Transcript
SmartSwitch Upgrade/Replacement Instructions These instructions explain how to install a SmartSwitch Service/System Selector (SmartSwitch) to upgrade a TracVision HD11 system (with one HD11 antenna and ACU) or replace a previously installed SmartSwitch. IMPORTANT!
For instructions on installing the SmartSwitch and one or two TracVision HD11 systems together, refer to the TracVision HD11 Installation Guide. For SmartSwitch operation instructions, refer to the TracVision HD11 User’s Guide.
Installation Steps 1. Inspect Parts and Gather Tools............................ 3 2. Plan the Installation............................................... 4 3. Mount the SmartSwitch........................................ 5 4. Wire the SmartSwitch ........................................... 7 5. Launch the Setup Wizard (Upgrades Only) ...... 8
Who Should Install the System? To ensure a safe and effective installation, KVH requires that a KVH-certified marine technician install the SmartSwitch. KVH-certified technicians have the tools and electronics expertise necessary to install the system. To find a technician near you, visit www.kvh.com/ wheretogetservice.
Technical Support If you need technical assistance, please contact KVH Technical Support: Europe, Middle East, Africa, Asia Phone: +45 45 160 180 E-mail:
[email protected] (Mon.-Fri., 8 am-4:30 pm, +1 GMT) North/South America, Australia, New Zealand Phone: +1 401 847-3327 E-mail:
[email protected] (Mon.-Fri., 9 am-6 pm ET, -5 GMT) (Sat., 9 am-2 pm ET, -5 GMT)
KVH, TracVision, and the unique light-colored dome with dark contrasting baseplate are registered trademarks of KVH Industries, Inc. All other trademarks are property of their respective companies. The information in this document is subject to change without notice. No company shall be liable for errors contained herein. © 2012 KVH Industries, Inc., All rights reserved. 54-0816 Rev. A
1
1 Inspect Parts and Gather Tools Before you begin, follow these steps to make sure you have everything you need to complete the installation. a. Unpack the box and ensure it contains everything shown on the Kitpack Contents List.
Figure 1 SmartSwitch ®
POWER
•
PC (preferably with Internet access)
16.31" (41.43 cm)
Strain Relief Bracket
c. Gather the following tools. You will need these tools to complete the installation. #1 Phillips screwdriver
PORT/A STBD/B ANTENNA INPUT
2 3 MULTISWITCH OUT
Figure 2 SmartSwitch Dimensions
b. Carefully examine all of the supplied parts to ensure nothing was damaged in shipment.
•
1
Top View
11.18" (28.40 cm)
19.00" (48.26 cm)
Side View
2.63" (6.68 cm)
1.75" (4.45 cm)
Front View
4 x ø.25" (0.64 cm)
16.75" (42.55 cm) 18.31" (46.51 cm)
0.44" (1.12 cm)
3
2 Plan the Installation Follow the steps below to plan the SmartSwitch installation.
Select an Installation Location
Figure 3 SmartSwitch Mounting Options
SmartSwitch Rack Mount ®
POWER
1
PORT/A STBD/B ANTENNA INPUT
2 3 MULTISWITCH OUT
When selecting an installation location, consider the following: •
•
Choose a Mounting Option Select one of the following SmartSwitch mounting options.
4
Rack Mounting Bracket (x2)
Choose a belowdecks installation location that is dry, well-ventilated, and away from any heat sources or salt spray. The SmartSwitch must be installed within 3 feet (1 m) of the ACU A (the TracVision HD11 Antenna Control Unit (ACU) connected to Antenna A) in order to use the supplied PC data cable. However, longer cabling may be used – contact KVH for details.
•
You can mount the SmartSwitch in a standard 19" (48.26 cm) equipment rack, either separately or together with an ACU (see Figure 3). The SmartSwitch is 1.5U in height.
•
Alternatively, you can mount the SmartSwitch to a horizontal surface; the horizontal surface mounting brackets can attach to either the top or bottom of the SmartSwitch (see Figure 3).
