Transcript
WM, WD, WS, WE, 15WM & NEMA Series Wall Mounts
Thank you for your business!
Installation Instructions
WDS
ISO 9001 : 2008
WM
ETSI Associate Member
WeRackYourWorld.com MS-5.02-10 Rev.2
1-866-TRY-GLCC (879-4522)
Wall Mount AcCESSORIES PART NO.
DESCRIPTION
WM WS WD WE NEMA
DK2*
Dust Resistant Kit, 4 cover plates, 4 fan filters and hardware
3 q
q
q
q q
FFK1
Four Fan Filters
3 q
3 q
3 q
q q
3 HDW-104-50 Package of 50 Pan Head q Phillips #12-24 x 1/2" screws Type 23, Black
3 q
3 q
q q
WS-22
3 q
3 q
3 q q
66/110 Block Mounting Panel
3 q
* Will not fit GL2418WM
Thank you for your business!
When installing a Great Lakes wall-mounted rack enclosure to materials such as wood, cinder block, concrete, etc., please consider the load capacity within the wall mount structure, and be certain to check with local authorities to determine the appropriate hardware requirements for these conditions. Because wall compositions may vary at different installation sites, Great Lakes cannot warrant the fitness or suitability of any installation instructions or installation hardware it may provide for wall-mount rack enclosures. Great Lakes hereby DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THE SUFFICIENCY, FITNESS OR SUITABILITY OF ANY INSTALLATION INSTRUCTIONS OR INSTALLATION HARDWARE GREAT LAKES MAY PROVIDE FOR WALL-MOUNTED ENCLOSURES. Great Lakes recommends that an experienced maintenance and/or technical person be consulted regarding the proper wall-mounting hardware and procedures to be used for the anticipated load capacity of the wall-mounted rack enclosure. Product specifications are subject to change without prior notice.
Great Lakes Case & Cabinet Co., Inc. P.O. Box 551 • Edinboro, PA 16412 1-866-TRY-GLCC • (1-866-879-4522) Phone: 814.734.7303 Fax: 814.734.3907
WeRackYourWorld.com 11
Wall Mount AcCESSORIES PART NO. DESCRIPTION WM 3 7206-FM* Stationary Front Mount q Shelf 18"D, Wt Cap. 60 lbs. 3 7206-EIA* Stationary Shelf q 18"D, Wt Cap. 80 lbs.
WS WD WE NEMA 3 3 q 3 q q q 3 q
3 q
3 q q
7206-14
3 q
q
3 q
3 q q
3 q
3 q
3 q
3 q q
7206-FR-AHD Stationary Shelf front & q rear mount, adjustable 22.25"D, Wt Cap. 200 lbs.
q
3 q
q q
7206-SL*
3 q
3 q
3 q q
Stationary Shelf 14"D, Wt Cap. 60 lbs.
7206-FR-A18* Stationary Shelf front & rear mount, adjustable 18"D, Wt Cap. 150 lbs.
Sliding Shelf 16.343"W x 17.50"D Wt Cap. 40 lbs.
7206-FRSL-AHD Sliding Shelf front & rear mount sliding, (adj.) 22"D, Wt Cap. 110 lbs.
3 q
3 q
3 q
3 q
3 q q
3 q
3 q
3 3 q q
3 q
3 q
3 3 q q
7219-20AR
3 6 position Power Strip q 15 ft. cord for 19" mounting 3 Rack mount 14 position q (6 front/8 back) Power Strip with surge suppressor 3 6 position Power Strip with q curcuit breaker (20 amp)
7217WS
3 Fan Assembly with fan q guards and (2) 75 CFM fans
3 q
3 q
3 q q
7208WS/WD
Casters, 3 locking and 3 non-locking, 3.625"H
q
3 q
3 q
q q
CBB-19
Copper Bus Bar 19" rack mounted (isolated)
3 q
3 q
3 q
3 3 q q
GR102
Grounding Kit
3 q
3 q
3 q
q q
DK1
Dust Resistant Kit, q 4 cover plates, 4 fan filters and hardware
q
3 q
q q
7219 7219-SR14
Important Notes Regarding wall mount installation When installing a Great Lakes wall-mounted rack enclosure to materials such as wood, cinder block, concrete, etc., please consider the load capacity within the wall mount structure, and be certain to check with local authorities to determine the appropriate hardware requirements for these conditions. Because wall compositions may vary at different installation sites, Great Lakes cannot warrant the fitness or suitability of any installation instructions or installation hardware it may provide for wall-mount rack enclosures. Great Lakes recommends that an experienced maintenance and/or technical person be consulted regarding the proper wallmounting hardware and procedures to be used for the anticipated load capacity of the wallmounted rack enclosure. Maximum weight capacity determined at minimal deflection. (Deflection chart available upon request.) Make sure enclosure is secured and squared on mounting surface. Improper installation will cause excessive deflection.
