Transcript
21.5 60
60
18
38
263
M5 282 300
W 1/4
170
139
75º
BC2003-BM
DOLPHIN BEHIND MIRROR HAND DRYER › High speed low energy hand dryer
HEIGHT
170
MM
› Dries hands in 13 seconds reducing the CO2 emissions
WIDTH
282
MM
PROJECTION
139
MM
› Rated power: 1,000w, 6.5A › Operating power of only 1,000w (500w heating element) – saving 80% of user’s energy costs
PLEASE NOTE: We strongly recommend that the surfaces beneath and to either side of this dryer allow regular cleaning
› Infra-red, self adjusting sensor
(such as smooth cleanable paint, tile, Perspex, stainless steel
› Sound level of 75db at 1 metre
etc) to prevent staining from the water blown from users
› IP14 rated
hands. New generation high speed dryers such as this are designed to blow the water off the hands so consideration
› Class 1 rated isolation
like this needs to be given to deal with the water deposits.
› Dryer delivers 101.7m3/hour (90m/s). › 29,000 rpm brush motor › 55ºC air output temperature › Three year limited warranty › Also available with base plate system to allow interchange with BC9288BM hand towel dispenser › To special order we can supply a special mounting plate that allows this dryer to be interchangeable with our BC9288BM paper towel dispenser at a later date
High speed with element on Low speed with element on High speed with element off Low speed with element off
Motor Heater Total (wattage) (wattage) wattage 450 450 900W 225 225 450W 450 0 450W 225 0 225W
Sound Level 75.1dB 68.2dB 75.1dB 68.2dB
TECHNIC AL HELPLINE 01424 202224 DOLPHINSOLUTIONS.CO.UK
60
60
21.5
8.5
139
88.5
1000
47
38
170
Ø5.2
°
75
18
M5 282
83.5
300
118.91
263
W1/4
BELL-CHEM PRODUCTS COMPANY DOLPHIN VELOCITY HIGH SPEED LOW ENERGY BEHIND MIRROR HAND DRYER 1000W BC 2003BM
BC2003BM
DOLPHIN BEHIND MIRROR HIGH SPEED HAND DRYER T H R E E Y E A R WA R R A N T I E S
BC2 0 0 3 DOLPHIN HAN D D RYE R
Dolphin Hand Dryer 3 Year Limited Warranty • Year 1: full repair service (parts and labour) • Years 2-3: parts only warranty (labour not included) • Beyond year 3: replacement parts are available through our parts supply service. 1. 1.1 1.2
1.3
1.4 1.5
1.6
1.7
2. 2.1
WARRANTY TERMS AND CONDITIONS The Warranty becomes effective at the date of purchase (or the date of delivery if this is later). In the event of a Warranty claim, you must provide the hand dryer serial number and proof of delivery and/or purchase before any work is carried out. Without this proof, any work carried out will be chargeable. In the event of a Warranty claim, we must be given the opportunity to inspect the product, should we request to do so. Additionally, we may request photographic evidence. The repair or replacement of your product under warranty will not extend the period of Warranty. The product must have been installed, used and cared for in accordance with our instructions for care and maintenance. Where our on-site investigation reveals that the reported fault is not due to a manufacturing or material defect, a call out charge may be applied. The Warranty provides benefits which are additional to, and do not affect your statutory rights as a consumer. WHAT IS COVERED BY THE WARRANTY? In the first year, the repair or replacement of your Dolphin Hand Dryer, if it is found to be defective due to faulty materials, workmanship or function within the Warranty period. 2.1.1 The decision to repair or replace your product is at the sole discretion of BellChem Products Ltd. If any part is no longer available or out of manufacture, Bell-Chem Products Ltd will replace it with a functional replacement part. 2.1.2 In the event that repair or replacement is not feasible, the original purchase price will be refunded.
BC2003BM User Manual
2.2
In years 2-3, the replacement of failed parts1. Labour is not included. The most appropriate option of the following will be undertaken, dependent upon the circumstances. • provision of spare parts – cost free. • on-site support/repair – labour chargeable. • return to us for repair – labour chargeable. • replacement with a reconditioned unit.
3.
WHAT IS NOT COVERED BY THE WARRANTY? Normal wear and tear.
3.1
Note: Motor brushes are subject to normal wear and tear through usage.These parts are covered under the Warranty for 2 years from date of purchase (labour not included). Thereafter, replacement parts are available through our parts supply service.