1.5U
ACU/SmartSwitch Joint Rack Mount TRAC KING DIRE CTV
® CONTROL UNIT
MENU
CHANGE
S ATS
99/101/103 ACCEPT
EXIT
ANTENNA POWER
3U ®
POWER
1
2 3 MULTISWITCH OUT
PORT/A STBD/B ANTENNA INPUT
Joint Rack Mounting Bracket (x2) SmartSwitch Horizontal Surface Mount ®
POWER
1
2 3 MULTISWITCH OUT
PORT/A STBD/B ANTENNA INPUT
Horizontal Surface Mounting Bracket (x2)
3 Mount the SmartSwitch Follow the steps below to mount the SmartSwitch using the desired mounting option.
Figure 4 Strain-Relief Bracket Mounting
Rack Mounting a. Attach the strain-relief bracket to the SmartSwitch, as shown in Figure 4. Using a #1 Phillips screwdriver, secure the bracket in place using four #6-32 screws and #6 washers (supplied in the kitpack). b. Secure the SmartSwitch to the rack using four M6 screws and washers (see Figure 5).
#6-32 Screw (x4)
#6 Washer (x4)
Figure 5 SmartSwitch Rack Mounting
Mounting Hole (x4)
Horizontal Mounting a. Using a #1 Phillips screwdriver, remove the six screws securing the rack mounting brackets to the SmartSwitch (see Figure 6). b. Using a #1 Phillips screwdriver, attach the two horizontal mounting brackets to the sides of the SmartSwitch using four supplied #6-32 screws and #6 washers (see Figure 7). You can attach the brackets to either the top or bottom of the SmartSwitch, depending on your desired mounting location. c. If you are mounting the SmartSwitch to the underside of a shelf, attach the strain-relief bracket, as shown in Figure 4. Using a #1 Phillips screwdriver, secure the bracket in place using four #6-32 screws and #6 washers (supplied in the kitpack). d. Using fasteners appropriate for the mounting surface, secure the SmartSwitch to the mounting surface using the four mounting bracket holes.
Strain-Relief Bracket
®
POWER
1
2 3 MULTISWITCH OUT
PORT/A STBD/B ANTENNA INPUT
M6 Screw and Washer (x4)
Figure 6 SmartSwitch Rack Mounting Bracket Removal
Rack Mounting Bracket (x2)
#6-32 Screw (x6)
Figure 7 Horizontal Mounting
Horizontal Mounting Bracket (x2)
#6 Washer (x6)
Strain-Relief Bracket
#6-32 Screw (x6)
5
3 Continued Mount the SmartSwitch Joint ACU/SmartSwitch Rack Mounting a. Using a #1 Phillips screwdriver, remove the six screws securing the rack mounting brackets to the SmartSwitch (see Figure 6 on page 5). b. Repeat Step a. to remove the six screws securing the rack mounting brackets to the ACU. c. Attach the joint rack mounting brackets to the ACU and SmartSwitch, as shown in Figure 8. Secure the brackets in place using twelve #6-32 screws and washers (supplied in the kitpacks). d. Attach the strain-relief bracket and retaining straps, as shown in Figure 8. Secure them in place using eight #6-32 screws and #6 washers (supplied in the kitpacks). NOTE: Only the SmartSwitch strain-relief bracket must be installed. The ACU does not require a strainrelief bracket when jointly mounted with the SmartSwitch. e. Secure the joint assembly to the rack using four M6 screws and washers.
6
Figure 8 ACU/SmartSwitch Joint Assembly
ACU
Joint Rack Mounting Bracket (x2)
SmartSwitch
#6-32 Screw (x20) #6 Washer (x20)
Retaining Strap (x2)
Strain-Relief Bracket
4 Wire the SmartSwitch
ACU A B (+)
A (–)
Green/Red
Red/Green
Orange/Red
Red/Orange
Green/White
White/Green
NMEA Blue/White
White/Blue
Orange/White
White/Orange
Gray/White
Red (+48V)
Black (Gnd)
White/Gray
SmartSwitch Controller
Brown/White
To Antenna
Wire Color/Stripe Color
Ethernet
White/Brown
Single Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
CAUTION
Maintenance RS232
RISK OF ELECTRIC SHOCK DO NOT OPEN
Meets
requirements
WiFi
Tested to comply with FCC Standards This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Fuse 3.15A 250V ~ Fast Acting
KVH and TracVision are registered trademarks of KVH Industries, Inc.
