Soldering Iron

Transcript

Soldering iron • • • High-performance soldering iron that, in the pursuit both "usability" and "appearance", has evolved beyond being a mere working tool Compact design has drastically reduced footprint Use of special driver (possible to be stored in the main unit) for thermal correction reduces the load on a temperature control knob Model No. Unit Color Iron Holder Color Packing List No.FX888 Blue-Yellow Blue-Yellow Model No. FX888 Power consumption 70W Temperature range 200-480ºC Temperature stability ±1ºC at idle temperature ・Station Output voltage 26V Dimensions 100(W)×120(H)×130(D)mm 1.3kg Weight Soldering station (FX-888), Soldering iron (FX-8801 with soldering tip type B), Iron holder (with cleaning wire, cleaning sponge and rubber cleaner), Hexagon wrench, CAL adjustment driver, Instruction Manual ・Soldering Iron Power consumption 65W (26V) Tip to ground resistance <2Ω Tip to ground potential <2mV Shape-B (No.T18-B) Standard tip Ceramic heater Heating element 1.2m Length of cord 217mm (with B tip) Total length 46g (with B tip) Weight * Length and weight (w/o cord) Full design changes for HAKKO 936 High-performance soldering iron pursuing "usability" and "appearance" has evolved into more than a mere working tool. Temperature controller achieves 3 factors such as "space saving", "good maintainability" and "good safety and stability" ·Footprint was reduced by approx. 50% compared to that of conventional HAKKO 936. ·Use of special driver (resin) for thermal correction during daily inspection maintains durability. ·The temperature control knob can be locked to prevent the setting temperature from changing during the work. How to lock the temperature control knob Soldering iron provides 30% increase in workability compared to that of conventional HAKKO 936. ·Improved thermal conductivity enables the same work to be performed in a shorter time. (Refer to the workability comparison graph.) ·The rise time is 20 seconds faster and drop in tip temperature during work is reduced. (Refer to the thermal characteristics graph.) Workability comparison graph Thermal characteristics graph The internal structure and tip shape were reviewed to provide better thermal conductivity and better thermal efficiency. As a result, the time for performing the same work was greatly shortened. It was demonstrated that the rise time is approx. 20 seconds faster, and the drop in tip temperature during continuous work is reduced. ·Employment of separated-heater tip achieves low running cost. ·Making the element cover thinner enables better viewing during work and easier working even on a P.W.B. with highly dense components. Iron holder provides 3 cleaning methods and low-noise effect ·Sound and vibration generated when placing the iron into the iron holder were reduced by 30%. ·Three types of cleaning methods are available in one iron holder using a cleaning sponge, cleaning wire and rubber cleaner. ·The detachable waste holder at the bottom of iron holder offers an easy way to dispose of the waste. · Ultra-compact size with consideration of environment and ease of use Space-saving design leaves working area large even in a cell-production site. * The conventional product shown in the photo is HAKKO 936. HAKKO FX-8802 N2 (nitrogen) gas system A space-saving N2 system. Anti-oxidation and pre-heating significantly improve solderability. —Example Configuration (N2 System) Soldering station, Iron holder, N2 gas generator, and N2 flowmeter must be purchased separately. HAKKO FX-8803 One-hand, manual-solder-feed iron — Example Configuration (One-hand, Manual-Solder-Feed System) Soldering station and Iron holder must be purchased separately. HAKKO FX-8804 Hot tweezers —Example Configuration (Hot Tweezer System) Soldering station, cap, and Iron holder must be purchased separately. Tips for using HAKKO FX-888. 1. How to remove the bottom plate. 1. Press the slide lock button inward. Note Press it firmly from upward. It is easy to open by the slide lock sloping inward. 2. Open the iron holder base while pressing the slide lock. 3. Remove the solder waste in the bottom plate. 2. How to lock the temperature control knob The temperature control knob can be locked to prevent the setting temperature from changing during the work. In case of locking it, please insert the hexagon wrench into the lower hole and tighten the hexagon screw in the hole counterclockwise. As for unlocking, don't touch the upper hole. Adjust by the upper hole makes the control knob loosen. T18 Series Shape BC/C This type has a shape like a cone or column cut at a slant, which allows users to select the cut surface size depending on the workpiece. It is used for drag soldering and pre-tinning of lead wires. T18-C05 Shape-0.5C • • • • T18-C08 Shape-0.8C T18-C1 Shape-1C T18-C2 Shape-2C T18-C3 Shape-3C • • • • • • • T18-C4 Shape-4C T18-C5 Shape-5C NEW T18-CF1 Shape-1CF Tinned cut surface only T18-CF15 Shape-1.5CF Tinned cut surface only T18-CF2 Shape-2CF Tinned cut surface only T18-CF3 Shape-3CF Tinned cut surface only T18-CF4 Shape-4CF Tinned cut surface only • • T18-CSF25 Shape-2.5CSF This type has good heat transfer with short tip end design, tinned cut surface ony. T18-S6 Shape-S6 NEW Shape B All-round type which can be used from any direction and is easy to hold at any position. Possible to solder any surface from small to large. • • • • T18-B Shape-B T18-BL Shape-BL NEW T18-S4 Shape-S4 NEW T18-SB Shape-SB Shape D This type has a shape like a flat-blade screwdriver and is capable of soldering by applying the tip in 2 ways: line and face. The width (size of tip) suitable for the workpiece can be selected, and it can be used for any soldering work. • • • • • • T18-D08 Shape-0.8D T18-D12 Shape-1.2D T18-D16 Shape-1.6D T18-D24 Shape-2.4D T18-D32 Shape-3.2D T18-DL12 Shape-1.2DL NEW • • • • T18-DL2 Shape-2DL NEW T18-DL32 Shape-3.2DL NEW T18-S3 Shape-S3 NEW T18-S9 Shape-S9 NEW Shape I This type has a thin conical end and is an ultrafine tip which is best suited for soldering at narrow pitches, etc. It is the best for soldering micro components such as 0603, etc. and for repairing high-densitymounting P.W.Bs. such as in cellular phones, etc. • T18-I Shape-I Shape J This type differs from Shape B and I by bending the tip end and is capable of soldering by applying the tip in 2 ways: face and point. It is used for drag soldering and correction of bridging. • T18-BR02 Shape-0.2BR NEW Shape K This type has a shape like a knife and is capable of soldering by applying the tip in 3 ways: line, face and point. It is used for soldering at narrow pitches, correction of bridging and drag soldering. • T18-K Shape-K Part No. Name FH800-01SV Iron holder Specifications silver FX8801-01 Soldering iron FX-8801 65W (26V) B3466 CAL adjustment driver B2017 Hexagon wrench A1561 Cleaning wire B3474 Rubber cleaner A1560 Heating element B3469 Tip enclosure A1559 Cleaning sponge B1785 Nut B2022 Nipple 65W (26V)