WS Series Wall MOunt/ SWing Out Enclosure 1. Mounting holes are designed for 1/4"hardware, 16" on center. 2. Use the template on the shipping box to locate your mounting holes. (WM & WS only) 3. WS and WD handles can be found in the hardware bag. 1", 2", 3" and 4" nominal concentric conduit knockouts 24"
Part No. H W D GL24WS 24.00" 24.00" 24.00" GL36WS 36.00" 24.00" 24.00" GL48WS 48.00" 24.00" 24.00"
Fan assembly provisions Optional caster mounting holes
3 q
3 q
3 q 3 q
24" Two pair 19" EIA rails provided with each enclosure
Mounting holes for 1/4" hardware, 16.00" centers
H
Side View
Side View
Front View
Rear View
10 3
REV
.500 .625 .625
WM Series Wall MOunt Enclosure
DESCRIPTION
DATE 9/23/2010
APPROVED WSS
D
1.750 (1 RMU) PATTERN REPEATS
REAR TOP CABLE ACCESS FOR 1", 2", 3" CONDUIT SIZES
1. Mounting holes are designed for 1/4" hardware, 12-24 16.00" on- 2B center. UNC EQUIPMENT
MTG HOLES IN 12 GA RAILS.
C
REAR TOP CABLE ACCESS FOR 1", 2", 3" CONDUIT SIZES
Rear section
TOP VIEW
Option: 2, Fan unit ventilation 12-24 UNC - 2B EQUIPMENT top or bottom mounting MTG HOLES IN 12 GA RAILS. 19" EIA 310-D COMPLIANT Center swing section
DETAIL B
B
19" EIA Rack spaced 2 pair mounting rails tapped #12-24
TOP VIEW
1", 2" and 3" nominal concentric 24.000 conduit knockouts and horseshoe A knockouts; top & bottom rear section SIDE CABLE ACCESS Continuous Hinges on front door & rear4.327 section
17.86 H (H + 2.50) TO
(# RMU) H
6
5
4
D
Part No. H W D GL2418WM 24.00" 21.25" 18.00" GL24WM 24.00" 21.25" 24.50" GL36WM 36.00" FRONT 21.25" 24.50" VIEW w/ DOOR REMOVED24.50" GL48WM 48.00" 21.25"
FOR MOU
REAR - ISO
FRONT - ISO
GLAND PLATES CAN TO ADD OPTIONAL FAN
1/4" LAG SCREWS RECOMMENDED
GLAND PLATES CAN BE REMOVED TO ADD OPTIONAL FANS OR FILTERS 8
7
6
5
REAR SECTION OF 14 GA CRSCENTER SEC HINGED CONSTRUCTION OF 14 GA CONSTRUC 4
3
HINGED CENTER SECTION OF 14 GA CONSTRUCTION
.280 TYP SECTION A-A
RIGHT 16 SIDE Solid Hinged GA VIEW front (RIGHT SIDE VIEW) door w/(2) Draw Latches plus key locking latch w/dust cover SECTION A-A SOLID HINGED 16 GA FRONT DOOR w/ (2) DRAW (RIGHT SIDE VIEW) C
FRONT VIEW
B
DETAIL B
LATCHES PLUS A KEY LOCKING LATCH w/ DUST COVER
DETAIL A
DIMENSIONAL LIMITS APPLY AFTER APPLICATION OF FINISH
1/4" LAG
1
Front View SPECIFICATIONS: NEMA-12 WALL MOUNT Use latch supplied in hardware bag, FRONTRATING VIEW : INDEPENDENTLY TESTED & CERTIFIED, when horseshoe knockout is used NEMA-250-1997 TYPE 12. 1", 2" and 3" rear section nominal INTERPRET DRAWING PER ASME Y14.5M-1994
FRONT
FOR MOUNTING INTO WALL STUDS
D
RIGHT SIDE VIEW
B
9.000
Neoprene Gasket
A
2
16.000 TO
.280 TYP
A
3
A
C
16.000 TO
4.327
9.000
(H + 2.50) TO
Independent locking front 18.312 TO A door & rear section
24.000 B
FOR 1", 2", 3" CONDUIT SIZES
24.000
24.000
Front door
SIDE CABLE ACCESS FOR 1", 2", 3" CONDUIT SIZES
TOP VIEW
(H + 6.00)
PATTERN REPEATS
(H + 6.00)
.500 .625 .625
2. Use the template on the shipping box to locate your mounting holes. 19" EIA 310-D COMPLIANT (WM & WS only) 1.750 (1 RMU) DETAIL B
NOTICE:
PART NUMBER:
cable latch detail Use of this document is subject to QTY PER UNIT: 1 MATERIAL TYPE: a confidentiality and nondisclosure agreement with Great Lakes Case MATERIAL GAUGE: & Cabinet Co., Inc. (GLCC) and may FINISH: not be reproduced, disclosed or utilized in whole or in part without DRAWN DATE 10/5/2007 prior written authorization from GLCC. ANDY
TITLE
SOLID HINGED 16 GA FRONT DOOR w/ (2) DRAW Keyhole concentric conduit knockout PLUS A KEY LOCKING LATCH w/ DUST COVER Mounting RACK SPACES: 19" EIA 310-D COMPLIANT - SEELATCHES CHART FOR RMU 21.25 A-12 WALL MOUNT 2.50 A
DRAWING NOT TO SCALE
TOLERANCE UNLESS OTHERWISE NOTED: ANGULAR +/- 1~ .XXXX +/- .010 .XXX +/- .015 .XX +/- .030 .X FOR REF. ONLY
THIRD ANGLE PROJECTION
6
5
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES
4
CHECKED & APP.
3
10.63 Side View ESTED & CERTIFIED, NEMA-250-1997COLOR: TYPE 12.DURABLE BLACK TEXTURED POWDER COAT.
GREAT LAKES CASE & CABINET CO., INC.
