Transcript
Specification sheet Grande Pendant COLOUR CHANGING
Front view
Bottom view
Photometric Summary
Description Dummy
The Lumenbeam Grande Pendant Colour Changing is a highperformance, 100-watt luminaire for applying dynamic colour to mid- or high-ceiling applications such as auditoriums, transport terminals and public atriums. It has numerous options including optics for flood or accent lighting; a RGB, RGBW or RGBA colour mixing; various stem lengths, accessories and spread lenses; and control via DMX/RDM or Lumentalk.
Features Optics
Colour and Colour Temperature
Additive RGB, Additive RGB + white 4000K, Additive RGB + amber
Mounting Length
12 in, 24 in, 36 in, 48 in
Optics
6°, 10°, 20°, 40°, 60°
Optical Option
Linear spread lens horizontal distribution, Linear spread lens vertical distribution
Options
Corrosion-resistant coating for hostile environments
Power Consumption
100 W
Warranty
5-year limited warranty
Control
Rating
Performance Delivered Output
3,716 lm (RGB full output, VN optic), 3,328 lm (RGBW full output, VN optic), 2,522 lm (RGBA full output, VN optic)
Delivered Intensity
134,713 cd at nadir (RGB full output, VN optic), 190,032 cd at nadir (RGBW full output, VN optic), 126,585 cd at nadir (RGBA full output, VN optic)
Colour Consistency
2 SDCM
Lumen Maintenance
L70 120,000 hrs (Ta 25 °C)
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 1 / 12
Specification sheet Grande Pendant COLOUR CHANGING
Physical Housing Material
Low copper content high pressure die-cast aluminium
Lens Material
Clear tempered glass
Hardware Material
Stainless steel
Gaskets
Silicone
Surface Finish
Electrostatically applied polyester powder coat
Weight
22 lbs
EPA
Side = 0.75 sq ft
Electrical and control Voltage
100 to 277 volts
Fixture Cable
Power and data cable goes through stem
Inrush Current (peak)
55A @230VAC
Resolution (DMX/RDM)
Per board or fixture (configured with LumenID V3 software), 8-bit or 16-bit, 3 channels (RGB) or 4 channels (RGBW, RGBA)
RGB Colour Mixing
72 LEDs (12x Red, 12x Green, 12x Blue per board)
RGBW Colour Mixing
48 LEDs (6x Red, 6x Green, 6x Blue, 6x White 4000K per board)
RGBA Colour Mixing
48 LEDs (6x Red, 6x Green, 6x Blue, 6x Amber per board)
Control
Lumentalk, DMX/RDM enabled
Environmental Operating Temperature
-13 °F to 122 °F
IP Rating
IP66 fixture, IP54 canopy (suitable for wet location, not suitable for water jet)
IK Rating
IK09
Accessories (order separately) Control Boxes
Power and control box - daisy chain configuration, Power and control box - star configuration
Control Systems
Lumentouch 2.0™, Lumencue, Pharos® TPC, Pharos® LPC X, Pharos® LPC
Diagnostic and Addressing Tools
LumenID, LumentalkID
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 2 / 12
Specification sheet Grande Pendant COLOUR CHANGING
Mounting types SCAN - Standard straight stem canopy
ACAN - Adjustable sloped ceiling canopy
Optical options LSLH - Linear spread lens horizontal distribution LSLV - Linear spread lens vertical distribution
Factory installed, not adjustable on site. Not available for WFL optic. See 'Optical Accessories' section for field adjustable spread lens (LSLA).
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 3 / 12
Specification sheet Grande Pendant COLOUR CHANGING
Optical accessories (order separately) SN - Snoot
SNW - Snoot Wide
LBGSN-FINISH-BK Interior surface painted black. Please specify desired exterior FINISH from list of available finishes.
LBGSNW-FINISH-BK Interior surface painted black. Please specify desired exterior FINISH from list of available finishes.
VS - Visor
LSLA - Linear Spread Lens Adjustable
LBGVS-FINISH-BK Interior surface painted black. Please specify desired exterior FINISH from list of available finishes.
LBGLSLA-FINISH Please specify desired exterior FINISH from list of available finishes.
WG - Wire Guard
Accessory combinations
LBGWG-FINISH Please specify desired exterior FINISH from list of available finishes.
