Transcript
Network Camera SNC-HM662 Edge Storage Manual — Record and Playback Video with SD / microSD —
Table of Contents 1. Edge Storage Function 1-1. What is the Edge Storage function 1-2. Precautions when using the Edge Storage function 1-3. Usable memory card
2. Recommended Setting when Using the Edge Storage Function 3. How to Use Edge Storage 3-1. Initialization of memory card 3-2. Time setting of the camera 3-3. Recording setting of Edge Storage (constant recording) 3-4. Recording setting of Edge Storage (sensor input) 3-5. Recording setting of Edge Storage (compound condition)
4. Playback, Saving, and Deleting of Recorded Video
1. Edge Storage Function 1-1. What is the Edge Storage function This is a function to record the video and audio on the microSD memory card installed on the memory card slot of the camera by the alarm detection result such as network disconnection, etc. Refer to the Installation Manual accompanying the camera for installing of the memory card to the camera.
1-2. Precautions when using the Edge Storage function
Insertion and replacement of the memory card should be performed when the power of the camera is turned off. Also, always stop the recording of Edge Storage before turning off the power of the camera.
Stop the recording of Edge Storage when turning off the power of the camera when the memory card is inserted.
Initialize (format) the memory card before using a memory card.
It may take some time to search or display when there are more than 500 videos recorded on the memory card.
It may take some time for the playback to start when the volume of the recorded video file is large.
New recording will be stopped when the recording volume has reached close to the maximum when [Enable cyclic storage] is not selected. Recording will be overwritten from the oldest one when [Enable cyclic storage] is selected.
The video or audio may be interrupted duet to recording data becoming very large depending on the setting of the video codec. Confirm the video codec setting and environment before operation.
The frame rate for the monitor image of the viewer and the operability may decrease when recording video or still picture.
Interval of the still pictures actually being recorded may become longer than what is set.
We assume no responsibility for any damage caused by destruction of record data, etc.
Memory card has a limited life span. It may not record correctly when used for a long period of time, so please replace with a new memory card for such a case.
Memory card has a limited life span and usage, and constant recording affects the life span of memory card more than the event recording, so it is recommended to operate with event recording.
1-3. Usable memory card Use the microSDHC card that is CLASS 10 and compatible with operation guarantee temperature of 85 degrees Celsius or higher when recording with the Edge Storage function. The recording may not be performed correctly when microSDHC card not compatible with this condition is used. This does not guarantee the operation of all the microSDHC cards compatible to this condition. Operation of this network camera is confirmed with the SanDisk Extreme Series microSD memory card.
1
2. Recommended Setting when Using the Edge Storage Function It is required to take caution on the setting for the video codec, etc., so the camera performance will not affect the recorded video when using the Edge Storage function. The following table is a guide for setting the video codec so the camera performance will not affect the recorded video. However, it still may affect the recorded video even if it is the recommended setting depending on the installed environment of the camera or the condition of the usage, so perform sufficient test before starting the operation. Reduce the image size or increase the frame rate or the bit rate to record for long hours.
[Recommended setting]
Recommended setting Video 1
Video 2
Video 3
H.264
H.264
H.264
2560 x 1920
640 x 480
640 x 480
1 picture interval
1 sec
5 sec
5 sec
Frame rate
10 fps
1 fps
1 fps
Bit rate
3 Mbps
128 kbps
128 kbps
Codec Image size
*
Recording target
2
[Recordable time]
*
Recording time when the overwrite setting is turned off and performing constant recording.
*
Recording time will differ depending on the used memory card or recording environment.
Audio codec: AAC 128Kbps Setting
Rough indication of recordable time
Video
Size
Frame
Bit
Codec
[pixel]
rate
rate
[fps]
[bps]
4GB
8GB
16GB
32GB
H.264
2560 x 1920
10
3M
3 hours
6 hours
12 hours
24 hours
H.264
2560 x 1920
5
1M
8 hours
16 hours
1.3 days
2.6 days
H.264
1600 x 1200
5
512k
14 hours
1.2 days
2.3 days
4.6 days
H.264
640 x 480
5
256k
22 hours
1.9 days
3.8 days
7.5 days
Audio codec: G.711 Setting
Rough indication of recordable time
Video
Size
Frame
Bit
Codec
[pixel]
rate
rate
[fps]
[bps]
4GB
8GB
16GB
32GB
H.264
2560 x 1920
10
3M
3 hours
6 hours
12 hours
24 hours
H.264
2560 x 1920
5
1M
8 hours
17 hours
1.4 days
2.9 days
H.264
1600 x 1200
5
512k
16 hours
1.3 days
2.6 days
5.3 days
H.264
640 x 480
5
256k
1.2 days
2.4 days
4.7 days
9.5 days
Audio codec: OFF Setting
Rough indication of recordable time
Video
Size
Frame
Bit
Codec
[pixel]
rate
rate
[fps]
[bps]
4GB
8GB
16GB
32GB
H.264
2560 x 1920
10
3M
3 hours
6 hours
12 hours
24 hours
H.264
2560 x 1920
5
1M
9 hours
18 hours
1.5 days
3 days
H.264
1600 x 1200
5
512k
18 hours
1.5 days
3 days
6 days
H.264
640 x 480
5
256k
1.5 days
3 days
5.9 days
11.9 days
3
3. How to Use Edge Storage There are 2 types of the Edge Storage function, the constant recording that will constantly record in the memory card, and the event recording that will record based on the schedule of the camera or the trigger input. Memory card has a limited life span and usage with constant recording affects the life span of memory card more than the event recording, so it is recommended to operate with event recording.