A
P.O. BOX 551 EDINBORO, PA 16412 PHONE (814) 734-7303 FAX (814) 734-3907 E-MAIL
[email protected]
DWG NO:
REV
SHEET: 1 OF 1
DATE
2
1
10.63
REAR BOTTOM CABLE ACCESS FOR 1", 2", 3" CONDUIT SIZES
Side Ventilation
1", 2" and 3" rear section 21.25 D COMPLIANT - SEE CHART FOR RMUCONSTRUCTION: #12-24 THREADED MOUNTING RAILS, #12 GA. 2.50 nominal concentric conduit 10.63 10.63 #14 GA. CENTER BODY, # 16 GA.knockout FRONT DOOR. and horseshoe knockoutCABLE ACCESS REAR BOTTOM EXTURED POWDER COAT. ACCEPTS 1", 2", 3" CONDUIT SIZES FOR21.25 CABLE ACCESS. 2.50 10.63 10.63 FOR 1", 2", 3" CONDUIT SIZES FRONT DOOR & REAR SECTION LOCK INDEPENDENTLY.
READED MOUNTING RAILS, #12 GA. NTER BODY, # 16 GA. FRONT DOOR. "A" H PART ", 2", 3" CONDUIT SIZES FOR CABLE ACCESS. OR & REAR SECTION "A" LOCK INDEPENDENTLY.
HEIGHT 24" 36" 48"
# RMU 12 19 26
NUMBER GL240N12 "A" WT CAPACIT GL360N12 SHPG WT GL480N12 150 LBS 105 LBS 250 LBS 16.00 300 LBS 18.31 16.00 18.3121.25 21.25
W
140 LBS 175 LBS
16.00 18.31 21.25
(H) - HEIGHT 24" 36" 48"
# RMU 12 19 26
WT CAPACIT 150 LBS 250 LBS 300 LBS
5.00 BOTTOM VIEW
D
"B"
"C"
"B"
"B"
"C"
"C"
5.00
5.00
Top/Bottom View
Note: 2WT Fan unit SHPG mounting shown 105GL24WM, LBS for GL36WM, 140 LBS and GL48WM. Fan 175 LBS unit mounting rotated 90 degrees on GL2418WM.
BOTTOM VIEW
CENTER SECT A
CENTER SECTION SECURED BY OVER-CENTER LATCHES AND A KEY-LOCKING LATCH w/ DUST COVER
4 9
WD Series Wall MOunt Enclosure
NEMA 12 Wall Mount Enclosures RMU 12 19 26
.500 .625 .625
Part No. H GL240N12 24.00" 1.750 (1 RMU) PATTERN REPEATS GL360N12 36.00" GL480N12 48.00"
12-24 UNC - 2B EQUIPMENT MTG HOLES IN 12 GA RAILS. Instructions: 19" EIA 310-D COMPLIANT
Wt. Cap. 150 lbs 250 lbs 300 lbs
1. Mounting holes are designed for 1/4" hardware, 16.00" on center. SHIP. WT. 2. See detail “B” to remove pins for mounting back section to the wall 105 lbs REAR TOP CABLE ACCESS (make sure to reinstall back pin after wall mounting) FOR 1", 2", 3" CONDUIT 140 lbs 3. WSSIZES and WD handles can be found in the hardware bag. 175 lbs Front View
DETAILThe B
enclosure has been fully assembled at the factory, all you need to do is mount it to the wall. The mounting holes on this wall mount are designed for 1/4" SIDE CABLE ACCESS hardware, 16" on center. Internal rails are adjustable every 1". FOR 1", 2", 3" CONDUIT SIZES
Side View
TOP VIEW 24.000
4.327
9.000
REA
FRONT - ISO
REAR TOP CABLE ACCESS FOR 1", 2", 3" CONDUIT SIZES
1/4" LAG SCREWS RECOMMENDED
FOR MOUNTING INTO WALL STUDS Rear View
(H + 2.50) TO
12-24 UNC - 2B EQUIPMENT MTG HOLES IN 12 GA RAILS. 19" EIA 310-D COMPLIANT
H
B
24.000
GLAND PLATES CAN BE REMOVED TO ADD OPTIONAL FANS OR FILTERS
Side Cable SIDE CABLE ACCESS Access For 1", 2", 3" FOR 1", 2", 3" CONDUIT SIZES Conduit Sizes
(H + 6.00)
.625 .625
24.000 1.750 (1 RMU)A PATTERN REPEATS
TOP VIEW 24.000
4.327
Top/Bottom View 1", 2", 3" and 4" rear section nominal concentric conduit knockout
HINGED CENTER SECTION OF 14 GA CONSTRUCTION
9.000
REAR - I
FRONT - ISO
A
B
1/4" LAG SCREWS RECOMMENDED
FOR MOUNTING INTO WALL STUDS
.280 TYP
2 WALL MOUNT
concentric conduit knockout
(H + 6.00)
H
FRONT VIEW
Detail GLANDBPLATES CAN BE REMOVED SECTION A-A 1", 2", 3" and VIEW) 4" nominal TO ADD OPTIONAL FANS OR FILTERS (RIGHT SIDE
RIGHT SIDE VIEW
(H + 2.50) TO
A
16.000 TO
SOLID HINGED 16 GA FRONT DOOR w/ (2) DRAW LATCHES PLUS A KEY LOCKING LATCH w/ DUST COVER
HINGED CENTER SECTION DETAIL B OF 14 GA CONSTRUCTION SCALE 1
CENTER SWING SECTION
MPLIANT - SEE CHART FOR RMU
REAR BOTTOM CABLE ACCESS LOCK PIN SCREW FOR 1", 2", 3" CONDUIT SIZES
RED POWDER COAT.
