Software And Pelco Video Compatibility Matrix

Transcript

Software and Pelco Video Compatibility Matrix Andover Continuum 1 Versions 1.7 through 1.9 Date: September 2015 The products listed in the chart below and on the next page are the only video products that can be integrated using Andover Continuum’s video features. Products not listed are not supported in Andover Continuum video features. The Pelco component versions listed in this document are the tested and supported revisions per Andover Continuum software version. CyberStation / web.Client Software Version VideoMon1 Add-on software 1.7x/1.8 1.81 Video Layouts2 Video Layouts2 1.82 Video Layouts2 1.9 Video Monitor3 Video Layouts2 Video Monitor3 Pelco Video Management System DVX9 v3.1 v3.1 v3.1 v3.1 v3.1 v3.1 DVXi v4.3.1.90 v4.3.1.90 v4.3.1.90 v4.3.1.90 v4.3.1.90 v4.3.1.90 • DS RealVue v4.2 v4.2 v4.2 v4.2 • DS NVR/NVS v4.2 v4.2 v4.2 v4.2 • DS Enterprise v4.2 v4.2 • DS VAU v4.2 v4.2 9 Digital Sentry • DS4U • DS SRV Endura v1.x5 Endura v2.05 Cameras n IP Cameras Sarix Cameras n 6 Andover Continuum Incoming Video System Alarms7 Intrinsic Alarms n 7 n n n Alarming using controller objects7 or n = supported in Andover Continuum software = available as an add-on software = not supported Note: Viewing video via the Andover Continuum software interfaces requires different/additional machine resources than workstations and machines that do not use video functionality. Refer to the corresponding Andover Continuum software installation guides for each version (e.g. v1.92, v1.93) for hardware and software requirements to properly support video functionality. The information on these charts is furnished for informational purposes only, is subject to change without notice, and should not be construed as a commitment by Schneider Electric. 1. VideoMon Add-On software is not part of the core Andover Continuum software; it is add-on software supported by the SEBB Americas region (not PSS). 5. Endura support requires a paid add-on option to CyberStation (per workstation) and web.Client (per server). 2. Video Layouts functionality is supported both on CyberStation workstations and web.Client browsers. 6. Sarix cameras should be configured to use stream 2 at lower resolutions for best machine performance. 3. Video Monitor (and Video Administrator used to configure it) is a paid add-on option (in v1.82) to CyberStation (per workstation) and is not supported on web.Client. 7. Only the following video alarms are supported: 1) video server online/offline, 2) camera video loss, and 3) motion detection (per camera). 4. Video Monitor (and Video Administrator used to configure it) is a standard feature in CyberStation (as of v1.9) and is not supported on web.Client. 8. DVX and DVXi do not support video loss and motion alarm functionality. PA-00210 Andover Continuum and Pelco Video Compatibility Matrix 9.Obsolete Pelco Products 2 Software and Pelco Video Compatibility Matrix Andover Continuum Versions 1.91 through 2.0 CyberStation / web.Client Software Version 1.91 with DSConneX Patch 1.91 Video Layouts2 Video Monitor4 Video Layouts2 DVX9 v3.1 v3.1 v3.1 v3.1 DVXi v4.3.1.90 v4.3.1.90 v4.3.1.90 • DS RealVue v4.2 v4.2 • DS NVR/NVS v4.2 • DS Enterprise 1.92/.93 Video Monitor4 Video Layouts2 1.94 2.0 Video Monitor4 Video Layouts2 Video Monitor4 Video Layouts2 Video Monitor4 v3.1 v3.1 v3.1 v3.1 v3.1 v3.1 v4.3.1.90 v4.3.1.90 v4.3.1.90 v4.3.1.90 v4.3.1.90 v4.3.1.90 v4.3.1.90 v4.2,v7.0 v4.2,v7.0 v4.2,v7.0, v7.1 v4.2,v7.0, v7.1 v7.2.30 v7.2.30 v7.2.30 v7.2.30 v4.2 v4.2,v7.0 v4.2,v7.0 v4.2,v7.0, v7.1 v4.2,v7.0, v7.1 v7.2.30 v7.2.30 v7.2.30 v7.2.30 v4.2 v4.2 v4.2,v7.0 v4.2,v7.0 v4.2,v7.0, v7.1 v4.2,v7.0, v7.1 v7.2.30 v7.2.30 v7.2.30 v7.2.30 • DS VAU v4.2 v4.2 