3.2
3.3 3.4
3.5
3.6
3.7 1
Faults caused by misuse, modification, misapplication, neglect or wilful or accidental damage. Faults caused by incorrect installation. Faults caused by incorrect voltages or installation in areas that require a higher IP rating than offered by the dryer. Repairs or alterations carried out by parties other than Bell-Chem Products Ltd or its authorised agents. Damage or malfunction caused by inappropriate cleaning, or lack of necessary cleaning. (Please refer to our instruction manual for guidance.) Consequential damages of losses
Exceptions apply – see clause 3.1
www.dolphinsolutions.co.uk
BC 2003 Hand Dryer Range – parts diagram 'LDJUDP
BC2003BM User Manual
www.dolphinsolutions.co.uk
5HSDLUSDUWVOLVW .H\
'HVFULSWLRQ
.H\
(QFORVXUH &DVLQJ
'HVFULSWLRQ ,QVXODWLRQ0\ODU
6HFXULW\KH[VFUHZ UHTG
7HUPLQDOEORFN
%ORZHUKRXVLQJ8SSHU
%ORZHUPRXQWLQJEUDFNHW
%ORZHUKRXVLQJ%HORZ
6HQVRUEUDFNHW
0RWRU
6HQVRU
0RWRUUXEEHU8SSHU
&DEOHFODPS
0RWRUUXEEHU%HORZ
&DEOH3URWHFWRU
+HDWHUDVVHPEO\
*URXQGLQJ6FUHZ
&LUFXLW%RDUG0RGXOH
/HIWER[EUDFNHW
%DVHSODWH
5LJKWER[EUDFNHW
1\ORQKROHEXVKLQJ
%R[
Dolphin Solutions Ltd Southpoint, Compass Park, Junction Road Bodiam, TN32 5BS, United Kingdom T +44 (0)1424 202 224
[email protected] dolphinsolutions.co.uk © Dolphin Solutions Ltd
BC2003BM User Manual
www.dolphinsolutions.co.uk
DOLPHIN CE DECLARATION OF CONFORMANCE
We Dolphin Dispensers Southpoint, Compass Park, Bodiam Robertsbridge TN32 5BS
Declare under our sole reponsibility that the product Hand Dryer Brand: Dolphin BC2003BM Has been designed and manufactured in accordance with the following standards. Harmonised standard EMC EN55014 1:2006/A1:2009+A2:20111 EN61000-3-2 : 2014 EN61000-3-3 : 2013 EN55014-2:1997/A2:2008 Category II IEC61000-4-2:2008 IEC61000-4 -6:2013IEC61000-4-4:2012 IEC61000-4-11:2004 IEC61000-4-5:2014 LVD
EN60335-1:2012 & EN60335-2-23:2003 + A1:2008 + A11:2010
EMF
EN62233 : 2008
LVD DIRECTIVE 2006/95/EC EMC DIRECTIVE 2004/108/EC
February 22, 2016 England
BC2003BM
DOLPHIN BEHIND MIRROR HIGH SPEED HAND DRYER USER MANUAL
BC2 0 0 2 DOLPHIN HAN D D RYE R
High-Speed
Hand drier
BC2003BM
Operating Instructions and Parts Manual (Automatic) Surface Mount 139 mm
263 mm
170 mm
TECHNICAL SPECIFICATIONS PERFORMANCE DATA
ITEM CATEGORY
Operating Voltage
220-240Vac, 50/60Hz, 0.84-1.0kW
Warm Air Speed Output
90m/s, adjustable
Motor Type
250-500W, 29000r.p.m., Adjustable; Brush Type, Dual Ball Bearings
Motor Thermal Protection Heater Element Heater Thermal Protection Drying Time
Auto Resetting Thermostat turns unit off at 95°C {203°F} 500W, adjustable Auto Resetting Thermostat turns unit off at 85°C {185°F} Less than 15 seconds
Stand-by Power
Less than 0.5W
Circuit Operation
Infrared Automatic, self adjusting
Sensor Range
Standard [170 ± 20mm], Adjustable, The range is [120 - 220mm]
Timing Protection
60 seconds auto shut off
Drip proof
IP14
Isolation Net Weight
CLASS 1 4.5kg
Shipping Weight
5.2kg
Unit Size
263mm (W) x 170mm(H) x 139mm (D)
COVER TYPE/ COVER FINISH BC2003BM- Stainless steel; #4 satin finished. (AISI 304 t:1.2 mm)
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
General safety information WARNING
WARNING Disconnect power at the service breaker before installing or servicing. Not for household use may cause burns.