Accessory combinations must be ordered together on a single line Ex: A Snoot + Wire Guard combination order code is LBGSNWG-BK-BK.
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 4 / 12
Specification sheet Grande Pendant COLOUR CHANGING
Available exterior finishes for optical accessories BK - Black Sandtex® BRZ - Bronze Sandtex® SI - Silver Sandtex® WH - Smooth white BKTX - Textured black BRZTX - Textured bronze, non-metallic GRATX - Textured medium grey GRNTX - Textured green WHTX - Textured white CC - Custom colour and finish (please specify RAL colour)* *Lumenpulse offers a wide selection of RAL CLASSIC (K7) colours with a smooth texture and high-gloss finish. Please consult factory for a list of available K7 colours, other RAL textures and glosses, or to match alternate colour charts. Final colour matching results may vary.
Resolution details Resolution per board: each board is addressed independently DMX addresses:
RGB colour mixing option
RGBW, RGBA colour mixing options
Resolution per fixture: each fixture is addressed independently DMX addresses:
RGB colour mixing option
RGBW, RGBA colour mixing options
Fixture resolution can be configured on-site within the LumenID V3 software. A DMX/RDM enabled CBX is required.
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 5 / 12
Specification sheet Grande Pendant COLOUR CHANGING
Typical wiring diagrams Wiring colour code
Lumentalk (LT) A - Third party DMX/RDM controller B - Lumentranslator (LTL-DMX) C - Data wiring (by others) D - Power line (120-277V AC) E - Junction box (by others) F - Power wiring (by others) G - Lumenbeam Grande Pendant Lumentalk (LT) - wiring detail A - Power input (control over power line via Lumentalk system) or from previous fixture B - To fixture C - To next fixture D - Live E - Ground F - Neutral G - Terminal connector (by others) H - Junction box (by others) Consult factory for specific applications and maximum fixture count/cable length recommendations. Lumentalk enabled fixtures must be commissioned using LumentalkID software and a LID-LT. Consult factory for details. Maximum of 1 transmitter (Lumentranslator or Lumenlink) per system. No third party fixtures allowed on the same circuit. 1 DMX controller per Lumentalk network, maximum of 48 DMX channels per Lumentalk network (minimum step transition update rate is 1 second, minimum fade time between two colours is 1 minute). Consult factory for applications that require additional capabilities. 100 watts per fixture.
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 6 / 12
Specification sheet Grande Pendant COLOUR CHANGING
Star Layout (DMX/RDM) A - Third party DMX/RDM controller B - Data input (Belden 9841 or equivalent, by others) C - Data output to next CBX (optional, not isolated/not boosted) D - CBX-ST E - Power input (100-277V) F - Power and data output to fixture (wiring by others) G - Junction box (by others) H - Lumenbeam Grande Pendant
Star Layout (DMX/RDM) - wiring detail - CE A - From CBX or previous fixture B - Lumenterminator* C - To fixture D - Data E - Data + F - Neutral G - Ground H - Live I - Terminal connector (by others) J - Junction box (by others) Star Layout (DMX/RDM) - wiring detail - CE Class II option A - From CBX or previous fixture B - Lumenterminator* C - To fixture D - Data E - Data + F - Neutral G - Signal common H - Live I - Terminal connector (by others) J - Junction box (by others)
Consult factory for specific applications and maximum fixture count/cable length recommendations. Run length calculations are based on a voltage drop of no more than 25V. The DMX/RDM protocol states a maximum of 32 DMX/RDM enabled fixtures on any single run. Maximum of 4 DMX/RDM repeaters/CBX cascading in line. Maximum of 6 outputs per CBX-ST. RGB colour mixture option requires 3 DMX addresses. RGBW colour mixture option requires 4 DMX addresses. RGBA colour mixture option requires 4 DMX addresses. 100 watts per fixture. * DMX terminator is required at the end of each run to maintain data integrity. (6x) DMX lumenterminators included per CBX-ST. See installation instructions for details.
