Transcript
ADC Automation Hardware Specifications
ADC Automation Hardware Specifications About this document This document presents specifications for computer hardware being shipped for ADC systems as of the date of this specification sheet. This hardware supports both ADC v11 and ADC v12 automation platforms.
History Version
Date
Description
1
19-Dec-2005
Updated doc format. Hardware spec review and update.
2
16-Aug-2007
Hardware spec review and update.
3
3-May-2010
Hardware spec review and update. Addition of Device Controller 4RU and 2RU.
4
9-August-2010
Hardware spec review and update.
5
2-Sept-2011
Client Workstation Hardware update.
6
2-May-2012
Added note on RS232 port for panels to Client section.
7
20-Jan-2014
New Template
File Server The basic specifications for an ADC file server are….
1RU SuperServer - Dual Xeon Processor, Redundant 650W PS 2x 1-Gigabit Ethernet Module Intel Quad Core Xeon (E5504) 2.0Ghz 1066Mhz FSB
© 2014 Imagine Communications Corp.
Proprietary and Confidential
27-March-2014| Page 1 of 6
ADC Automation Hardware Specifications
1GB 1333Mhz non ECC 250GB SATA 3.0GB/s 1U IO Riser Card for X8DTU (PCIe / PCIx Riser Rev 2.0) Operating System: Microsoft® Windows® Server 2008
Client Workstation The following specifications outline the basic recommended workstation options: IMPORTANT: An RS-232 serial port utilizing a 9-pin connector is required for any client computer that will be utilized with an automation hardware control panel.
Comparison Note A typical Client is an HP Compaq 6200 Pro Business PC or an HP Compaq 8200 Elite Business PC.
For customer supplied units, either model or their chassis variants (Microtower – MT, Convertible Minitower – CMT, or Small Form Factor - SFF ) will work.
The 6200 Pro Business PC offers the same Intel Processors and graphics as the 8200, however it is less expandable, and – if expandability is not an issue - a little less costly.
Caution: The Small Form Factor (SFF) chassis is a better fit for a unit that is going to be placed in a rack, but it only has low profile slots, so if any additional cards are to be fitted there may be an issue. This is specifically an issue for the List Redundancy Client where the full height GPI card is installed.
Note: Imagine Communincations- supplied units are the HP Compaq 6200 Pro Business PC in the microtower (MT) chassis.
6200 Compaq Pro Business PC Basic specifications for this ADC workstation client are….
Intel 2nd Generation Core™ i3, i5, i7 Processors
Integrated Intel® HD Graphics 2000/3000; HP DisplayPort
Up to 1TB hard disk drive; up to 160GB solid state drive, DDR3 SDRAM; (4) DIMM slots enabling up to 16GB HP USB 2-button Optical scroll Mouse, HP USB Standard Keyboard, HP Serial Port Adapter DVD-ROM drive, SuperMulti Writer Drive11, HP Blu-ray Writer Drive12, HP 22-in-1 Media Card Reader
© 2014 Imagine Communications Corp.
Proprietary and Confidential
27-March-2014| Page 2 of 6
ADC Automation Hardware Specifications
HP 802.11 b/g/n Wireless NIC: Integrated Intel 82579M GbE Network Connection supporting vPro remote management technologies. (NOTE: The integrated network connection is required to support Intel vPro Technology.) Note: Additional Intel Network Interface Cards may be required for systems connecting to external networks, or a database using TCP/IP.
Expansion Slots: •
MT: One PCI, two PCIe x1 slots, one PCIe x16 slot
•
SFF: Low profile: One PCI, two PCIe x1 slots, one PCIe x16 slot
Power Supply •
MT: 320W Power Supply, Active PFC; 90% efficient power supply available as an option
•
SFF: 240W Power Supply, Active PFC; 90% efficient power supply available as an option
Operating System: Microsoft® Windows® 7: 32Bit Dimensions (HxWxD) •
MT: 14.9 x 7.0 x 17.0 in (377 x 177 x 431 mm)
•
SFF: 4.0 x 13.3 x 14.9 in (100 x 338 x 379 mm)
HP 8200 Elite Business PC Basic specifications for this ADC workstation client are….
Intel 2nd Generation Core™ i3, i5, i7 Processors (select processors include Intel vPro™ Technology7)
Up to 1TB hard disk drive; up to 160GB solid state drive, DDR3 SDRAM; (4) DIMM slots enabling up to 16GB
Integrated Intel® HD Graphics 2000/3000; HP DisplayPort
HP USB 2-button Optical scroll Mouse, HP USB Standard Keyboard, HP Serial Port Adapter DVD-ROM drive, SuperMulti Writer Drive11, HP Blu-ray Writer Drive12, HP 22-in-1 Media Card Reader HP 802.11 b/g/n Wireless NIC: Integrated Intel 82579M GbE Network Connection supporting vPro remote management technologies. •
Note: The integrated network connection is required to support Intel vPro Technology.
•
Note: Additional Intel Network Interface Cards may be required for systems connecting to external networks, or a database using TCP/IP.
Expansion Slots: •
CMT: Three PCI, one PCIe x1 slots, two PCIe x16 slot
•
SFF: Low profile: One PCI, one PCIe x1 slots, two PCIe x16 slot
© 2014 Imagine Communications Corp.