This product is intended for installation by a qualified service person. Use 1.2mm² solid conductor for wiring.
DANGER
WARNING
Failure to properly ground unit could result in severe electrical shock and/or death.
All units must be supplied with a 3-wire service. The ground wire must be connected to the dryer's backplate.
NOTE: We do not recommend that this dryer is installed above a basin. If you are installing this dryer above a basin you need to satisfy yourself that reflection won’t occur.
【Type Y attachment】 If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Circuit Diagram L N
Red(110-120V)/Brown (208-240~277V)
G
MO2 HE2
L
MO1 HE1
Transistor Power Switch (ONLY 208~240V)
G/Y
Heater With Thermo-fuse
G/Y
N
VR FOR SENSOR Y2 Filter
(ONLY 208~240V)
VR FOR MOTOR Circuit Board Module
Transistor Power Switch G
Motor With Thermal Switch 2A
Blue
Brown
Black
Thermostat
Black
White(110-120V)/Blue (208-240~277V)
ON
1
SW.FOR HEATER Sensor module
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
Installation 1. Make sure power supply breaker is switched off. Installation must be carried out in accordance with the current edition of the local wiring regulations code having jurisdiction. Installation should be performed only by a qualified electrician. 2. Place template against wall at desired height (see mounting height recommendations) and mark locations of 4 mounting holes and wire service entry at knockout (KO) location. Note: For two or more dryers, dryers should be no closer than 24 inches (610mm) on center.
1
4
Remove and retain 2 cover screws and cover.
Fix the part to the wall with 4 screws of 1/4 x 1-3/4" dimension.
2
5
K.O hole
Back K.O hole Insert the power cord into the suitable K.O. hole.
Put the front cover back and screw it with L key.
3 Connect the wire into terminal as below: Connections: A. Connect the live wire (colored red or black or brown) to the terminal block marked "L". B. Connect the neutral wire (colored white or blue) to the terminal block marked "N". C. Connect the ground wire (colored green or green and yellow) to the terminal block marked " ".
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
Operation No-touch operation. Operation Shake excess water from hands. Place hands under the outlet to start operation. Rub hands lightly and rapidly. Stops automatically after hands are removed.
Cleaning and Maintenance Periodic cleaning of the unit is recommended to ensure optimum performance. Disconnect the electrical supply. Remove the two cover-mounting screws. Remove the cover. Clean all dust lint from the interior of the dryer. Wipe the cover with a damp cloth and mild cleaning solution. Do not Soak. Never use abrasives to clean the cover. Replace the cover. Do not over tighten the screws.
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
Settıng Adjustmenet A. Warm air speed adjustment
VR.FOR AIR SPEED Use phillips screw to adjust air speed. Clockwise: Increases the air speed(+) . Counterclockwise: Decreases the air speed(-)
.
Install the cover once adjustment is completed.
B. Heater Element Switch ON/OFF 1.Switch off the power, loosen the cover screws and remove the cover. 2.Adjust the heater switch on the PCB with a small plastic or wood flat blade probe. 2-1. Heater ON: Slide the switch to "ON". 2-2. Heater OFF:Slide the switch to "1".
SW.FOR HEATER
C. Sensor range adjustment Operation
1.The recommended unit sensor range is 150mm. This can be adjusted from 120mm to 220mm. . 2.Clockwise: Increases the sensing range(+) 3.Counterclockwise: Decreases the sensing range(-) 4.DO NOT OVERTURN!
BC2003BM User Manual
VR.FOR SENSOR
.
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
Surface-mounted high speed hand drier
Timer replacement
1. Pull off the four wires and remove the fixing screws of the timer.
2. Ensure that the two flanges on the timer to be wedged in the two holes are on the base plate. 3. Fix the timer to the blower and connect the four wires to the timer as the photos of procedure 1.
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
Surface-mounted high speed hand drier
Sensor replacement
1. Pull off the wires that connect timer and remove the fixing screws of the timer. 2. Fix the sensor on the sensor bracket as in the photos of procedure 1, and plug the wires on the timer.
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
Motor replacement
1. Remove the wires that connect motor to the timer.
2. Loosen the fixing screws of the blower and remove the blower housing.
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
3. To replace the motor, install the motor rubber (large/small) on the motor, and place the motor under the fan blower.The wire set must be fixed to the ditch in the lower housing of the blower.