IGHT
B
DETAIL B SCALE 1
ED & CERTIFIED, NEMA-250-1997 TYPE 12.
DED MOUNTING RAILS, #12 GA. .280 TYP R BODY, # 16 GA. FRONT A DOOR. 3" CONDUIT SIZES FOR CABLE ACCESS. TO REAR SECTION 16.000 LOCK INDEPENDENTLY.
Fan knockouts for 7217Ws assembly located on top and bottom
REAR SECTION
LOCK PIN BRACKET
RIGHT SIDE VIEW
SECTION A-A SIDE VIEW)
NYLON SHOULDER (RIGHT WASHER
REAR SECTION SUPPORT PLATE
CENTER SWING SECTION
LOCK PIN SCREW LOCK PIN BRACKET
REAR SECTION NYLON SHOULDER WASHER REAR SECTION SUPPORT PLATE HINGE PIN
# RMU WT CAPACIT SHPG WT 8 5 FRONT VIEW HINGE PIN 12
150 LBS
105 LBS
SOLID HINGED 16 GA FRONT DOOR w/ (2) DRAW
15WM Series Wall MOunt
WE Series Wall MOunt Enclosure
CONSTRUCTION:
FULLY WELDED MAIN BODY.
DURABLE TEXTURE 1. Unscrew specialty torxPOWDER screwCOAT using the supplied torx screw bit. Fig 1 (A) #12 GA. C.R.S. EQUIPMENT MTG. RAIL, (1 PAIR) 2. Remove back panel from wall mount. Fig 1 #16 GA. C.R.S. REAR WALL PLATE # 20 GA.panel C.R.S. MAIN BODY & DOOR. 3. Mount back to wall using ¼" hardware, 16" on center. 4. Once back panel is mounted, hang main body on mounted back panel. Fig 1 (B) 5. Secure main body using torx screw (keep screw in safe place for future use). Note: Push down tabs (Detail A ) to get one RMU mounting on the back panel.
1. Mounting holes are designed for 1/4" hardware, 16.00" on center. 2. Wall Mount must be mounted to three wall studs to achieve maximum weight capacity. 4
3
2
1
Mesh Doors with lock (quantity 2)
D
TORX DRIVE SECURITY SCREWS
A A
B
Figure 1
C
KEYED LOCK FOR FRONT DOOR
"SPARE" 1 RMU MOUNTING TABS SHOWN EXTENDED
1/2" & 3/4" CONDU
Fan Assembly Provision (7217WS)
CONSTRUCTION:
INside Veiw
B
INTERPRET DRAWING PER ASME Y14.5M-1994 DIMENSIONAL LIMITS APPLY AFTER APPLICATION OF FINISH DRAWING NOT TO SCALE
TOLERANCE UNLESS OTHERWISE NOTED: ANGULAR +/- 1~ .XXXX +/- .010 .XXX +/- .015 .XX +/- .030 .X FOR REF. ONLY
Top View THIRD ANGLE PROJECTION
3
NOTICE:
PART NUMBER:
18.31 16.00
CHECKED & APP.
DATE
EXHAUS 75 CFM TYP. TO TITLE
#10-32 TAPPED EIA MTG. HOLES A
24"H x 36"W x 20.5"D SERVER WALL MOUNT ASSEMBLY
GREAT LAKES CASE & CABINET CO., INC. P.O. BOX 551 EDINBORO, PA 16412 PHONE (814) 734-7303 FAX (814) 734-3907 E-MAIL
[email protected]
DWG NO:
REV
5
SHEET: 1 OF 1
Top Veiw
2
1
1/2" & 3/4" CONDUIT KNOCKOUTS 1" & 1 1/2" CONDUIT KNOCKOUTS
Detail A DETAIL A
5/8" KNOCKOUT
12.25 7 RMU
4
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES
Mounting holes for 1/4" hardware
I003909 catalog2 Use of this document is subject to QTY PER UNIT: 1 MATERIAL TYPE: a confidentiality and nondisclosure agreement with Great Lakes Case MATERIAL GAUGE: & Cabinet Co., Inc. (GLCC) and may FINISH: not be reproduced, disclosed or utilized in whole or in part without DRAWN DATE 4/19/2006 prior written authorization from GLCC. JAL
5/8" KNOCK
12.25 7 RMU
16.00
1", 2" and 3" nominal concentric conduit knockout; Typ. 3 top & bottom Typ. 3 rear
1" & 1 1/2" CON
FULLY WELDED MAIN BODY. DURABLE TEXTURE POWDER COAT #12 GA. C.R.S. EQUIPMENT MTG. RAIL, (1 PAIR) #16 GA. C.R.S. REAR WALL PLATE # 20 GA. C.R.S. MAIN BODY & DOOR.
18.31
EXHAUST FAN KNOCKOUT 75 CFM - 110VAC TYP. TOP & BOTTOM. #10-32 TAPPED EIA MTG. HOLES Rear View
6 7
15WM Series Wall MOunt
WE Series Wall MOunt Enclosure
CONSTRUCTION:
FULLY WELDED MAIN BODY.