ACU B B (+)
A (–)
Green/Red
Red/Green
Orange/Red
Red/Orange
Green/White
White/Green
NMEA Blue/White
White/Blue
Orange/White
White/Orange
SmartSwitch Controller
Brown/White
To Antenna
Wire Color/Stripe Color
Ethernet
White/Brown
Single Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
Gray/White
Only DIRECTV® programming in North America supports SWM-compatible receivers and DVRs (see Figure 10). All linear receivers/ DVRs and other circular receivers/DVRs are not SWM-compatible.
Antenna B (If equipped)
Red (+48V)
Wiring SWM and Non-SWM Hardware
Antenna A
Black (Gnd)
NOTE: To help ensure proper cable connections, be sure to apply the cable labels (supplied in the kitpack) to the cables that will connect the SmartSwitch to other system components.
Figure 9 Wiring Overview
White/Gray
Wiring instructions vary according to the customer’s specific system configuration and hardware. Refer to the wiring diagrams provided in Appendix A on page 9 for complete wiring instructions.
CAUTION
Maintenance RS232
RISK OF ELECTRIC SHOCK DO NOT OPEN
Meets
requirements
WiFi
Tested to comply with FCC Standards This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Fuse 3.15A 250V ~ Fast Acting
KVH and TracVision are registered trademarks of KVH Industries, Inc.
SmartSwitch PORT/A ANTENNA INPUT
STARBOARD/B ANTENNA INPUT TO ACU
18V
18V
13V 18V/22KHZ 13V/22KHZ MULTISWITCH OUT 1
13V
18V/22KHZ 13V/22KHZ
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ MULTISWITCH OUT 3
13V
18V/22KHZ 13V/22KHZ
IMPORTANT!
Unless specified otherwise, receivers/DVRs in the following wiring diagrams are not SWM-compatible.
NOTE: Additional SWM-compatible receivers/DVRs might become available at any time. If your receiver or DVR model is not listed here, check its manual to see if it is SWM-compatible.
Receiver/DVR Receiver/DVR Receiver/DVR Group 1 Group 2 Group 3
Figure 10 SWM-Compatible Receivers/DVRs
Receivers
DVRs
H20
HR21, HR21 Pro
H21
HR22
H22
HR23
H23
HR24
H24
HR34/HMC*
H25
R16
SmartSwitch Output Wiring Diagrams
D12
R20
•
Overview (see page 11)
D13
R22
•
32 Non-SWM-compatible Tuners (see page 12)
SmartSwitch Input Wiring Diagrams •
One TracVision HD11 Antenna/ACU (see page 9)
•
Two TracVision HD11 Antennas/ACUs (see page 10)
•
16 SWM-compatible Tuners and 32 NonSWM-compatible Tuners (see page 13)
•
32 SWM-compatible Tuners and 32 NonSWM-compatible Tuners (see page 14)
*NOTE: Unlike other DVRs, the HR34 Home Media Center uses five tuners. Therefore, if you connect this DVR, be sure to reserve five tuners instead of two. Refer to the DVR’s manual for complete wiring details.