v4.2,v7.0 v4.2,v7.0 v4.2,v7.0, v7.1 v4.2,v7.0, v7.1 v7.2.30 v7.2.30 v7.2.30 v7.2.30 • DS4U v4.2 v4.2 v4.2,v7.0 v4.2,v7.0 v4.2,v7.0, v7.1 v4.2,v7.0, v7.1 v7.3.54 v7.3.54 v7.3.54 v7.3.54 v7.3.54.7.4.149 v7.7.309.9631 See pg.3 See pg.3 See pg.3 See pg.3 See pg.3 See pg.3 See pg.3 See pg.3 n n n 1.6.13.xxxx 1.6 and 1.7 1.6 and 1.7 Pelco Video Management System 9 Digital Sentry • DS SRV Endura v1.x5 See pg.3 See pg.3 Endura v2.0 See pg.3 See pg.3 5 Cameras n IP Cameras n Sarix Cameras6 Andover Continuum Incoming Video System Alarms7 Intrinsic Alarms7 n n Alarming using controller objects7 or n = supported in Andover Continuum software n n n n n n = available as an add-on software = not supported Note: Viewing video via the Andover Continuum software interfaces requires different/additional machine resources than workstations and machines that do not use video functionality. Refer to the corresponding Andover Continuum software installation guides for each version (e.g. v1.92, v1.93) for hardware and software requirements to properly support video functionality. The information on these charts is furnished for informational purposes only, is subject to change without notice, and should not be construed as a commitment by Schneider Electric. 1. VideoMon Add-On software is not part of the core Andover Continuum software; it is add-on software supported by the SEBB Americas region (not PSS). 5. Endura support requires a paid add-on option to CyberStation (per workstation) and web.Client (per server). 2. Video Layouts functionality is supported both on CyberStation workstations and web.Client browsers. 6. Sarix cameras should be configured to use stream 2 at lower resolutions for best machine performance. 3. Video Monitor (and Video Administrator used to configure it) is a paid add-on option (in v1.82) to CyberStation (per workstation) and is not supported on web.Client. 7. Only the following video alarms are supported: 1) video server online/offline, 2) camera video loss, and 3) motion detection (per camera). 4. Video Monitor (and Video Administrator used to configure it) is a standard feature in CyberStation (as of v1.9) and is not supported on web.Client. 8. DVX and DVXi do not support video loss and motion alarm functionality. PA-00210 Andover Continuum and Pelco Video Compatibility Matrix 9.Obsolete Pelco Products 3 Andover Continuum Andover Continuum Video Interfaces Supported Video Formats Video Layouts Pelco Video Management System Supported video formats Digital Sentry MJPG, MPEG4, H.264 Endura MPEG4, H.264 Cameras Tested version with Andover Continuum v1.92 & v1.93 Tested version with Andover Continuum v1.94 IP 3701 camera 1.00.0026 1.02.0015 Spectra IV IP Camera 1.01.0052 1.02.0015 Introduced in v1.7, allow users to view live video and search (and view) recorded video in a matrix format (up to a 3x3 matrix). Video Layouts can be launched to display live video upon an alarm event. Note: Video Layouts are supported in CyberStation machines and in web.Client browsers. Video Monitor Introduced in v1.82, allows users to simultaneously view live and recorded video associated with Andover Continuum points (e.g. doors, outputs) upon an alarm event. Up to 16 cameras can be assigned to each object; only one camera can be viewed at a time. Note: Video Monitor (& Video Administrator used to configure it) is not supported in web.Client; it is only supported on CyberStation workstations. Viewing video through a web page is possible but is not a core feature of Andover Continuum software. HTM file samples (for particular software version) are available on the Buildings Business Extranet Global website. Sarix Cameras Refer to the list of the tested Sarix Cameras below. Browse to Products -> Andover