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
Heater replacement
1. Remove the wires that connect heater to the timer.
2. Loosen the fixing screws of the blower and remove the blower housing.
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
3. To replace the heater, the wire set must be fixed to the ditch in the lower housing of the blower.
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
Tools
Philips Screwdriver Slotted Screwdriver Wire Cutter Modular Crimping Cuts Tool
Important Information This Product falls within the scope of the Waste Electrical & Electronic Equipment Directive 2002/96 EC. (WEEE)
NOTE:
This Product should not be disposed of with household waste Please recycle where facilities exist. Check with your local authority for recycling advice.
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
Diagnostics and Remedies Symptom If the dryer will not run
Corrective Actions for Initial Installation Failures First ensure that the breaker supplying the dryer is operational. If it is, disconnect the power and remove the dryer cover. Taking suitable precautions to avoid shock hazard, reconnect the power and check for Voltage at the terminal block. Verify that connections are made correctly.
The dryer cycles by itself or runs constantly
Ensure that there is no obstruction on or in front of the IR sensor. Clean any dirt or debris off the sensor lens. If problem persists, replace sensor.
The dryer makes a loud noise and does not run for a complete cycle
Ensure that the supply Voltage is correct. Dryer will make a loud humming noise if the input Voltage is too high. Verify Voltage requirement on unit rating label and correct supply as required. If CBM has been damaged, replace CBM, IR sensor module and VR component and cable.
The dryer runs but air stream is low pressure and/or low velocity
Ensure that the supply Voltage is correct. Dryer will run weakly if the input Voltage is too low. Verify Voltage requirement on unit rating label and correct supply as required.
Symptom
Corrective Actions for In-Service Failures
If the dryer will not run
First ensure that the breaker supplying the dryer is operational. If it is, disconnect the power and remove the dryer cover. Replace the CBM and IR sensor module. Taking suitable precautions to avoid shock hazard, reconnect the power and check for voltage at the terminal block.
The IR sensor only "sees" close range objects
Ensure that there is no obstruction on or in front of the IR sensor. Clean any dirt or debris off the sensor lens. Check VR for sensor range setting, If problem persists, disconnect the power and remove the dryer cover and replace CBM, IR sensor module.
The heater gets hot but no air stream is produced or the air stream is low pressure and velocity
Disconnect the power. Remove the dryer cover and disassemble the blowermotor/fan housing. Replace the fan motor.
The dryer only blows cold air during a full cycle
Disconnect the power. Remove the dryer cover and disassemble the blower-motor/fan housing. Test the thermostat for open circuit. Check the heater element for signs of burning or breakage. Damaged element must be replaced.
Warranty LIMITED THREE-YEAR WARRANTY Please see our website by following this link: http://www.dolphinsolutions.co.uk/ or contact our customer service team on 01424 202224 for more details.
BC2003BM User Manual
www.dolphinsolutions.co.uk
Hand drier
Operating Instructions and Parts Manual
Diagram 3 6 5 8
20
21
7
4
22
9
10 11 12
1
13 17
2
14
19 18
15 16
Repair parts list Key
Description
Key
1
Enclosure (Casing)
12
Description Insulation Mylar
2
Security hex screw (2 reqd.)