7
5 Launch the Setup Wizard (Upgrades Only) If you are upgrading the TracVision HD11 system to include a SmartSwitch, follow the steps below to launch the Setup Wizard and reconfigure system settings. If you are replacing a previously installed SmartSwitch, the procedure is complete (your system is already configured). a. Press the power button on the front of the ACU to apply power to the TracVision system. Then wait 1 minute for system startup. b. Open the web browser on a PC connected to the same network. Then type the ACU’s serial number into the browser’s address bar, as shown below: http://hd11-
.local NOTE: For example, if the serial number was 123456789, you would enter the following into the browser’s address bar: http://hd11-123456789.local
Figure 11 ACU Power Button
TRACKING DIRECTV
® CONTROL UNIT
MENU
ACCEPT
EXIT
Power Button
Figure 12 ACU Serial Number Location
T R AC K I N G D I R E C T V
® CONTROL UNIT
MENU
CHANGE
S AT S
9 9 / 1 0 1 / 1 0 3 ACCEPT
EXIT
ANTENNA POWER
123456789
Serial Number on Rear Panel
Figure 13 Launch Setup Wizard Button
c. Log into the web interface: Username: admin Password: password d. Select Settings/General Settings. Then select the “Launch” Button to launch the Setup Wizard (see Figure 13).
8
S ATS
99/101/103
POWER
TIP: The ACU serial number location is shown in Figure 12.
e. Follow the Setup Wizard’s onscreen instructions to reconfigure system settings (see Figure 14).
CHANGE
ANTENNA
Figure 14 Setup Wizard
A Wiring Diagrams Appendix
Wiring SmartSwitch Input: One TracVision HD11 Antenna/ACU Antenna
18V Power/Data
13V 18V/ 22KHz
Network
ACU
13V/ 22KHz
Terminal Strip A (–)
B (+)
Green/Red
Red/Green
Orange/Red
Red/Orange
Green/White
White/Green
NMEA Blue/White
White/Blue
Black (Gnd)
Orange/White
Red (+48V)
White/Orange
Gray/White
White/Gray
Brown/White
To Antenna
Wire Color/Stripe Color
SmartSwitch Controller
Ethernet
White/Brown
Single Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
Maintenance RS232
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN
Meets
requirements
WiFi
Tested to comply with FCC Standards
Fuse 3.15A 250V ~ Fast Acting
Power
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
KVH and TracVision are registered trademarks of KVH Industries, Inc.
SmartSwitch Controller Ferrite Clamp
18V
13V
13V/ 18V/ 22KHz 22KHz
Connect Cable End with Ferrite Clamp to ACU
SmartSwitch
PORT/A ANTENNA INPUT
STARBOARD/B ANTENNA INPUT TO ACU
18V
18V
13V 18V/22KHZ 13V/22KHZ MULTISWITCH OUT 1
13V
18V/22KHZ 13V/22KHZ
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ MULTISWITCH OUT 3
13V
To ACU
18V/22KHZ 13V/22KHZ
9
A Continued Wiring Diagrams Wiring SmartSwitch Input: Two TracVision HD11 Antennas/ACUs Starboard Antenna (B)
Port Antenna (A)
Power/Data
Power/Data 13V/ 22KHz
18V
18V/ 22KHz
13V
SmartSwitch
18V/ 22KHz
13V
13V/ 22KHz
18V
18V/ 22KHz
13V
18V/ 22KHz
13V
13V/ 22KHz
18V
13V/ 22KHz
18V
PORT/A ANTENNA INPUT
STARBOARD/B ANTENNA INPUT TO ACU
18V
13V 18V/22KHZ 13V/22KHZ MULTISWITCH OUT 1
18V
13V
18V/22KHZ 13V/22KHZ
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ MULTISWITCH OUT 3
13V
To ACU
18V/22KHZ 13V/22KHZ
Ferrite Clamp Port ACU (A)
Connect Cable End with Ferrite Clamp to ACU
Terminal Strip A (–)
B (+)
Green/Red
Red/Green
Orange/Red
Red/Orange
Green/White
White/Green
NMEA Blue/White
White/Blue
Orange/White
White/Orange
Gray/White
White/Gray
Red (+48V)
Black (Gnd)
SmartSwitch Controller
Brown/White
To Antenna
Wire Color/Stripe Color
Ethernet
White/Brown
Single Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
Maintenance RS232
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN
Meets
requirements
WiFi
Tested to comply with FCC Standards
Fuse 3.15A 250V ~ Fast Acting
Power
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
KVH and TracVision are registered trademarks of KVH Industries, Inc.