3-1.
Initialization of memory card Click [Format SD memory card] in [SD memory card] under [Edge storage].
4
3-2. Time setting of the camera 1.
When synchronizing with the clock in the computer Set the time setting in [Date & time] under [System] to [Synchronize with PC], select an appropriate time zone for [Time zone], and click [OK].
2.
When setting manually Set the time setting in [Date & time] under [System] to [Manual setting], select an appropriate date/time, and click [OK].
5
3-3. Recording setting of Edge Storage (constant recording) 1.
2.
Open [Video Codec] under [Video / Audio].
Set each setting item in accordance with the recommended setting in Section 2 and click [OK]. At this time, set the settings for [Image 2] and [Image 3] in accordance with the recommended setting.
3.
If writing with an overwrite setting when recording to the SD card, open [SD memory card] under [Edge storage], select [Enable cyclic storage] in [SD card control], and click [OK].
6
4.
Open [SD memory card] under [Edge storage], and confirm that [Status] under [SD memory card] is [Ready].
5.
Open the [Recording Settings] menu under [Recording] and click [Add].
7
(1) Input the recording name (2) Confirm that the days of week in [Trigger] are selected and [Time] is set to [Always].
(3) Click [2. Destination] and input the setting of the recording file management. Click [OK] and then click [Close].
8
6.
A setting for the constant recording is added in the [Recording Settings] menu under [Recording]. The recording will start by clicking [OFF] under [Status] and changing it to [ON].
9
3-4. Recording setting of Edge Storage (sensor input) This is a setting procedure to record when there is a sensor input.
1.
2.
Open [Video Codec] under [Video / Audio].
Set each setting item in accordance with the recommended setting in Section 2 and click [OK]. At this time, set the settings for [Image 2] and [Image 3] in accordance with the recommended setting.
3.
Open [SD memory card] under [Edge storage], and confirm that [Status] under [SD memory card] is [Ready].
10
4.
Click [Add] in [Event settings] under [Event].
5.
Click [1. Schedule] in the Event setting screen. Select and check the days of week. Also, select [Always] for [Time], or enter the start time in [From] and the end time in [to].
11
6.
Click [2. Trigger] in the Event setting screen. Select [Sensor input], and select the detection condition from [Active], [Normal to Active], or [Active to Normal].
7.
Click [3. Action] in the Event setting screen. Click [Add file format].
12
8.
Input [Setting name] and select [Video clip]. Select [Image 1], input [Pre-event recording], [Maximum duration], [Maximum file size], and [File name prefix], click [OK] and then click [Close].
(Note) The recording will finish when the recording has reached the maximum duration or the maximum file size that is set.
9.
Select [Edge storage] under [Action] and select [Sensor Input Detect] under [File format].
13
10. Enter a name in [Event name] and select [Enable this event]. Enter a value in [Detect next motion detection or digital input after ... second(s).]. Click [OK] and then click [Close].
11. A setting was added under [Event] and [File format] in [Event settings]. Now, a recording will be made when there is a sensor input.
14
4. Playback, Saving, and Deleting of Recorded Video Playback, saving, and deleting of the recorded video on the memory card is performed in the [Content management] screen under [Edge storage]...
1. A list of the recorded recording data is displayed by clicking on [Refresh].
15
2. Only the corresponding files will be displayed by entering character strings regarding trigger time, file format, or trigger type in [Search].
3. Select the file from the list, and the selected video is played back by clicking on the [View] button.
4. To save the recorded video, select the file from the list, and perform download by clicking on the [Download] button.
16
5. To delete the recorded video, place a check mark in the box at the left of the list and click [Delete].
6. If you do not want to delete the recorded video by mistake, place a check mark in the box at the left of the list, click [Lock/Unlock], and the specified file will be locked and the [Locked] item will change to [Yes]. To release the lock, click [Lock/Unlock] again.
17
