K 22K 470 470
5% 5% 5% 5% 5%
1/10W 1/4W 1/10W 1/10W 1/10W
R114 R115 R116 R117 R118
1-216-041-00 1-216-041-00 1-216-089-00 1-249-417-11 1-216-089-00
RES-CHIP RES-CHIP RES-CHIP CARBON RES-CHIP
470 470 47K 1K 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/4W 1/10W
R119 R120 R121 R122 R123
1-216-089-00 1-216-089-00 1-216-049-00 1-216-121-11 1-249-429-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP CARBON
47K 47K 1K 1M 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/4W
R124 R125 R126 R127 R128
1-249-429-11 1-249-437-11 1-216-049-00 1-216-073-00 1-216-073-00
CARBON CARBON RES-CHIP RES-CHIP RES-CHIP
10K 47K 1K 10K 10K
5% 5% 5% 5% 5%
1/4W 1/4W 1/10W 1/10W 1/10W
R129 R130 R131 R132 R133
1-249-441-11 1-216-049-00 1-249-429-11 1-249-429-11 1-216-121-11
CARBON RES-CHIP CARBON CARBON RES-CHIP
100K 1K 10K 10K 1M
5% 5% 5% 5% 5%
1/4W 1/10W 1/4W 1/4W 1/10W
R142 R143 R144 R151 R152
1-247-887-00 1-216-113-00 1-216-105-91 1-216-113-00 1-216-025-11
CARBON RES-CHIP RES-CHIP RES-CHIP RES-CHIP
220K 470K 220K 470K 100
5% 5% 5% 5% 5%
1/4W 1/10W 1/10W 1/10W 1/10W
R153 R154 R155 R156 R157
1-216-073-00 1-216-097-11 1-216-121-11 1-249-435-11 1-216-073-00
RES-CHIP RES-CHIP RES-CHIP CARBON RES-CHIP
10K 100K 1M 33K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/4W 1/10W
R158 R159 R160 R161 R162
1-216-073-00 1-216-049-00 1-216-041-00 1-216-065-00 1-216-073-00
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
10K 1K 470 4.7K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R163 R164 R165 R166 R167
1-216-049-00 1-216-049-00 1-249-429-11 1-216-295-00 1-216-295-00
RES-CHIP RES-CHIP CARBON SHORT SHORT
1K 1K 10K 0 0
5% 5% 5%
1/10W 1/10W 1/4W
R171 R172 R174 R175 R177
1-216-049-00 1-247-807-31 1-216-045-00 1-216-041-00 1-216-065-00
RES-CHIP CARBON RES-CHIP RES-CHIP RES-CHIP
1K 100 680 470 4.7K
5% 5% 5% 5% 5%
1/10W 1/4W 1/10W 1/10W 1/10W
Q302
8-729-200-13
Q303
8-729-200-13
Q372 Q373 Q374
8-729-422-27 8-729-422-27 8-729-424-18
TRANSISTOR 2SC2712Y-TE85L (SLV-EX80S/EX90S) TRANSISTOR 2SC2712Y-TE85L (SLV-EX80S/EX90S) TRANSISTOR 2SD601A-QRS-TX TRANSISTOR 2SD601A-QRS-TX TRANSISTOR UN2113-TX
Q375 Q376 Q377 Q704
8-729-012-31 8-729-900-51 8-729-421-19 8-729-421-19
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
Q706
8-729-421-19
2SC4040-TL2-Q UN2115-QRS(TX) UN2213-TX UN2213-TX (SLV-EX80S/EX90S) TRANSISTOR UN2213-TX
Q707 Q901
8-729-119-76 8-729-424-02
TRANSISTOR 2SA1309A-QRSTA TRANSISTOR 2SB709A-QRS-TX
R001 R003 R004 R005 R006
1-249-413-11 1-249-421-11 1-216-057-00 1-249-401-11 1-249-401-11
CARBON CARBON RES-CHIP CARBON CARBON
470 2.2K 2.2K 47 47
5% 5% 5% 5% 5%
