Transcript
Optoway
SPB-7620WG
1
***********************************************************************************************************************************************************************
SPB-7620WG / SPB-7620BWG / SPB-7620AWG (SC BIDI SFP) (RoHS Compliant) SPB-7620LWG / SPB-7620BLWG / SPB-7620ALWG (LC BIDI SFP) 1310 nm TX / 1550 nm RX , 3.3V / 1250 Mbps Digital Diagnostic Single-Fiber SFP Transceiver **********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l l l l l l l l l l l l l l l
The SPB-7620WG series is small form factor pluggable module for Gigabit Ethernet 1000BASE-BX and Fibre Channel single fiber communications by using 1310 nm transmitter and 1550 nm receiver. It is with the SFP 20-pin connector to allow hot plug capability. Digital diagnostic functions are available via an I2C. The transmitter section uses a multiple quantum well 1310 nm laser and is a class 1 laser compliant according to International Safety Standard IEC 60825. The receiver section uses an integrated 1550 nm detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC.
1-Fiber Bi-Directional SFP Optical Transceiver Compliant with IEEE 802.3ah-2004 1000BASE-BX Simplex SC Connector: SPB-7620WG Simplex LC Connector: SPB-7620LWG SFF-8472 Digital Diagnostic Function 1310 nm LD Transmitter 1550 nm Receiver Distance Up to 20 km AC/AC Coupling according to MSA Single +3.3 V Power Supply RoHS Compliant 0 to 70oC Operating: SPB-7620WG -10 to 85oC Operating: SPB-7620BWG -40 to 85oC Operating: SPB-7620AWG Class 1 Laser International Safety Standard IEC 60825 Compliant
APPLICATIONS l WDM Gigabit Ethernet Links l SONET/SDH Equipment Interconnect l Fibre Channel Links
LASER SAFETY This single mode transceiver is a Class 1 laser product. It complies with IEC 60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug.
ORDER INFORMATION P/No. SPB-7620WG SPB-7620BWG SPB-7620AWG SPB-7620LWG SPB-7620BLWG SPB-7620ALWG
Bit Rate (Gb/s) 1.25 1.25 1.25 1.25 1.25 1.25
Distance (km) 20 20 20 20 20 20
TX (nm) 1310 1310 1310 1310 1310 1310
RX (nm) 1550 1550 1550 1550 1550 1550
Package SC SFP with DMI SC SFP with DMI SC SFP with DMI LC SFP with DMI LC SFP with DMI LC SFP with DMI
Temp TX Power (oC) (dBm) 0 to 70 -3 to -8 -10 to 85 -3 to -8 -40 to 85 -3 to -8 0 to 70 -3 to -8 -10 to 85 -3 to -8 -40 to 85 -3 to -8
RX Sens. (dBm) -22 -22 -22 -22 -22 -22
RoHS Compliant Yes Yes Yes Yes Yes Yes
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
1/1/2008
V3.0
Optoway
SPB-7620WG
2
***********************************************************************************************************************************************************************
Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature
Symbol Tstg Topr
Relative Humidity Power Supply Voltage Input Voltage
RH Vcc ---
Min -40 0 -10 -40 0 0 GND
Max 85 70 85 85 85 3.6 Vcc
Units o C o C
Output Current
Iout
0
30
mA
Min 3.1
Typ 3.3 200
Max 3.5 300 70 85 85 1300
% V V
Notes SPB-7620WG SPB-7620BWG SPB-7620AWG Non condensing
Recommended Operating Conditions Parameter Power Supply Voltage Power Supply Current Operating Case Temperature
Symbol Vcc ICC (TX+RX) Topr
0 -10 -40
Data Rate
1250
Units / Notes V mA o C / SPB-7620WG o C / SPB-7620BWG o C / SPB-7620AWG Mb/s
Transmitter Specifications (0 oC < Topr < 70 oC, 3.1V < Vcc < 3. 5V) Parameter
Symbol
Min
Optical Optical Transmit Power Po -8 Output Center Wavelength 1270 λ Output Spectrum Width σλ Extinction Ratio ER 9 Output Eye Compliant with IEEE 802.3z Optical Rise Time tr Optical Fall Time tf Relative Intensity Noise RIN Total Jitter TJ Electrical Data Input Current – Low IIL -350 Data Input Current – High IIH Differential Input Voltage VIH - VIL 0.5 TX Disable Input Voltage – Low TDIS, L 0 TX Disable Input Voltage – High TDIS, H 2.0 TX Disable Assert Time TASSERT TX Disable Deassert Time T DEASSERT TX Fault Output Voltage -- Low TFaultL 0 TX Fault Output Voltage -- High TFaultH 2.0
Typ
Max
Units
Notes
-3 1355 2
dBm nm nm dB
1
1310
0.26 0.26 -120 0.227
ns ns dB/Hz ns
350 2.4 0.5 Vcc 10 1 0.5 Vcc+0.3
µA µA V V V µs ms V V
RMS (σ)
20% to 80% Values 20% to 80% Values 2
Peak-to-Peak 3 3
4 4
Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. Measured with a 27-1 PRBS. 3. There is an internal 4.7K to 10K ohm pull-up resistor to VccTX. 4. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage).