SmartSwitch Controller
Network
Starboard ACU (B) Terminal Strip A (–)
B (+)
Green/Red
Red/Green
Orange/Red
Red/Orange
Green/White
White/Green
NMEA Blue/White
White/Blue
Orange/White
White/Orange
Gray/White
White/Gray
Black (Gnd)
Red (+48V)
SmartSwitch Controller
Brown/White
To Antenna
Wire Color/Stripe Color
Ethernet
White/Brown
Single Phase AC Input 100-240V ~ 200W MAX 50/60 Hz
Maintenance RS232
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN
Meets
requirements
Tested to comply with FCC Standards
Fuse 3.15A 250V ~ Fast Acting
Power Network 10
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
KVH and TracVision are registered trademarks of KVH Industries, Inc.
WiFi
A Continued Wiring Diagrams Wiring SmartSwitch Output: Overview SmartSwitch Example: Wiring two non-SWM-compatible receiver/DVR groups and one SWMcompatible receiver/DVR group
PORT/A ANTENNA INPUT
18V
13V 18V/22KHZ 13V/22KHZ MULTISWITCH OUT 1
13V
18V/22KHZ 13V/22KHZ
Multiswitch Out 1
Region/Service Provider #1
STARBOARD/B ANTENNA INPUT TO ACU
18V
18V
18V
32-Output Multiswitch*
13V
18V/22KHZ 13V/22KHZ
18V/22KHZ 13V/22KHZ MULTISWITCH OUT 3
18V
Multiswitch Out 2
Region/Service Provider #2 Power Supply
13V
MULTISWITCH OUT 2
13V
18V/22KHZ 13V/22KHZ
Multiswitch Out 3
DIRECTV SWM Hardware Power Supply
16-Tuner SWM Expander**
32-Output Multiswitch*
Power to SWM
SWM-E2
GND
24 VDC IN +
18V
Non-SWM Receivers/DVRs (Linear, DIRECTV Latin America, DISH Network®, Bell TV, and legacy DIRECTV receivers)
13V 18V/22kHz Sat 99°/101° Sat 103°/110°/119°
Flex 13V/22kHz Sat 103°/110°/119° Port 1
Flex Port 2
Non-SWM Receivers/DVRs (Linear, DIRECTV Latin America, DISH Network, Bell TV, and legacy DIRECTV receivers)
SWM Power Inserter
SWM Power Inserter
8-Way Splitter
SWM Receivers/DVRs 8-Way Splitter
SWM Receivers/DVRs *NOTE: Similar connections apply to 16-output and 8-output multiswitches **NOTE: Similar connections apply to 32-tuner SWM expanders
11
A Continued Wiring Diagrams Wiring SmartSwitch Output: 32 Non-SWM-compatible Tuners SmartSwitch PORT/A ANTENNA INPUT
STARBOARD/B ANTENNA INPUT TO ACU
18V
18V
13V 18V/22KHZ 13V/22KHZ MULTISWITCH OUT 1
13V
18V/22KHZ 13V/22KHZ
18V 13V
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ MULTISWITCH OUT 3
13V
18V/22KHZ 13V/22KHZ
13V/ 22KHz
18V/ 22KHz
18V/ 13V/ 13V 22KHz 22KHz
18V
32-Output Multiswitch NOTE: Connections shown on this multiswitch also apply to 16-output and 8-output multiswitches
Additional Receivers/DVRs Receiver Satellite In TV/ANTENNA/ CABLE IN SATELLITE IN
12
R AUDIO
L
VIDEO
ETHERNET DIGITAL AUDIO OUTPUT
TV SET OUT Pb
Pr
Y
S-VIDEO
USB
PHONE
Power Supply
A Continued Wiring Diagrams Wiring SmartSwitch Output: 16 SWM-compatible Tuners and 32 Non-SWM-compatible Tuners 16-Tuner SWM Expander SWM1/PWR SWM1/PWR