1/4W 1/4W 1/10W 1/4W 1/4W
R007 R008 R009 R010 R032
1-249-437-11 1-249-437-11 1-249-433-11 1-249-433-11 1-216-089-00
CARBON CARBON CARBON CARBON RES-CHIP
47K 47K 22K 22K 47K
5% 5% 5% 5% 5%
1/4W 1/4W 1/4W 1/4W 1/10W
R034 R035 R051 R052 R053
1-216-689-11 1-216-689-11 1-249-425-11 1-216-065-00 1-247-843-11
RES-CHIP RES-CHIP CARBON RES-CHIP CARBON
39K 39K 4.7K 4.7K 3.3K
5% 5% 5% 5% 5%
1/10W 1/10W 1/4W 1/10W 1/4W
R056 R057 R071 R072 R073
1-249-425-11 1-216-073-00 1-216-103-00 1-216-089-00 1-216-049-00
CARBON RES-CHIP RES-CHIP RES-CHIP RES-CHIP
4.7K 10K 180K 47K 1K
5% 5% 5% 5% 5%
1/4W 1/10W 1/10W 1/10W 1/10W
R074 R075 R076 R100 R101
1-216-049-00 1-216-049-00 1-249-417-11 1-216-085-91 1-216-073-00
RES-CHIP RES-CHIP CARBON RES-CHIP RES-CHIP
1K 1K 1K 33K 10K
5% 1/10W 5% 1/10W 5% 1/4W 5% 1/10W 5% 1/10W (SLV-EX50/EX80SBR)
R101
1-216-081-00
RES-CHIP
22K
R101
1-216-077-91
RES-CHIP
15K
5% 1/10W (SLV-EX90SAR) 5% 1/10W (SLV-EX80SAR)
.
10K 5% 1/10W (SLV-EX50AR/EX80SAR/EX90S) RES-CHIP 2.7K 5% 1/10W (SLV-EX50BR) RES-CHIP 1K 5% 1/10W (SLV-EX80SBR)
QQ 376315150 892498299
TEL 13942296513
www
RES-CHIP
xiaoy u163. com 8-12
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
R102
QQ
QQ
TRANSISTOR 2SB709A-QRS-TX TRANSISTOR UN2211-TX TRANSISTOR 2SB709A-QRS-TX TRANSISTOR UN2213-TX TRANSISTOR UN2213-TX (SLV-EX50AR/EX80SAR/EX90SAR)
13942296513
13942296513
8-729-424-02 8-729-421-22 8-729-424-02 8-729-421-19 8-729-421-19
TEL
TEL
Q172 Q174 Q201 Q203 Q204
http://www.xiaoyu163.com
SLV-LX80S
QQ 376315150 892498299 MA-402
Ref. No.
Part No.
Description
Remarks
10K 10K 10K 1K 470
R203
1-247-807-31
R204 R205 R206 R207
1-216-083-00 1-216-069-00 1-216-053-00 1-216-065-00
CARBON 100 5% 1/4W (SLV-EX50BR/EX80SBR/EX90SBR) RES-CHIP 27K 5% 1/10W RES-CHIP 6.8K 5% 1/10W RES-CHIP 1.5K 5% 1/10W RES-CHIP 4.7K 5% 1/10W
R208
1-216-069-00
R208
1-216-073-00
R209
1-216-069-00
R209
1-216-049-00
R211
1-216-295-00
RES-CHIP 6.8K 5% 1/10W (SLV-EX50AR/EX80SAR/EX90SBR) RES-CHIP 10K 5% 1/10W (SLV-EX50BR/EX80SBR/EX90SAR) RES-CHIP 6.8K 5% 1/10W (SLV-EX50AR/EX80SAR) RES-CHIP 1K 5% 1/10W (SLV-EX90SAR) SHORT 0 (SLV-EX90S)
R212
1-216-063-91
RES-CHIP
R212
1-216-051-00
RES-CHIP
R214
1-216-025-11
RES-CHIP
R215 R216
1-216-025-11 1-247-807-31
RES-CHIP CARBON
R222
1-216-041-00
R223
1-216-033-00
R223
1-216-041-00
R224 R225 R226 R228
1-216-049-00 1-249-417-11 1-216-099-00 1-216-041-00
R228
1-216-043-91
R289
1-216-049-00
R291
1-208-806-11
R292
1-216-127-11
R294
1-247-807-31
R295
1-247-807-31
CARBON
100
R296
1-249-428-11
CARBON
8.2K
R299
1-216-071-00
RES-CHIP
8.2K
R301
1-216-073-00
RES-CHIP
10K
R302
1-216-079-00
RES-CHIP
18K
www
.