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
1/1/2008
V3.0
Optoway
SPB-7620WG
3
***********************************************************************************************************************************************************************
Receiver Specifications (0oC < Topr < 70oC, 3.1 V < Vcc < 3. 5V) Parameter Optical Sensitivity Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation Optical Return Loss Electrical Differential Output Voltage Output LOS Voltage -- Low Output LOS Voltage – High Signal Detect Assert Time Signal Detect Deassert Time
Symbol
Min
Typ
Max
Units
Notes
--Pin Pa Pd
---3 ---35 1.0 1480 14
-----------
-22 ---22 ---
dBm dBm dBm dBm dB nm dB
5
ORL VOH – VOL VOL V OH ASMAX ANSMAX
1580
0.6 0 2.0
2.0 0.5 Vcc+0.3 100 300
Transition: low to high Transition: high to low
V V V µs µs
6
7 7 OFF to ON ON to OFF
Notes: 5. Minimum sensitivity and saturation levels at BER 1E-12 for a 27-1 PRBS. 6. At least 30 dB optical isolation for the wavelength 1260 to 1360 nm. 7. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage).
RECOMMENDED CIRCUIT SCHEMATIC VeeT Tx_DISABLE Tx_FAULT
(1,17,20) 3
Tx_DISABLE
2
Tx_FAULT 4.7K to 10KΩ
TD +
LD Driver
18
TD + Z=50Ω
100Ω TD -
19
TD Z=50Ω
VccT
1μH
16
Vcc 3.3V 10μF
10nF
10μF
10nF
SerDes IC
1μH VccR
15
RD -
Protocol IC
10μF
10nF
12
RD Z=50Ω 100Ω
POST Amp
RD +
13
RD + Z=50Ω 4.7K to 10KΩ
LOS VeeR MOD_DEF(0)
EEPROM
MOD_DEF(1) MOD_DEF(2)
SFP module
depending on SERDES
8
LOSS OF SINGAL
(9,10,11,14) 6
MODULE DETECT
5
SCL
4
SDA 4.7K to 10KΩ
4.7K to 10KΩ
Vcc 3.3V 4.7K to 10KΩ
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
1/1/2008
V3.0
Optoway
SPB-7620WG
4
***********************************************************************************************************************************************************************
CONNECTION DIAGRAM
PIN
Signal Name
1 2 3
TX GND TX Fault TX Disable
4
MOD-DFE2
5
MOD-DEF1
6
MOD-DEF0
7 8 9 10
N/C LOS RX GND RX GND
Description
PIN
Transmitter Ground Transmitter Fault Indication Transmitter Disable (Module disables on high or open) Modulation Definition 2 – Two wires serial ID Interface Modulation Definition 1 – Two wires serial ID Interface Modulation Definition 0 – Ground in Module Not Connected Loss of Signal Receiver Ground Receiver Ground
11 12 13
RX GND Receiver Ground RX DATA OUT- Inverse Receiver Data Out RX DATA OUT+ Receiver Data Out
Signal Name
Description
14
RX GND
Receiver Ground
15
Vcc RX
Receiver Power – 3.3V±5%
16
Vcc TX
Transmitter Power – 3.3V±5%
17 18 19 20
TX GND TX DATA IN+ TX DATA INTX GND
Transmitter Ground Transmitter Data In Inverse Transmitter Data In Transmitter Ground
Module Definition Module Definition
MOD-DEF2 PIN 4
MOD-DEF1 PIN 5
MOD-DEF0 PIN 6
Interpretation by Host
4
SDA
SCL
LV-TTL Low
Serial module definition protocol
Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E 2PROM protocol of the ATMEL AT24C01A/02/04 family of components.
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
1/1/2008
V3.0
Optoway
SPB-7620WG
5
***********************************************************************************************************************************************************************
PACKAGE DIAGRAM Units in mm A) SC SFP
A) LC SFP
Note: Specifications subject to change without notice.
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
1/1/2008
V3.0
Optoway
SPB-7620WG
6
***********************************************************************************************************************************************************************
Revision History Version 1.0 2.0 3.0
Subject
Release Date
Initial datasheet Combine datasheet of SC BIDI SFP and LC BIDI SFP Revise SC BIDI SFP package diagram for high port density use
2005/12/1 2006/3/1 2008/1/1
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
1/1/2008
V3.0