Continuum -> Software -> Sample HTM page for Video. General Because Pelco Digital Sentry and Endura are different systems with different integration methods, some video functionality with Andover Continuum may vary between systems. Pelco video system versions must be successfully tested with Andover Continuum versions for video integration support. • Pelco release of a new version does not automatically ensure compatibility with Andover Continuum; it must be formally tested by Andover Continuum 1.6.13.xxxx Sarix camera models Software version tested for v1.91 Software version tested for v2.0 IXE10C 1.7.41.9081 1.9.2.20 IXE10DN 1.74.9081 1.9.2.20 IM10DN10 1.7.41.8263 1.9.2.20 IMS0LW10 1.8.1.8270 1.9.2.11 IEE10N 1.7.41.8111 1.9.2.19 IXS0LW 1.8.1.9083 1.9.2.20 IX30C 1.7.41.9080 1.9.2.20 Spectra IV IP 1.02.0015 1.00.0034 Spectra IV IP H.264 1.7.41.2084 1.9.2.12 IP110 1.02.0015 1.02.0018 IP3701 1.02.0015 1.02.0018 SureVision Model # IMS0LW10-IE 1.9.2.20 1.9.2.20 IXS 0C 1.9.2.11 1.9.2.11 Sarix cameras For Pelco Endura, Andover Continuum defaults to stream 2 for video. If stream 2 is not available, then Andover Continuum will revert to stream 1. However, note this does impact machine resources. Refer to the Andover Continuum software installation guides for machine requirements per revision. Cameras Tested Analog, IP (including Sarix cameras) were tested through both Digital Sentry and Endura systems to verify compatibility with Andover Continuum. The following table includes the sample IP and Sarix cameras tested (including revision). Note: Only Andover Continuum software v1.92 and greater support Sarix cameras. PA-00210 Andover Continuum and Pelco Video Compatibility Matrix 4 Andover Continuum Compatible Endura components (including versions) per Andover Continuum software revision: Specific versions of Pelco Endura components have been tested for compatibility Andover Continuum software. The following versions (for the products below) are required for compatibility per Andover Continuum software revision: CyberStation / web.Client Software Version v1.91 v1.92 / v1.93 v1.94 v2.0 SM 5200 System Manager - - 1.0.0.0847 1.5.0.0063 SM5000 System Manager 1.04.0027 1.04.0036 1.4.69.492 1.4.69.492 WS5000 1.05.0046 2.03.00.9084 2.05.03.10245 2.05.09.11053 Pelco Endura Component WS5070 - - 2.05.03.10245 2.05.03.10245 2.00.01.xxxx 2.1.3.0120 2.1.5.0001 2.04.00.0045 NET5301T single channel encoder 1.03.1054 1.03.2061 1.03.2061 1.03.2063 NET53XX 8/16 channel encoder 1.4.0419 1.4.0041 1.4.0041 1.4.0041 DVR5100 1.04.3044 1.05.3035 1.05.3035 1.05.3035 DVR5300 1.04.4014 1.04.4014 1.04.4014 1.04.4014 NSM5200 ENC5316 encoder (for DVR5300) 1.4.0412 1.4.0421 1.4.0421 1.4.0421 NVR5100 1.04.4014 1.04.4109 2.13.0120 2.13.0120 Endura Express - 1.01.00.0051 1.01.01.0004 1.02.00.0137 UDI5000 - 1.0.2.0005 1.0.2.0307 1.4.0.0021 Note: Only Endura-enabled components are compatible with Andover Continuum software – e.g. the DVR5100 must be Endura-enabled to be supported. You may need to upgrade the software in your Pelco devices for successful integration with Andover Continuum. Software upgrades are available from Pelco. All brand names, trademarks and registered trademarks are the property of their respective owners. Information contained within this document is subject to change without notice. Schneider Electric Jägershillgatan 213 75 Malmö, Sweden Telephone: +46 (40) 38 68 50 PA-00210 Andover Continuum and Pelco Video Compatibility Matrix www.schneider-electric.com September 2015 © 2014-2015 Schneider Electric. All rights reserved. The information on these charts is furnished for informational purposes only, is subject to change without notice, and should not be construed as a commitment by Schneider Electric.