Transcript
FDC10 FDC10W
SERIES
DC-DC CONVERTER
2:1 & 4:1 WIDE INPUT RANGE UP TO 10 WATTS
FEATURES
APPLICATIONS
• NO MINIMUM LOAD REQUIRED • 1600VDC INPUT TO OUTPUT ISOLATION • STANDARD 2.00 X 1.00 X 0.40 INCH • SIX-SIDED CONTINUOUS SHIELD • UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH
1600VDC ISOLATION
REMOTE CONTROL
OCP
SCP
• WIRELESS NETWORK • TELECOM/DATACOM • INDUSTRY CONTROL SYSTEM • DISTRIBUTED POWER ARCHITECTURES • SEMICONDUCTOR EQUIPMENT
OVP
TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25ºC otherwise noted Model Number FDC10-12S33 FDC10-12S05 FDC10-12S12 FDC10-12S15 FDC10-12D05 FDC10-12D12 FDC10-12D15 FDC10-24S33 FDC10-24S05 FDC10-24S12 FDC10-24S15 FDC10-24D05 FDC10-24D12 FDC10-24D15 FDC10-48S33 FDC10-48S05 FDC10-48S12 FDC10-48S15 FDC10-48D05 FDC10-48D12 FDC10-48D15
Input Range
Output Voltage
Output Current @ Full Load
Input Current @ No Load
Efficiency
Maximum Capacitor Load (1)
VDC 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75
VDC 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15
mA 2000 2000 830 670 ±1000 ±416 ±333 2000 2000 830 670 ±1000 ±416 ±333 2000 2000 830 670 ±1000 ±416 ±333
mA 17 21 38 36 39 47 45 15 22 18 36 28 24 31 11 14 14 10 16 19 16
% 80 81 84 84 84 83 84 80 82 84 84 83 85 84 80 84 86 87 84 86 85
µF 6800 4700 690 470 ±680 ±330 ±110 6800 4700 690 470 ±680 ±330 ±110 6800 4700 690 470 ±680 ±330 ±110
Advice Electronics Ltd Advice Building,16 Atir Yeda St., Kfar Saba, 4464321, Israel Tel:+972-3-9000910
[email protected]
www.advice.co.il
Model Number
Input Range
Output Voltage
VDC 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75
VDC 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15
FDC10-24S33W FDC10-24S05W FDC10-24S12W FDC10-24S15W FDC10-24D05W FDC10-24D12W FDC10-24D15W FDC10-48S33W FDC10-48S05W FDC10-48S12W FDC10-48S15W FDC10-48D05W FDC10-48D12W FDC10-48D15W
Output Current @ Full Load mA 2500 2000 830 670 416 ±1000 ±416 ±333 2500 2000 830 670 416 ±1000
Input Current @ No Load mA 13 11 16 26 15 15 22 10 9 9 11 12 20 20
Maximum Capacitor Load (1) µF 6800 4700 690 470 ±680 ±330 ±110 6800 4700 690 470 ±680 ±330 ±110
Efficiency % 78 80 84 81 82 80 80 76 81 84 84 82 78 81
PART NUMBER STRUCTURE
FDC10 Series name
48
S
05
Input Voltage (VDC)
Output Quantity
Output Voltage (VDC)
12: 9~18 24: 18~36 48: 36~75
S: Single
33: 05: 12: 15: 05: 12: 15:
D: Dual
FDC10 Series name
3.3 5 12 15 ±5 ±12 ±15
48
S
05
Input Voltage (VDC)
Output Quantity
Output Voltage (VDC)
24: 9~36 48: 18~75
S: Single
D: Dual
33: 05: 12: 15:
3.3 5 12 15
M1
P
HS
Version Code
Remote On/Off Option
Assembly Option
: Standard Version M1: M1 Version M2: M2 Version
W Input Range 4:1
P: Positive logic N: Negative logic
: None HS: Heat-sink HC: Heat-sink with Clamp
P
HS
Remote On/Off Option
Assembly Option
P: Positive logic N: Negative logic
: None HS: Heat-sink HC: Heat-sink with Clamp
05: ±5 12: ±12 15: ±15
INPUT SPECIFICATIONS Parameter Operating input voltage range
-
Conditions FDC10 series
FDC10W series
12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom)
Input reflected ripple current Start up time Input surge voltage
Constant resistive load 100 ms, max.
Power up 12Vin(nom) 24Vin(nom) 48Vin(nom)
Input filter Remote ON/OFF (Option)
Referred to –Vin pin
Positive logic
DC-DC ON DC-DC OFF Negative logic DC-DC ON DC-DC OFF Input current of Ctrl pin Remote off input current
Min.