DURABLE TEXTURE 1. Unscrew specialty torxPOWDER screwCOAT using the supplied torx screw bit. Fig 1 (A) #12 GA. C.R.S. EQUIPMENT MTG. RAIL, (1 PAIR) 2. Remove back panel from wall mount. Fig 1 #16 GA. C.R.S. REAR WALL PLATE # 20 GA.panel C.R.S. MAIN BODY & DOOR. 3. Mount back to wall using ¼" hardware, 16" on center. 4. Once back panel is mounted, hang main body on mounted back panel. Fig 1 (B) 5. Secure main body using torx screw (keep screw in safe place for future use). Note: Push down tabs (Detail A ) to get one RMU mounting on the back panel.
1. Mounting holes are designed for 1/4" hardware, 16.00" on center. 2. Wall Mount must be mounted to three wall studs to achieve maximum weight capacity. 4
3
2
1
Mesh Doors with lock (quantity 2)
D
TORX DRIVE SECURITY SCREWS
A A
B
Figure 1
C
KEYED LOCK FOR FRONT DOOR
"SPARE" 1 RMU MOUNTING TABS SHOWN EXTENDED
1/2" & 3/4" CONDU
Fan Assembly Provision (7217WS)
CONSTRUCTION:
INside Veiw
B
INTERPRET DRAWING PER ASME Y14.5M-1994 DIMENSIONAL LIMITS APPLY AFTER APPLICATION OF FINISH DRAWING NOT TO SCALE
TOLERANCE UNLESS OTHERWISE NOTED: ANGULAR +/- 1~ .XXXX +/- .010 .XXX +/- .015 .XX +/- .030 .X FOR REF. ONLY
Top View THIRD ANGLE PROJECTION
3
NOTICE:
PART NUMBER:
18.31 16.00
CHECKED & APP.
DATE
EXHAUS 75 CFM TYP. TO TITLE
#10-32 TAPPED EIA MTG. HOLES A
24"H x 36"W x 20.5"D SERVER WALL MOUNT ASSEMBLY
GREAT LAKES CASE & CABINET CO., INC. P.O. BOX 551 EDINBORO, PA 16412 PHONE (814) 734-7303 FAX (814) 734-3907 E-MAIL
[email protected]
DWG NO:
REV
5
SHEET: 1 OF 1
Top Veiw
2
1
1/2" & 3/4" CONDUIT KNOCKOUTS 1" & 1 1/2" CONDUIT KNOCKOUTS
Detail A DETAIL A
5/8" KNOCKOUT
12.25 7 RMU
4
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES
Mounting holes for 1/4" hardware
I003909 catalog2 Use of this document is subject to QTY PER UNIT: 1 MATERIAL TYPE: a confidentiality and nondisclosure agreement with Great Lakes Case MATERIAL GAUGE: & Cabinet Co., Inc. (GLCC) and may FINISH: not be reproduced, disclosed or utilized in whole or in part without DRAWN DATE 4/19/2006 prior written authorization from GLCC. JAL
5/8" KNOCK
12.25 7 RMU
16.00
1", 2" and 3" nominal concentric conduit knockout; Typ. 3 top & bottom Typ. 3 rear
1" & 1 1/2" CON
FULLY WELDED MAIN BODY. DURABLE TEXTURE POWDER COAT #12 GA. C.R.S. EQUIPMENT MTG. RAIL, (1 PAIR) #16 GA. C.R.S. REAR WALL PLATE # 20 GA. C.R.S. MAIN BODY & DOOR.
18.31
EXHAUST FAN KNOCKOUT 75 CFM - 110VAC TYP. TOP & BOTTOM. #10-32 TAPPED EIA MTG. HOLES Rear View
6 7
WD Series Wall MOunt Enclosure
NEMA 12 Wall Mount Enclosures RMU 12 19 26
.500 .625 .625
Part No. H GL240N12 24.00" 1.750 (1 RMU) PATTERN REPEATS GL360N12 36.00" GL480N12 48.00"
12-24 UNC - 2B EQUIPMENT MTG HOLES IN 12 GA RAILS. Instructions: 19" EIA 310-D COMPLIANT
Wt. Cap. 150 lbs 250 lbs 300 lbs
1. Mounting holes are designed for 1/4" hardware, 16.00" on center. SHIP. WT. 2. See detail “B” to remove pins for mounting back section to the wall 105 lbs REAR TOP CABLE ACCESS (make sure to reinstall back pin after wall mounting) FOR 1", 2", 3" CONDUIT 140 lbs 3. WSSIZES and WD handles can be found in the hardware bag. 175 lbs Front View
DETAILThe B
enclosure has been fully assembled at the factory, all you need to do is mount it to the wall. The mounting holes on this wall mount are designed for 1/4" SIDE CABLE ACCESS hardware, 16" on center. Internal rails are adjustable every 1". FOR 1", 2", 3" CONDUIT SIZES