Legacy 1
Optional - To SWM Power Inserter/8-Way Splitter
Legacy 2
24 VDC IN +
Power to SWM
Refer to the instructions in the SWM Expander Kit for complete wiring information
GND
SWM-E2
18V
Input
18V 13V Splitter
Flex Port 2
Splitter
Out
Out
13V/ 22KHz
18V/ 22KHz
Out
SmartSwitch PORT/A ANTENNA INPUT
STARBOARD/B ANTENNA INPUT TO ACU
18V
18V
13V 18V/22KHZ 13V/22KHZ MULTISWITCH OUT 1
13V
18V 13V
18V
18V/22KHZ 13V/22KHZ
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ MULTISWITCH OUT 3
13V
18V/22KHZ 13V/22KHZ
13V/ 22KHz 18V/ 22KHz
18V/ 13V/ 13V 22KHz 22KHz
SWM
IRD
SWM Power Inserter Power Supply Vessel AC Power
32-Output Multiswitch NOTE: Connections shown on this multiswitch also apply to 16-output and 8-output multiswitches
8-Way Splitter
Non-SWM Receivers/DVRs (Linear, DIRECTV Latin America, DISH Network, Bell TV, and legacy DIRECTV receivers)
Satellite In DIRECTV (SWM-1) SWM Receiver COMPONENT OUT
SATELLITE IN (SWM-1)
S-VIDEO OUT USB
VIDEO OUT
Out
Flex 13V/22kHz Sat 103°/110°/119° Port 1
13V 18V/22kHz Sat 99°/101° Sat 103°/110°/119°
Input
DIGITAL AUDIO OUT OPTICAL
AUDIO OUT
ETHERNET
PHONE JACK
HDMI OUT
Supports up to 7 Additional Tuners Each SWM Receiver = 1 Tuner Each DVR = 2 Tuners
13
A Continued Wiring Diagrams Wiring SmartSwitch Output: 32 SWM-compatible Tuners and 32 Non-SWM-compatible Tuners 32-Tuner SWM Expander SWM1/PWR SWM1/PWR
Legacy 1
Optional - To SWM Power Inserter/8-Way Splitter
Legacy 2 Optional - To SWM Power Inserter/8-Way Splitter 24 VDC IN +
Refer to the instructions in the SWM Expander Kit for complete wiring information
24 VDC IN +
Power to SWM
Power to SWM
GND
SWM-E4 18V
Flex 13V/22kHz Sat 103°/110°/119° Port 1
13V 18V/22kHz Sat 99°/101° Sat 103°/110°/119°
18V 13V
Flex Port 2
13V/ 22KHz
Optional - To SWM Power Inserter/8-Way Splitter
18V/ 22KHz
Legacy 2 Legacy 1
SWM1/PWR SWM1/PWR
SmartSwitch PORT/A ANTENNA INPUT
STARBOARD/B ANTENNA INPUT TO ACU
18V
18V
13V 18V/22KHZ 13V/22KHZ MULTISWITCH OUT 1
13V
18V 13V
18V
18V/22KHZ 13V/22KHZ
18V
13V
MULTISWITCH OUT 2
18V
13V
18V/22KHZ 13V/22KHZ
18V
18V/22KHZ 13V/22KHZ MULTISWITCH OUT 3
13V
18V/22KHZ 13V/22KHZ
13V/ 22KHz 18V/ 22KHz
18V/ 13V/ 13V 22KHz 22KHz
SWM
IRD
SWM Power Inserter Power Supply Vessel AC Power
32-Output Multiswitch NOTE: Connections shown on this multiswitch also apply to 16-output and 8-output multiswitches
8-Way Splitter
COMPONENT OUT
SATELLITE IN (SWM-1)
S-VIDEO OUT USB
VIDEO OUT
Non-SWM Receivers/DVRs (Linear, DIRECTV Latin America, DISH Network, Bell TV, and legacy DIRECTV receivers)
Satellite In DIRECTV (SWM-1) SWM Receiver DIGITAL AUDIO OUT OPTICAL
AUDIO OUT
HDMI OUT
Supports up to 7 Additional Tuners Each SWM Receiver = 1 Tuner Each DVR = 2 Tuners
14
ETHERNET
PHONE JACK