Typ.
Max.
9 18 36 9 18
12 24 48 24 48 30 20
18 36 75 36 75
-0.5
VDC VDC mAp-p ms
36 50 VDC 100 Pi type Open or 3.5 ~ 12VDC Short or 0 ~ 1.2VDC Short or 0 ~ 1.2VDC Open or 3.5 ~ 12VDC +1.0 mA 20 mA
Advice Electronics Ltd Advice Building,16 Atir Yeda St., Kfar Saba, 4464321, Israel Tel:+972-3-9000910
Unit
[email protected]
www.advice.co.il
OUTPUT SPECIFICATIONS Parameter
Conditions
Voltage accuracy Line regulation Load regulation
Low Line to High Line at Full Load No Load to Full Load
Cross regulation Ripple and noise
Asymmetrical load 25%/100% FL Measured by 20MHz bandwidth
Temperature coefficient Transient response recovery time Over voltage protection
25% load step change Zener diode clamp
Isolation voltage
1 minute
Isolation resistance Isolation capacitance Switching frequency Safety approvals
500VDC
Max.
Unit
+1.0 +0.2 +0.5 +1.0 +5.0
% %
50 75 +0.02
3.3Vout 5Vout 12Vout 15Vout
%
%/ºC µs VDC
150 % Continuous, automatics recovery
Conditions
Min.
Input to Output Input (Output) to Case
1600 1600 1
MIL-HDBK-217F, Full load
Conditions
Standard M1 (2) M2, W series
Typ.
GΩ pF 300 kHz UL60950-1 EN60950-1 IEC60950-1 Nickel-coated copper Non-conductive black plastic Epoxy (UL94 V-0) 27g (0.95oz) 3.342 x 106 hrs 300 330
Typ.
-25 -40 -40
Without heat-sink With heat-sink
Max. +85 +85 +85 +105 +125
-55 Vertical direction by natural convection (20LFM)
Unit VDC
Min. With derating Without derating With derating
Max.
12 10
Unit ºC
ºC ºC/W
Thermal shock Vibration Relative humidity
MIL-STD-810F MIL-STD-810F 5% to 95% RH
EMC SPECIFICATIONS Parameter EMI (3) ESD Radiated immunity Fast transient (4) Surge (4) Conducted immunity Power frequency magnetic field
%
mVp-p
250 3.9 6.2 15 18
270
ENVIRONMENTAL SPECIFICATIONS Parameter
Maximum case temperature Storage temperature range Thermal impedance
Single Dual Dual Single Dual
% of Iout rated
GENERAL SPECIFICATIONS Parameter
Operating ambient temperature
Typ.
-1.0 -0.2 -0.5 -1.0 -5.0
-0.02
Over load protection Short circuit protection
Case material Base material Potting material Weight MTBF
Min.
Conditions EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 EN61000-4-8
Level
Air ± 8kV and Contact ± 6kV 10 V/m ± 2kV ± 2kV 10 Vr.m.s 100A/m continuous; 1000A/m 1 second
Class B Perf. Criteria B Perf. Criteria A Perf. Criteria B Perf. Criteria B Perf. Criteria A Perf. Criteria A
Note: 1. 2. 3. 4.
Test by minimum input and constant resistive load. M1 version is more efficient, therefore, it can be operated in a more extensive temperature range than standard and M2 version. The standard module meets EN55022 Class A and Class B with external components. For further information, please contact with P-DUKE. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V.
CAUTION: This power module is not internally fused. An input line fuse must always be used.
Advice Electronics Ltd Advice Building,16 Atir Yeda St., Kfar Saba, 4464321, Israel Tel:+972-3-9000910
[email protected]
www.advice.co.il
CHARACTERISTIC CURVE
FDC10-48S05 Derating Curve
FDC10-48S05 Derating Curve With Heat-sink
FDC10-48S05 Efficiency vs. Input Voltage
FDC10-48S05 Efficiency vs. Output Load
MECHANICAL DRAWING PIN CONNECTION PIN 1 2 3 4 5 6
SINGLE +Vin -Vin +Vout No pin -Vout Ctrl(Option)
DUAL +Vin -Vin +Vout Common -Vout Ctrl(Option)
1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1)
Advice Electronics Ltd Advice Building,16 Atir Yeda St., Kfar Saba, 4464321, Israel Tel:+972-3-9000910
[email protected]
www.advice.co.il