Proprietary and Confidential
27-March-2014| Page 3 of 6
ADC Automation Hardware Specifications
Power Supply •
CMT: 320W Power Supply, Active PFC; 90% efficient power supply available as an option
•
SFF: 240W Power Supply, Active PFC; 90% efficient power supply available as an option
Operating System: Microsoft® Windows® 7: 32Bit Dimensions (HxWxD) •
CMT: 17.6 x 7.00 x 17.5 in (448 x 178 x 445 mm)
•
SFF: 4.0 x 13.3 x 14.9 in (100 x 338 x 379 mm)
ADC Device Controller 4RU chassis ADC Device Controller 4RU use a single-board computer. The basic specifications for this Device Controller are listed below. Note: While their chassis size is different, the ADC Device Controller 4RU chassis and ADC Device Controller 2RU chassis share a majority of common hardware components.
Custom front panel
DVD ±R, 16X, dual layer
Single Board Computer (SBC):
Intel Pentium 4, 3.0GHz, LGA 775 (upgradeable)
250GB SATA removable hard drive (Optional) Raided Hard Drives: RAID 1 for storage (with a second, removable drive), ADC playout automation’s RAID solution is implemented on this ATA RAID controller. 14 card passive backplane: 13 PCI and 1 PICMG v1.3 4 GB SDRAM system memory Note: The available memory may be limited to approximately 3GB, with 4GB of physical memory installed, based on architectural and operating system restrictions.
Dual Redundant 300-Watt Power Supplies: Universal input voltage, AC plug on each module, no common components, no standby voltages when power module switch is OFF.
CompactFlash Socket CPU fans: Fan1, Fan2, w/ sensors Temp1, Temp2 (Chassis fans are hot swappable) USB Ports: 1 USB port on front, 2 USB ports on rear Serial, Parallel, and Alarm Ports on the chassis Single PS2 connector located on the SBC, with a Y connector supplied- USP keyboard and mouse also supported
© 2014 Imagine Communications Corp.
Proprietary and Confidential
27-March-2014| Page 4 of 6
ADC Automation Hardware Specifications
Network Interface Cards: 2 GigE NICs onboard VGA Graphics output onboard LTC TimeCode Card w/ video sync Serial Cards •
8-Port Serial Card
•
16-Port Serial Card
Note: The number of Serial Cards in any one machine depends on the number of devices being controlled - up to a maximum of eight Serial-8 cards or four Serial-16 cards. These cards cannot be mixed in a single chassis.
GPI Card - 8 in / 8 out per card, 2 cards standard, up to 4 total Operating System: Microsoft® Windows® Server 2008. Chassis Specs: •
Height: 4RU (17.78 cm)
•
Width: 19” Rackmount standard (48.26 cm)
•
Depth: 21.26” (54 cm)
•
Weight: 41 lbs (18.6KG)
ADC Device Controller 2RU chassis The ADC Device Controller 2RU chassis use a single-board computer and provide a solution for sites requiring a smaller hardware footprint. The basic specifications for this Device Controller are listed below. Note: While their chassis size is different, the ADC Device Controller 4RU chassis and ADC Device Controller 2RU chassis share a majority of common hardware components.
Custom front panel Single Board Computer (SBC):
Intel Pentium 4, 3.0GHz, LGA 775 (upgradeable)
250GB SATA removable hard drive DVD ±R, 16X, dual layer 5 card passive backplane: 5 PCI + 1 PICMG v1.3 4 GB SDRAM system memory Note: The available memory may be limited to approximately 3GB, with 4GB of physical memory installed, based on architectural and operating system restrictions.
© 2014 Imagine Communications Corp.
Proprietary and Confidential
27-March-2014| Page 5 of 6
ADC Automation Hardware Specifications
Dual Redundant 300-Watt Power Supplies: universal input voltage, AC plug on each module, no common components, no standby voltages when power module switch is OFF.
CompactFlash Socket
CPU fans: Fan1, Fan2, w/ sensors Temp1, Temp2 (Chassis fans are hot swappable) USB Ports: 2 USB ports on front and 2 USB pots on the rear Serial, Parallel, and Alarm ports all on chassis Single PS2 connector located on the SBC, with a Y connector supplied- USP keyboard and mouse also supported 2 GigE NICs onboard VGA Graphics display onboard LTC TimeCode Card w/ video sync Serial Cards •
8-Port Serial Card (maximum 3 cards)
•
16-Port Serial Card (maximum 2 cards)
IMPORTANT: Note: The number of Serial Cards in any one machine depends on the number of devices being controlled. Serial-8 and Serial-16 cards cannot be mixed in the same chassis.
GPI Card - 8 in / 8 out per card, 2 cards standard, up to 4 total Operating System: Microsoft® Windows® Server 2008. Chassis Specs: •
Height: 2RU (8.89 cm)
•
Width: 19” Rackmount standard (48.26 cm)
•
Depth: 19” (48.26 cm)
•
Weight: 35 lbs (15.9KG)
© 2014 Imagine Communications Corp.
Proprietary and Confidential
27-March-2014| Page 6 of 6
