Transcript
SMART GET IT TOGETHER STATION WARNING: Electrical shock hazard may cause death or serious injury. Do not operate Speaker using AC adapter near water. AC adapter is meant for indoor use only. Always plug adapter into Speaker before plugging into outlet. Note: •
For safety and ease of assembling, installation is recommended using two people.
Tools needed: #2 Phillips screw driver Parts Included: B. (1) Top Panel C. (10) Push Pin D. (8) Small Bolt E. (6) Bolt F. (2) Side bar
G. (1) Cover Panel H. (1) Stereo Cord I. (1) 7 Plug Power Strip J. (1) AC Adapter K. (5) iPod Dock
Assembling Instructions: 1. Attach the Top Panel (B) to the Station Base (A) by inserting Bolts (E) through the pre-drilled holes located at the bottom of the Top Panel (B) and into the corresponding pre-drilled holes in the base of the Station. . 2. Tighten the two Side bars (F) on both side of the station base (A) by inserting the Small Bolt (D) through the pre-drilled holes in the bars and into the side panels. Operating Instructions: 1. Make sure Speaker is turned off (Rotate Volume dial all the way to the left). 2. Insert small end of the enclosed AC Adapter (J) into the Adapter Input located in the power supply box (G). (Refer the illustration on the next page). 3. Plug the standard end of the adapter into a Power Strip (I) socket in the power supply box (G). The Power Strip plug comes out from the back of the Station and should be plugged into a 120V AC power source (Standard wall outlet). NOTE: Use only power adapters with the following specifications: Input AC 120V 60 Hz; Output: DC 12V 1000mA, UL Listed. 4. To use an iPod with the Station, first turn the speaker off (rotate the Volume dial all the way to the left.), Then attach the iPod to the dock located at the front center of the docking station. This docking station will automatically function as a charging unit for your iPod product. * Included is a set of 5 Universal Dock adapters (K). These adapters allow you to connect most models of the iPod that won’t work using the standard dock. * Included a set of 5 Universal Docks (K): 1. iPod Classic 80GB 2. iPod Classic 160GB www.pbteen.com
•
4. iPod Nano Generation 3 4GB/8GB 5. iPod Touch 8GB/16GB/32GB To play with MP3 Plug stereo cord (H) into the audio jack (next to the power indicator light see illustration as below). Plug the other end of the Stereo Cord into the headphones jack on your MP3 player.
5. Turn the speaker on by rotating the volume control knob to the right until you see the power indicator light next to the volume knob stand illuminate. 6. Play music using iPod or MP3’s controls and adjust the volume either by using the speaker shelf’s volume knob (rotating the dial to the right increases the volume) or your MP3 player’s volume control. You may need to experiment to find the right volume setting for iPod or the MP3 player and/or the speaker set.) Note: The audio jack and iPod speaker can not play music at the same time. When you play music through iPod pin docking please make sure to plug off the audio jack. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help Care Instructions: • Dust with a soft, dry cloth. • Do not use glass cleaner, abrasives, wax or household cleaners as they may damage the finish on the product www.pbteen.com
Anti Tip mounting: Parts Included: L. (2) 1-1/2” Wall mounting screw M. (2) 1/2” Screw
N. (2) “L” metal plate O. (2) Plastic anchor
To avoid item tilting forward, mounting to the wall is recommended. For safe mounting, it is essential to use the proper hardware for your wall type (Drywall, concrete, etc). Contact your local hardware store for assistance if necessary. Mount to wood studs whenever possible. 1. Tighten the adjustable “L” metal plate (N) on the right and Left side panel of the item on pre-drill hole by using 1/2” round head screw (M). 2. Place the Smart station at the desired position. Mark the insertion point for the plastic anchor (O). 3. Using the plastic anchor (O) included or the proper hardware for your wall type. Drill 1/4” hole, insert the plastic anchor (O) into the wall, and tighten the adjustable “L” metal plate (N) to the plastic anchor (O) by using 1-1/2” mounting screw (L). 4. May adjust the “L” Metal plate (N) to have item flush with the wall.
www.pbteen.com