Part No.
R304
1-216-049-00
R305
1-216-049-00
R306
1-216-083-00
R307
1-216-057-00
R308
1-208-820-11
R309
Description
Remarks
RES-CHIP
1K
5% 1/10W (SLV-EX80S/EX90S) RES-CHIP 1K 5% 1/10W (SLV-EX80S/EX90S) RES-CHIP 27K 5% 1/10W (SLV-EX80S/EX90S) RES-CHIP 2.2K 5% 1/10W (SLV-EX80S/EX90S) METAL CHIP 39K 0.5% 1/10W (SLV-EX80S/EX90S)
1-216-041-00
RES-CHIP
470
R310
1-216-041-00
RES-CHIP
R311
1-216-057-00
RES-CHIP
R312
1-216-083-00
RES-CHIP
R313
1-216-133-91
RES-CHIP
R314
1-216-073-00
RES-CHIP
R317
1-216-061-91
RES-CHIP
R318
1-216-049-00
RES-CHIP
R319
1-216-049-00
RES-CHIP
R322
1-216-295-00
SHORT
5% 1/10W (SLV-EX80S/EX90S) 470 5% 1/10W (SLV-EX80S/EX90S) 2.2K 5% 1/10W (SLV-EX80S/EX90S) 27K 5% 1/10W (SLV-EX80S/EX90S) 3.3M 5% 1/10W (SLV-EX80S/EX90S) 10K
5% 1/10W (SLV-EX80S/EX90S) 3.3K 5% 1/10W (SLV-EX80S/EX90S) 1K 5% 1/10W (SLV-EX80S/EX90S) 1K 5% 1/10W (SLV-EX80S/EX90S) 0 (SLV-EX80S/EX90S)
QQ 376315150 892498299
RES-CHIP 4.7K 5% 1/10W CARBON 2.2M 5% 1/4W RES-CHIP 220 5% 1/10W (SLV-EX50AR/EX80SAR/EX90SAR) RES-CHIP 470 5% 1/10W (SLV-EX50BR/EX80SBR/EX90SBR) RES-CHIP 220 5% 1/10W (SLV-EX50AR/EX80SAR/EX90SAR)
RES-CHIP 470 5% 1/10W (SLV-EX50BR/EX80SBR/EX90SBR) RES-CHIP 1K 5% 1/10W CARBON 1K 5% 1/4W RES-CHIP 120K 5% 1/10W RES-CHIP 470 5% 1/10W (SLV-EX50AR/EX80S/EX90S) RES-CHIP
Ref. No.
560
5% 1/10W (SLV-EX50BR) RES-CHIP 1K 5% 1/10W (SLV-EX90S) METAL CHIP 10K 0.5% 1/10W (SLV-EX90S) RES-CHIP 1.8M 5% 1/10W (SLV-EX50BR/EX80SBR/EX90SBR) CARBON 100 5% 1/4W (SLV-EX90S) 5% 1/4W (SLV-EX90S) 5% 1/4W (SLV-EX90S) 5% 1/10W (SLV-EX90S) 5% 1/10W (SLV-EX80S/EX90S) 5% 1/10W (SLV-EX80S/EX90S)
R327
1-216-041-00
RES-CHIP
R328
1-216-041-00
RES-CHIP
R329
1-216-041-00
RES-CHIP
R350 R351
1-216-073-00 1-216-061-91
RES-CHIP RES-CHIP
5% 1/10W (SLV-EX80S/EX90S) 470 5% 1/10W (SLV-EX80S/EX90S) 470 5% 1/10W (SLV-EX80S/EX90S) 10K 5% 1/10W 3.3K 5% 1/10W
R352 R353 R354 R355 R356
1-216-101-00 1-216-025-11 1-216-085-91 1-216-079-00 1-216-083-00
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
150K 100 33K 18K 27K
5% 5% 5% 5% 5%
R357 R360 R361 R362
1-216-295-00 1-216-077-91 1-249-437-11 1-216-077-91
SHORT RES-CHIP CARBON RES-CHIP
0 15K 47K 15K
5% 5% 5%
R363
1-249-437-11
CARBON
47K