Side View
TOP VIEW 24.000
4.327
9.000
REA
FRONT - ISO
REAR TOP CABLE ACCESS FOR 1", 2", 3" CONDUIT SIZES
1/4" LAG SCREWS RECOMMENDED
FOR MOUNTING INTO WALL STUDS Rear View
(H + 2.50) TO
12-24 UNC - 2B EQUIPMENT MTG HOLES IN 12 GA RAILS. 19" EIA 310-D COMPLIANT
H
B
24.000
GLAND PLATES CAN BE REMOVED TO ADD OPTIONAL FANS OR FILTERS
Side Cable SIDE CABLE ACCESS Access For 1", 2", 3" FOR 1", 2", 3" CONDUIT SIZES Conduit Sizes
(H + 6.00)
.625 .625
24.000 1.750 (1 RMU)A PATTERN REPEATS
TOP VIEW 24.000
4.327
Top/Bottom View 1", 2", 3" and 4" rear section nominal concentric conduit knockout
HINGED CENTER SECTION OF 14 GA CONSTRUCTION
9.000
REAR - I
FRONT - ISO
A
B
1/4" LAG SCREWS RECOMMENDED
FOR MOUNTING INTO WALL STUDS
.280 TYP
2 WALL MOUNT
concentric conduit knockout
(H + 6.00)
H
FRONT VIEW
Detail GLANDBPLATES CAN BE REMOVED SECTION A-A 1", 2", 3" and VIEW) 4" nominal TO ADD OPTIONAL FANS OR FILTERS (RIGHT SIDE
RIGHT SIDE VIEW
(H + 2.50) TO
A
16.000 TO
SOLID HINGED 16 GA FRONT DOOR w/ (2) DRAW LATCHES PLUS A KEY LOCKING LATCH w/ DUST COVER
HINGED CENTER SECTION DETAIL B OF 14 GA CONSTRUCTION SCALE 1
CENTER SWING SECTION
MPLIANT - SEE CHART FOR RMU
REAR BOTTOM CABLE ACCESS LOCK PIN SCREW FOR 1", 2", 3" CONDUIT SIZES
RED POWDER COAT.
IGHT
B
DETAIL B SCALE 1
ED & CERTIFIED, NEMA-250-1997 TYPE 12.
DED MOUNTING RAILS, #12 GA. .280 TYP R BODY, # 16 GA. FRONT A DOOR. 3" CONDUIT SIZES FOR CABLE ACCESS. TO REAR SECTION 16.000 LOCK INDEPENDENTLY.
Fan knockouts for 7217Ws assembly located on top and bottom
REAR SECTION
LOCK PIN BRACKET
RIGHT SIDE VIEW
SECTION A-A SIDE VIEW)
NYLON SHOULDER (RIGHT WASHER
REAR SECTION SUPPORT PLATE
CENTER SWING SECTION
LOCK PIN SCREW LOCK PIN BRACKET
REAR SECTION NYLON SHOULDER WASHER REAR SECTION SUPPORT PLATE HINGE PIN
# RMU WT CAPACIT SHPG WT 8 5 FRONT VIEW HINGE PIN 12
150 LBS
105 LBS
SOLID HINGED 16 GA FRONT DOOR w/ (2) DRAW
REV
.500 .625 .625
WM Series Wall MOunt Enclosure
DESCRIPTION
DATE 9/23/2010
APPROVED WSS
D
1.750 (1 RMU) PATTERN REPEATS
REAR TOP CABLE ACCESS FOR 1", 2", 3" CONDUIT SIZES
1. Mounting holes are designed for 1/4" hardware, 12-24 16.00" on- 2B center. UNC EQUIPMENT
MTG HOLES IN 12 GA RAILS.
C
REAR TOP CABLE ACCESS FOR 1", 2", 3" CONDUIT SIZES
Rear section
TOP VIEW
Option: 2, Fan unit ventilation 12-24 UNC - 2B EQUIPMENT top or bottom mounting MTG HOLES IN 12 GA RAILS. 19" EIA 310-D COMPLIANT Center swing section
DETAIL B
B
19" EIA Rack spaced 2 pair mounting rails tapped #12-24
TOP VIEW
1", 2" and 3" nominal concentric 24.000 conduit knockouts and horseshoe A knockouts; top & bottom rear section SIDE CABLE ACCESS Continuous Hinges on front door & rear4.327 section
17.86 H (H + 2.50) TO
(# RMU) H
6
5
4
D
Part No. H W D GL2418WM 24.00" 21.25" 18.00" GL24WM 24.00" 21.25" 24.50" GL36WM 36.00" FRONT 21.25" 24.50" VIEW w/ DOOR REMOVED24.50" GL48WM 48.00" 21.25"
FOR MOU
REAR - ISO
FRONT - ISO
GLAND PLATES CAN TO ADD OPTIONAL FAN
1/4" LAG SCREWS RECOMMENDED
GLAND PLATES CAN BE REMOVED TO ADD OPTIONAL FANS OR FILTERS 8
7
6
5
REAR SECTION OF 14 GA CRSCENTER SEC HINGED CONSTRUCTION OF 14 GA CONSTRUC 4
3
HINGED CENTER SECTION OF 14 GA CONSTRUCTION
.280 TYP SECTION A-A
RIGHT 16 SIDE Solid Hinged GA VIEW front (RIGHT SIDE VIEW) door w/(2) Draw Latches plus key locking latch w/dust cover SECTION A-A SOLID HINGED 16 GA FRONT DOOR w/ (2) DRAW (RIGHT SIDE VIEW) C
FRONT VIEW
B
DETAIL B
