Transcript
4. NOMENCLATURE AND FUNCTIONS
OPERATING INSTRUCTIONS
SPEAKER SELECTOR
[Left side]
[Front]
[Right side]
SS-9001 9000 SERIES SPEAKER SELECTOR
Thank you for purchasing TOA's Speaker Selector. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
1
IN 1 70V/100V MAX. 240W
5
ZONE 1
IN 2
IN 2 70V/100V MAX. 240W
ZONE 2
CTRL IN
2
ZONE G ZONE G ZONE G ZONE G
IN 2 1 2 3
ZONE 3
197
157
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. • Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety. • After reading, keep this manual handy for future reference.
177
1. SAFETY PRECAUTIONS
4 IN 2
WARNING
Indicates a potentially hazardous situation which, if mishandled, could result in death or serious personal injury.
DC IN
24V 120mA ZONE 4
3
IN 2
requires installation by an instructed
4 10
• External wiring connected to the terminals marked with person.
2. GENERAL DESCRIPTION The SS-9001 is a speaker selector used with 9000 series amplifier. It selectively distributes each of 2 inputs to the same 4 output zones.
1
18 30
70 112
18
Unit: mm
3. SPECIFICATIONS Power Source Current Consumption Control Signal Control Power Speaker Terminal Control Terminal Operating Temperature Finish Dimensions Weight Accessories
Supplied from the optional AD-246 AC adapter or an external 24 V DC/200 mA power supply. 120 mA No-voltage make contact input (polarized), open voltage: 24 V DC, short-circuit current: 3 mA Under 240 W (70 V/100 V line) Removable terminal block (2 pins) Removable terminal block (10 pins) –10 to +40°C Case: Surface-treated steel plate 112 (w) x 197 (h) x 30 (d) mm 530 g Removable terminal plug (2 pins) x 6, Removable terminal plug (10 pins) x 1, Cord clamp x 1, Tapping screw (4 x 20) x 4
Note: The design and specifications are subject to change without notice for improvement.
1. Speaker input terminals [IN 1, IN 2] 2-pin removable terminal blocks. Connect the speaker output (high impedance line, up to 240 W) from the power amplifier to each terminal. Short the IN 2 terminal's pins when only the IN 1 terminal is used. 2. Control input terminal [CTRL IN] 8 pins in the 10-pin removable terminal block. Receives the control signals (polarized nonvoltage contacts) from the ZP-001T when the 9000 series amplifier is in the Matrix "SubMode" (single output or BGM/PAGE), and activates the inner relays. This terminal can also receive control signals from the control output terminals of the 9000 series amplifier or C-001T Control I/O Expansion Module. (For details, refer to the 9000 series amplifier's instruction manual.)
3. DC power input terminals [DC IN] Requires the power input of 24 V DC. DC input terminal or 2 pins in the 10-pin removable terminal block. Connect the power source that can supply 200 mA or more to this terminal. The optional AD-246 AC Adapter can be used for the power supply. 4. Cord clamp Fixes the AC adapter's power cord. 5. Speaker output terminals [ZONE 1/2/3/4] 2-pin removable terminal blocks. Connect speakers to each terminal, which is capable of delivering 240 W output on a line.
5. CONNECTIONS
6.2.When Using the Optional AC Adapter
The control input terminals of SS-9001 are polarized non-voltage contact inputs. With the output terminal setting in the 9000 series amplifier, the SS-9001's internal relays can be activated. Make necessary connections depending on applications.
Connect the optional AD-246 AC Adapter to the SS-9001's DC power input terminal shown at right. Pinch the adapter cord with the cord clamp to securely fix the cord.
5.1. Connecting the 9000 Series Amplifier
REMT VOL1 IN E IN E 1 2 3 4 E 1 2 3 4 E
REMT VOL2 IN
OUT
DC IN 24V 120mA
REMT VOL2
IN
Control-I/O connection terminal
CTRL IN ZONE 1 G ZONE 2 G ZONE 3 G ZONE 4 G
Be sure to use the supplied removable terminal plugs for connections to the removable terminal blocks.
[Cable end treatment]
Solid or stranded cable
7 mm
SS-9001
C-001T module OUT
C-001T
1 2 3 4 5 6 7 8 E
7. REMOVABLE TERMINAL PLUG CONNECTION
Caution Avoid soldering stranded cable, as contact resistance may increase when the cable is tightened and the solder is crushed, possibly resulting in an excessive rise in joint temperatures.
5.2. Connecting the C-001T Module
IN
Cord clamp
SS-9001
IN E IN E 1 2 3 4 E 1 2 3 4 E
OUT
OUT
AC adapter (optional)
CTRL I/O
9000 Series amplifier CTRL I/O REMT VOL1
[Left side]
CTRL IN ZONE 1 G ZONE 2 G ZONE 3 G ZONE 4 G
1 2 3 4 5 6 7 8 E
Control output terminal
Connect a 24V DC power source to the SS-9001's DC power input terminal shown at right. Notes • The DC power supply unit should be capable of supplying 200 mA or more. • The DC power fed to this terminal should be from 21.6 to 26.4 V. If the input voltage exceeds this range, the SS-9001 may malfunction or fail.
Slotted screwdriver
Step 1. Loosen the terminal screw, then insert the cable. Step 2. Loosen the terminal screw, then insert the cable. (Pull on the cable to ensure it is securely connected.)
2
[Left side]
From 24 V DC power source
Loosens
Terminal screw
Bit shape 3 mm
DC IN 24V 120mA
1
Tightens
Tip Recommended slotted screwdriver type: Screwdriver with 3 mm blade width
6. POWER SOURCE CONNECTIONS 6.1. When Using a 24 V DC Power Source
[Connector connection]
1 Removable terminal plug (accessory) Cable
Traceability Information for Europe (EMC directive 2004/108/EC) Manufacturer: TOA Corporation 7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo, Japan
Authorized representative: TOA Electronics Europe GmbH Suederstrasse 282, 20537 Hamburg, Germany
URL: http://www.toa.jp/ 133-05-400-4A