R364 R365 R366 R368 R370
1-216-295-00 1-216-065-00 1-216-041-00 1-216-125-00 1-216-089-00
SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP
0 4.7K 470 1.5M 47K
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
R371 R372 R375 R376 R378
1-249-411-11 1-249-411-11 1-216-073-00 1-216-073-00 1-216-073-00
CARBON CARBON RES-CHIP RES-CHIP RES-CHIP
330 330 10K 10K 10K
5% 5% 5% 5% 5%
1/4W 1/4W 1/10W 1/10W 1/10W
R379 R380 R386
1-249-433-11 1-216-308-00 1-216-057-00
CARBON RES-CHIP RES-CHIP
22K 4.7 2.2K
5% 5% 5%
1/4W 1/10W 1/10W
xiaoy u163. com 8-13
http://www.xiaoyu163.com
470
1/10W 1/10W 1/10W 1/10W 1/10W
1/10W 1/4W 1/10W (SLV-EX50) 5% 1/4W (SLV-EX50)
376315150 892498299
376315150 892498299
1-216-065-00 1-259-880-11 1-216-033-00
1/10W 1/10W 1/10W 1/10W 1/10W
3.9K 5% 1/10W (SLV-EX50/EX80SAR) 1.2K 5% 1/10W (SLV-EX80SBR) 100 5% 1/10W (SLV-EX80S/EX90S) 100 5% 1/10W 100 5% 1/4W
TEL 13942296513 R218 R219 R222
5% 5% 5% 5% 5%
QQ
QQ
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
13942296513
13942296513
1-216-073-00 1-216-073-00 1-216-073-00 1-216-049-00 1-216-041-00
TEL
TEL
R192 R193 R194 R201 R202
http://www.xiaoyu163.com
SLV-LX80S
QQ 376315150 892498299 MA-402
Ref. No.
Part No.
Description
Remarks
RES-CHIP
2.2K
R400
1-216-021-00
RES-CHIP
68
R401
1-249-410-11
CARBON
270
R402
1-249-408-11
CARBON
180
R404 R405 R410
1-249-437-11 1-249-437-11 1-249-403-11
CARBON CARBON CARBON
R411 R414 R415 R416 R417
1-249-419-11 1-216-061-91 1-216-065-00 1-249-427-11 1-249-431-11
R418 R424 R425 R426 R427
Ref. No.
Part No.
Description
Remarks
R710 R711 R717
1-216-097-11 1-249-433-11 1-216-049-00
RES-CHIP CARBON RES-CHIP
100K 22K 1K
R718
1-249-417-11
CARBON
1K
R719
1-249-417-11
CARBON
47K 47K 68
5% 1/4W (SLV-EX90S) 5% 1/4W (SLV-EX90S) 5% 1/4W 5% 1/4W 5% 1/4W
R720
1-249-433-11
CARBON
R721
1-249-433-11
CARBON
CARBON RES-CHIP RES-CHIP CARBON CARBON
1.5K 3.3K 4.7K 6.8K 15K
5% 5% 5% 5% 5%
1/4W 1/10W 1/10W 1/4W 1/4W
R726
1-216-295-00
SHORT
R727 R728 R729
1-216-295-00 1-216-295-00 1-249-429-11
SHORT SHORT CARBON
1-216-089-00 1-216-061-91 1-216-065-00 1-216-069-00 1-216-077-91
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
47K 3.3K 4.7K 6.8K 15K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R730 R731