LATCHES PLUS A KEY LOCKING LATCH w/ DUST COVER
DETAIL A
DIMENSIONAL LIMITS APPLY AFTER APPLICATION OF FINISH
1/4" LAG
1
Front View SPECIFICATIONS: NEMA-12 WALL MOUNT Use latch supplied in hardware bag, FRONTRATING VIEW : INDEPENDENTLY TESTED & CERTIFIED, when horseshoe knockout is used NEMA-250-1997 TYPE 12. 1", 2" and 3" rear section nominal INTERPRET DRAWING PER ASME Y14.5M-1994
FRONT
FOR MOUNTING INTO WALL STUDS
D
RIGHT SIDE VIEW
B
9.000
Neoprene Gasket
A
2
16.000 TO
.280 TYP
A
3
A
C
16.000 TO
4.327
9.000
(H + 2.50) TO
Independent locking front 18.312 TO A door & rear section
24.000 B
FOR 1", 2", 3" CONDUIT SIZES
24.000
24.000
Front door
SIDE CABLE ACCESS FOR 1", 2", 3" CONDUIT SIZES
TOP VIEW
(H + 6.00)
PATTERN REPEATS
(H + 6.00)
.500 .625 .625
2. Use the template on the shipping box to locate your mounting holes. 19" EIA 310-D COMPLIANT (WM & WS only) 1.750 (1 RMU) DETAIL B
NOTICE:
PART NUMBER:
cable latch detail Use of this document is subject to QTY PER UNIT: 1 MATERIAL TYPE: a confidentiality and nondisclosure agreement with Great Lakes Case MATERIAL GAUGE: & Cabinet Co., Inc. (GLCC) and may FINISH: not be reproduced, disclosed or utilized in whole or in part without DRAWN DATE 10/5/2007 prior written authorization from GLCC. ANDY
TITLE
SOLID HINGED 16 GA FRONT DOOR w/ (2) DRAW Keyhole concentric conduit knockout PLUS A KEY LOCKING LATCH w/ DUST COVER Mounting RACK SPACES: 19" EIA 310-D COMPLIANT - SEELATCHES CHART FOR RMU 21.25 A-12 WALL MOUNT 2.50 A
DRAWING NOT TO SCALE
TOLERANCE UNLESS OTHERWISE NOTED: ANGULAR +/- 1~ .XXXX +/- .010 .XXX +/- .015 .XX +/- .030 .X FOR REF. ONLY
THIRD ANGLE PROJECTION
6
5
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES
4
CHECKED & APP.
3
10.63 Side View ESTED & CERTIFIED, NEMA-250-1997COLOR: TYPE 12.DURABLE BLACK TEXTURED POWDER COAT.
GREAT LAKES CASE & CABINET CO., INC.
A
P.O. BOX 551 EDINBORO, PA 16412 PHONE (814) 734-7303 FAX (814) 734-3907 E-MAIL
[email protected]
DWG NO:
REV
SHEET: 1 OF 1
DATE
2
1
10.63
REAR BOTTOM CABLE ACCESS FOR 1", 2", 3" CONDUIT SIZES
Side Ventilation
1", 2" and 3" rear section 21.25 D COMPLIANT - SEE CHART FOR RMUCONSTRUCTION: #12-24 THREADED MOUNTING RAILS, #12 GA. 2.50 nominal concentric conduit 10.63 10.63 #14 GA. CENTER BODY, # 16 GA.knockout FRONT DOOR. and horseshoe knockoutCABLE ACCESS REAR BOTTOM EXTURED POWDER COAT. ACCEPTS 1", 2", 3" CONDUIT SIZES FOR21.25 CABLE ACCESS. 2.50 10.63 10.63 FOR 1", 2", 3" CONDUIT SIZES FRONT DOOR & REAR SECTION LOCK INDEPENDENTLY.
READED MOUNTING RAILS, #12 GA. NTER BODY, # 16 GA. FRONT DOOR. "A" H PART ", 2", 3" CONDUIT SIZES FOR CABLE ACCESS. OR & REAR SECTION "A" LOCK INDEPENDENTLY.
HEIGHT 24" 36" 48"
# RMU 12 19 26
NUMBER GL240N12 "A" WT CAPACIT GL360N12 SHPG WT GL480N12 150 LBS 105 LBS 250 LBS 16.00 300 LBS 18.31 16.00 18.3121.25 21.25
W
140 LBS 175 LBS
16.00 18.31 21.25
(H) - HEIGHT 24" 36" 48"
# RMU 12 19 26
WT CAPACIT 150 LBS 250 LBS 300 LBS
5.00 BOTTOM VIEW
D
"B"
"C"
"B"
"B"
"C"
"C"
5.00
5.00
Top/Bottom View
Note: 2WT Fan unit SHPG mounting shown 105GL24WM, LBS for GL36WM, 140 LBS and GL48WM. Fan 175 LBS unit mounting rotated 90 degrees on GL2418WM.
BOTTOM VIEW
CENTER SECT A
CENTER SECTION SECURED BY OVER-CENTER LATCHES AND A KEY-LOCKING LATCH w/ DUST COVER
4 9
Wall Mount AcCESSORIES PART NO. DESCRIPTION WM 3 7206-FM* Stationary Front Mount q Shelf 18"D, Wt Cap. 60 lbs. 3 7206-EIA* Stationary Shelf q 18"D, Wt Cap. 80 lbs.