13
Terminal block
3
Blower housing - Upper
14
Blower mounting bracket
4
Blower housing - Below
15
Sensor bracket
5
Motor
16
Sensor
6
Motor rubber - Small
17
Cable clamp
7
Motor rubber - Large
18
Cable Protector
8
Heater assembly
19
Grounding Screw
9
Circuit Board Module
20
Left box bracket
10
Base plate
21
Right box bracket
11
Nylon hole bushing
22
Box
BC2003BM User Manual
www.dolphinsolutions.co.uk
Dolphin Solutions Ltd Southpoint, Compass Park, Junction Road Bodiam, TN32 5BS, United Kingdom T +44 (0)1424 202 224
[email protected] dolphinsolutions.co.uk © Dolphin Solutions Ltd
BC2003BM User Manual
www.dolphinsolutions.co.uk
240
110
90
DP2109
DOLPHIN TOILET ROLL HOLDER › Superior quality and timeless design for prestigious washrooms › Easy-care 18/10 chrome nickel stainless steel
HEIGHT
110
MM
WIDTH
240
MM
90
MM
PROJECTION
› Satin finish, welded corners - no sharp edges › Enhanced vandal resistant construction › Easy to clean and maintain › Lockable › No more toilet roll theft › Capacity two toilet rolls › Also available in polished stainless steel or plastic powder coated to a colour of your choice
PRODUCT CODES › Single toilet roll holder see
DP2108
TECHNIC AL HELPLINE 01424 202224 DOLPHINSOLUTIONS.CO.UK
DP 2109 BELL-CHEM PRODUCTS COMPANY DOLPHIN PRESTIGE TOILET ROLL HOLDER
240
110
90
DP2109PVD
DOLPHIN TOILET ROLL HOLDER › Superior quality and timeless design for prestigious washrooms › Easy-care 18/10 chrome nickel stainless steel
HEIGHT
110
MM
WIDTH
240
MM
90
MM
PROJECTION
› Welded corners - no sharp edges › Enhanced vandal resistant construction › Easy to clean and maintain › Lockable › No more toilet roll theft › Capacity two toilet rolls › Also available in polished stainless steel or plastic powder coated to a colour of your choice
PRODUCT CODES › Single toilet roll holder
DP2108
› Satin stainless steel verion of this procuct
DP2109
TECHNIC AL HELPLINE 01424 202224 DOLPHINSOLUTIONS.CO.UK
380
Ø 89
DP7504
DOLPHIN TOILET BRUSH SET › Superior quality and timeless design for prestigious washrooms
HEIGHT DIAMETER
› Easy-care 18/10 chrome nickel stainless steel
PROJECTION
380
MM
89
MM
100
MM
› Satin finish › Anti-theft, robust four-point wall fixing › Replaceable brush head and chrome nickel steel handle › Container diameter 89mm › Available in satin or polished stainless steel PRODUCT CODES › Satin version see › Polished version see › Replacement head see
DP7104 DP7104PSS DP7104BRUSH
TECHNIC AL HELPLINE 01424 202224 DOLPHINSOLUTIONS.CO.UK
DP 7504
Overview Spare Parts for DP 7504
Replacement Brush Head For Toilet Brush Sets 700223
Container Satin Finish 924209
Container Holder Satin Finish 924213
Handle Satin Finish 924269
Handle with Brush Satin Finish 924278
Container Highly Polished 931209
Container Holder Highly Polished 931213
Handle Highly Polished 931269
Handle with Brush Highly Polished 731278
Southpoint, Compass Park, Bodiam, Robertsbridge TN32 5BS Tel: 01424 202224 Fax: 01424 205200 www: dolphindispensers.co.uk
[email protected]
DOLPHIN
130 730 to paper towel
1198
298
10
DP4313
DOLPHIN PAPER TOWEL DISPENSER AND WASTE BIN COMBINATION UNIT › Superior quality and timeless design for prestigious washrooms › Easy-care 18/10 chrome nickel stainless steel combination unit › Satin finish, welded corners - no sharp edges › Double skin door › Towel capacity: 250 paper towels
HEIGHT
748
MM
WIDTH
298
MM
PROJECTION
FLUSH
RECESS DIMENSIONS HEIGHT
750
MM
WIDTH
300
MM
PROJECTION
130
MM DEEP
› Bin capacity: 7 litres › Removable chrome-plated wire basket › Can be installed flush with tiles › SKA Compliant Product › Also available in polished stainless steel or plastic powder coated to a colour of your choice
TECHNIC AL HELPLINE 01424 202224 DOLPHINSOLUTIONS.CO.UK
DP 4313 BELL-CHEM PRODUCTS COMPANY DOLPHIN PRESTIGE PAPER TOWEL DISPENSER AND WASTE BIN COMBINATION UNIT
Overview Spare Parts for DP 4313
Mesh Basket 264 x 222 x 123mm 7 litres 924725
Key Lock Lock 1 pair (from 1999) 924455
Key Lock A Line Straight Lug (from 1999) 924450
Southpoint, Compass Park, Bodiam, Robertsbridge TN32 5BS Tel: 01424 202224 Fax: 01424 205200 www: dolphindispensers.co.uk
[email protected]
DOLPHIN
S O U T H PO I N T, CO M PA S S PARK, B O DI A M , RO B E RTS B R I DG E , T N 3 2 5 B ST, U N I T E D K I N G D OM + 44 (0)1424 202 224
TEL
+ 44 (0)1424 205 200
FA X
h e l l o @ d o l p i n so l u t i o n s.c o .u k d o l p h i n so l u t i o n s.c o .u k