1-240-307-81 1-249-429-11
FUSIBLE CARBON
R428 R451 R452 R453 R454
1-216-089-00 1-249-413-11 1-216-049-00 1-216-049-00 1-216-049-00
RES-CHIP CARBON RES-CHIP RES-CHIP RES-CHIP
47K 470 1K 1K 1K
5% 5% 5% 5% 5%
1/10W 1/4W 1/10W 1/10W 1/10W
R738 R742 R901
1-216-295-00 1-216-051-00 1-216-097-11
SHORT RES-CHIP RES-CHIP
R902
1-216-097-11
RES-CHIP
R905
1-216-041-00
RES-CHIP
R455 R457 R458 R459 R526
1-249-417-11 1-216-065-00 1-216-065-00 1-216-085-91 1-249-437-11
CARBON RES-CHIP RES-CHIP RES-CHIP CARBON
1K 4.7K 4.7K 33K 47K
5% 5% 5% 5% 5%
1/4W 1/10W 1/10W 1/10W 1/4W
R906 R908 R909 R910 R913
1-216-041-00 1-216-023-00 1-249-407-11 1-216-025-11 1-249-408-11
RES-CHIP RES-CHIP CARBON RES-CHIP CARBON
470 82 150 100 180
5% 5% 5% 5% 5%
1/10W 1/10W 1/4W 1/10W 1/4W
R601 R602 R603 R604 R605
1-214-949-21 1-247-883-00 1-247-891-00 1-249-430-11 1-249-419-11
METAL CARBON CARBON CARBON CARBON
3.3M 150K 330K 12K 1.5K
1% 5% 5% 5% 5%
1/2W 1/4W 1/4W 1/4W 1/4W
R914
1-216-021-00
RES-CHIP
68
5%
1/10W
R606 R607 R611 R612 R613
1-215-444-00 1-249-428-11 1-260-364-11 1-208-789-11 1-249-406-11
METAL CARBON CARBON METAL CHIP CARBON
9.1K 8.2K 1M 2K 120
1% 5% 5% 0.5% 5%
1/4W 1/4W 1/2W 1/10W 1/4W
RV701 1-241-766-11
R614 R615 R616 R617 R618
1-216-655-11 1-216-057-00 1-249-401-11 1-249-417-11 1-249-409-11
METAL CHIP RES-CHIP CARBON CARBON CARBON
1.5K 2.2K 47 1K 220
0.5% 5% 5% 5% 5%
1/10W 1/10W 1/4W 1/4W 1/4W
S101 S102 S454
1-571-958-11 1-771-155-11 1-771-574-21
S458
1-771-574-21
R640 R641 R643 R647 R648
1-219-153-11 1-219-153-11 1-216-353-00 1-215-465-00 1-216-057-00
FUSIBLE 10 FUSIBLE 10 METAL OXIDE 2.2 METAL 68K RES-CHIP 2.2K
5% 5% 5% 1% 5%
1/4W 1/4W 1W 1/4W 1/10W
S459
1-771-574-21
S465
1-771-574-21
R649 R651 R668 R705 R706
1-249-401-11 1-215-459-00 1-216-073-00 1-216-295-00 1-216-295-00
CARBON METAL RES-CHIP SHORT SHORT
47 39K 10K 0 0
5% 1% 5%
1/4W 1/4W 1/10W
S466 S467 S468 S701
1-771-574-21 1-771-574-21 1-771-574-21 1-571-588-11
R707 R709
1-216-295-00 1-216-113-00
SHORT RES-CHIP
0 470K
TEL 13942296513
www
Note : The components identified by or dotted line with mark mark are critical for safety. Replace only with part number specified.
.