WS WD WE NEMA 3 3 q 3 q q q 3 q
3 q
3 q q
7206-14
3 q
q
3 q
3 q q
3 q
3 q
3 q
3 q q
7206-FR-AHD Stationary Shelf front & q rear mount, adjustable 22.25"D, Wt Cap. 200 lbs.
q
3 q
q q
7206-SL*
3 q
3 q
3 q q
Stationary Shelf 14"D, Wt Cap. 60 lbs.
7206-FR-A18* Stationary Shelf front & rear mount, adjustable 18"D, Wt Cap. 150 lbs.
Sliding Shelf 16.343"W x 17.50"D Wt Cap. 40 lbs.
7206-FRSL-AHD Sliding Shelf front & rear mount sliding, (adj.) 22"D, Wt Cap. 110 lbs.
3 q
3 q
3 q
3 q
3 q q
3 q
3 q
3 3 q q
3 q
3 q
3 3 q q
7219-20AR
3 6 position Power Strip q 15 ft. cord for 19" mounting 3 Rack mount 14 position q (6 front/8 back) Power Strip with surge suppressor 3 6 position Power Strip with q curcuit breaker (20 amp)
7217WS
3 Fan Assembly with fan q guards and (2) 75 CFM fans
3 q
3 q
3 q q
7208WS/WD
Casters, 3 locking and 3 non-locking, 3.625"H
q
3 q
3 q
q q
CBB-19
Copper Bus Bar 19" rack mounted (isolated)
3 q
3 q
3 q
3 3 q q
GR102
Grounding Kit
3 q
3 q
3 q
q q
DK1
Dust Resistant Kit, q 4 cover plates, 4 fan filters and hardware
q
3 q
q q
7219 7219-SR14
Important Notes Regarding wall mount installation When installing a Great Lakes wall-mounted rack enclosure to materials such as wood, cinder block, concrete, etc., please consider the load capacity within the wall mount structure, and be certain to check with local authorities to determine the appropriate hardware requirements for these conditions. Because wall compositions may vary at different installation sites, Great Lakes cannot warrant the fitness or suitability of any installation instructions or installation hardware it may provide for wall-mount rack enclosures. Great Lakes recommends that an experienced maintenance and/or technical person be consulted regarding the proper wallmounting hardware and procedures to be used for the anticipated load capacity of the wallmounted rack enclosure. Maximum weight capacity determined at minimal deflection. (Deflection chart available upon request.) Make sure enclosure is secured and squared on mounting surface. Improper installation will cause excessive deflection.
WS Series Wall MOunt/ SWing Out Enclosure 1. Mounting holes are designed for 1/4"hardware, 16" on center. 2. Use the template on the shipping box to locate your mounting holes. (WM & WS only) 3. WS and WD handles can be found in the hardware bag. 1", 2", 3" and 4" nominal concentric conduit knockouts 24"
Part No. H W D GL24WS 24.00" 24.00" 24.00" GL36WS 36.00" 24.00" 24.00" GL48WS 48.00" 24.00" 24.00"
Fan assembly provisions Optional caster mounting holes
3 q
3 q
3 q 3 q
24" Two pair 19" EIA rails provided with each enclosure
Mounting holes for 1/4" hardware, 16.00" centers
H
Side View
Side View
Front View
Rear View
10 3
Wall Mount AcCESSORIES PART NO.
DESCRIPTION
WM WS WD WE NEMA
DK2*
Dust Resistant Kit, 4 cover plates, 4 fan filters and hardware
3 q
q
q
q q
FFK1
Four Fan Filters
3 q
3 q
3 q
q q
3 HDW-104-50 Package of 50 Pan Head q Phillips #12-24 x 1/2" screws Type 23, Black
3 q
3 q
q q
WS-22
3 q
3 q
3 q q
66/110 Block Mounting Panel
3 q
* Will not fit GL2418WM
Thank you for your business!
When installing a Great Lakes wall-mounted rack enclosure to materials such as wood, cinder block, concrete, etc., please consider the load capacity within the wall mount structure, and be certain to check with local authorities to determine the appropriate hardware requirements for these conditions. Because wall compositions may vary at different installation sites, Great Lakes cannot warrant the fitness or suitability of any installation instructions or installation hardware it may provide for wall-mount rack enclosures. Great Lakes hereby DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THE SUFFICIENCY, FITNESS OR SUITABILITY OF ANY INSTALLATION INSTRUCTIONS OR INSTALLATION HARDWARE GREAT LAKES MAY PROVIDE FOR WALL-MOUNTED ENCLOSURES. Great Lakes recommends that an experienced maintenance and/or technical person be consulted regarding the proper wall-mounting hardware and procedures to be used for the anticipated load capacity of the wall-mounted rack enclosure. Product specifications are subject to change without prior notice.
Great Lakes Case & Cabinet Co., Inc. P.O. Box 551 • Edinboro, PA 16412 1-866-TRY-GLCC • (1-866-879-4522) Phone: 814.734.7303 Fax: 814.734.3907
WeRackYourWorld.com 11
WM, WD, WS, WE, 15WM & NEMA Series Wall Mounts
Thank you for your business!
Installation Instructions
WDS
ISO 9001 : 2008
WM
ETSI Associate Member
WeRackYourWorld.com MS-5.02-10 Rev.2
1-866-TRY-GLCC (879-4522)