5% 5% 5%
1/10W 1/4W 1/10W
5% 1/4W (SLV-EX80S/EX90S) 1K 5% 1/4W (SLV-EX80S/EX90S) 22K 5% 1/4W (SLV-EX80S/EX90S) 22K 5% 1/4W (SLV-EX80S/EX90S) 0 (SLV-EX80S/EX90S) 0 (SLV-EX80S/EX90S) 0 (SLV-EX80S/EX90S) 10K 5% 1/4W (SLV-EX80S/EX90S) 560 5% 1/4W 10K 5% 1/4W (SLV-EX80S/EX90S) 0 1.2K 100K
5% 1/10W 5% 1/10W (SLV-EX80S/EX90S) 100K 5% 1/10W (SLV-EX80S/EX90S) 470 5% 1/10W (SLV-EX80S/EX90S)
QQ 376315150 892498299 RES, ADJ, CERMET 47K (SLV-EX80S/EX90S)
SWITCH, PUSH (1 KEY) (REC PROOF) SWITCH, ROTARY (CAM ENCODER) SWITCH, TACTILE (CHANNEL/TRACKING +) SWITCH, TACTILE (SYNCHRO REC) (SLV-EX90S) SWITCH, TACTILE (COLOR SYSTEM) SWITCH, TACTILE (CHANNEL/TRACKING –) SWITCH, TACTILE (RF CHANNEL) SWITCH, TACTILE (SP/LP) SWITCH, TACTILE (R2) (SLV-EX90S) SWITCH, SLIDE (RF UNIT)
xiaoy u163. com
5%
1/10W
T371 T600
1-423-414-11 1-435-790-11
8-14
http://www.xiaoyu163.com
TRANSFORMER, BIAS OSCILLATION TRANSFORMER, CONVERTER
376315150 892498299
376315150 892498299
1/10W (SLV-EX50) 5% 1/10W
QQ
QQ
5%
13942296513
13942296513
1-216-057-00
TEL
TEL
R387
http://www.xiaoyu163.com
SLV-LX80S
QQ 376315150 892498299 MA-402
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
TU704 1-693-532-11
3-066-370-11 3-066-371-11 VDR600 1-801-267-31
VARISTOR TNR10V431K660 1-476-475-71 1-476-475-81
VIBRATOR, CRYSTAL 10mHz VIBRATOR, CRYSTAL 32.768kHz VIBRATOR, CRYSTAL 14.328224mHz (SLV-EX50AR/EX80SAR/EX90SAR) VIBRATOR, CRYSTAL 14.302444mHz (SLV-EX50BR/EX80SBR/EX90SBR) VIBRATOR, CRYSTAL 3582.056kHz (SLV-EX50AR/EX80SAR/EX90SAR)
X151
1-781-517-11
X201
1-781-577-11
X201
1-578-788-11
X202
*1-760-709-11
VIBRATOR, CRYSTAL 3.575611mHz (SLV-EX50BR/EX80SBR/EX90SBR) VIBRATOR, CRYSTAL 3579.545kHz
#1 #2 #3 #4
1-791-157-31 1-757-665-11
www
.
7-685-648-79 7-685-646-79 7-682-647-09 3-064-472-01
SCREW SCREW SCREW SCREW
+BVTP 3X12 TYPE 2 IT-3 +BVTP 3X8 TYPE 2 IT-3 +PS 3X6 +BVTP 2.6X6 (B TIGHT)
QQ 376315150 892498299
CORD, CONNECTION (NTSC) (SLV-EX50/EX80SBR/EX90S) CORD, CONNECTION (SLV-EX80SBR/EX90SBR) CORD, POWER (SLV-EX50AR/EX80SAR/EX90SAR) CORD, POWER (SLV-EX50BR/EX80BR/EX90BR)
xiaoy u163. com 8-15
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL 13942296513
3-710-901-61 3-970-608-21 3-979-112-01 3-342-512-21 4-921-277-41
HARDWARE LIST ************** SCREW, TAPPING SUMITITE (B3), +BV SCREW SW(+)BVTP 3X10 SCREW (B1.7X3.5), TAPPING SCREW (B2.8X8), TAPPING BIND
QQ
QQ
MISCELLANEOUS **************
(SLV-EX50AR/ EX80S/EX90AR) MANUAL, INSTRUCTION (SLV-EX50BR/ EX90BR) COMMANDER, STANDARD (RMT-V312) (SLV-EX50/EX80S) COMMANDER, STANDARD(RMT-V312A) (SLV-EX90S)
13942296513
13942296513
1-767-855-11 1-579-463-11 1-795-327-11
MANUAL, INSTRUCTION
TEL
TEL
X101 X102 X151
1-575-795-61
Remarks
TUNER (BTF-3MA413)
1-696-592-41
Description
ACCESSORIES ************
http://www.xiaoyu163.com
SLV-LX80S SLV-EX50/EX80S/EX90S
QQ 376315150 892498299
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
Remarks
TEL
TEL
13942296513
13942296513
9-921-798-11
.
xiaoy u163. com Sony Corporation
HOME VIDEO COMPANY
–8-16 96 –
http://www.xiaoyu163.com
2001F0800-1 2001. 6 Published by Quality Assurance Dept.
376315150 892498299
376315150 892498299
www
QQ
QQ
QQ 376315150 892498299
TEL 13942296513