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 7 / 12
Specification sheet Grande Pendant COLOUR CHANGING
Daisy Chain Layout (DMX/RDM) A - Third party DMX/RDM controller B - Data input (Belden 9841 or equivalent, by others) C - Data output to next CBX (optional, not isolated/not boosted) D - CBX-DS E - Power input (100-277V) F - Power and data output to fixture (wiring by others) G - Junction box (by others) H - Power and data wiring (by others) I - Lumenbeam Grande Pendant Daisy Chain Layout (DMX/RDM) - wiring detail (first or middle of run) - CE A - From CBX or previous fixture B - To fixture C - Data + D - Data E - To next/from previous fixture F - Live G - Ground H - Neutral I - Terminal connector (by others) J - Junction box (by others) Daisy Chain Layout (DMX/RDM) - wiring detail (end of run) - CE A - From CBX or previous fixture B - Lumenterminator* C - To fixture D - Data E - Data + F - Neutral G - Ground H - Live I - Terminal connector (by others) J - Junction box (by others) Daisy Chain Layout (DMX/RDM) - wiring detail (first or middle of run) - CE Class II option A - From CBX or previous fixture B - To fixture C - Data + D - Data E - To next/from previous fixture F - Live G - Signal common H - Neutral I - Terminal connector (by others) J - Junction box (by others)
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 8 / 12
Specification sheet Grande Pendant COLOUR CHANGING
Daisy Chain Layout (DMX/RDM) - wiring detail (end of run) - CE Class II option A - From CBX or previous fixture B - Lumenterminator* C - To fixture D - Data E - Data + F - Neutral G - Signal common H - Live I - Terminal connector (by others) J - Junction box (by others)
Consult factory for specific applications and maximum fixture count/cable length recommendations. Run length calculations are based on a voltage drop of no more than 25V. The DMX/RDM protocol states a maximum of 32 DMX/RDM enabled fixtures on any single run. Maximum of 4 DMX/RDM repeaters/CBX cascading in line. Maximum of 1 output per CBX-DS. Maximum 3 ft cable length recommended between fixture and next junction box for daisy chain layout. RGB colour mixture option requires 3 DMX addresses. RGBW colour mixture option requires 4 DMX addresses. RGBA colour mixture option requires 4 DMX addresses. 100 watts per fixture. * DMX terminator is required at the end of each run to maintain data integrity. (2x) DMX lumenterminators included per CBX-DS. See installation instructions for details.
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 9 / 12
Specification sheet Grande Pendant COLOUR CHANGING
Accessories (order separately) Control Boxes CBX-DS-Power and control box - daisy chain configuration
CBX-ST-Power and control box - star configuration
DMX/RDM control box. One power and data output to fixture or fixture run. Ethernet enabled option. Refer to CBX specification sheet for details.
DMX/RDM control box. Up to six power and data outputs to fixtures or fixture runs. Ethernet enabled option. Refer to CBX specification sheet for details.
Control Systems LTO2-Lumentouch 2.0™
LCU-Lumencue
Lumentouch is a wall mount DMX 512 controller keypad.
Lumencue is a USB / mini SD DMX 512 controller.
TPC-Pharos® TPC
LPC X-Pharos® LPC X
The Pharos Touch Panel Controller (TPC) is a wall-mounted DMX512 controller with a capacitive touch screen.
The Pharos Lighting Playback Controller X (LPC X) is designed for large-scale lighting installations and extremely complex lighting projects.
LPC-Pharos® LPC
The Pharos Lighting Playback Controller (LPC) is designed for small and mid-size lighting installations.
Diagnostic and Addressing Tools LID-LumenID
LID-LT-LumentalkID
LumenID is a diagnostic and addressing DMX/RDM tool. It must be specified on all DMX applications. Refer to LID specification sheet for details.
LumentalkID is a diagnostic and addressing tool. It must be specified for all Lumentalk (LT) applications. Refer to LID-LT specification sheet for details.
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 10 / 12
Specification sheet Grande Pendant COLOUR CHANGING
How to order
LBGP
1 . Housing LBGP
2 . Voltage Lumenbeam™ Grande Pendant
3 . Colour and Colour Temperature (1)
100
100 volts
120
120 volts
208
208 volts
220
220 volts
240
240 volts
277
277 volts
4 . Optic1
RGB
Additive RGB
VN
Very Narrow 6°
RGBW
Additive RGB + white 4000K
NS
Narrow Spot 10°
RGBA
Additive RGB + amber
NF
Narrow Flood 20°
FL
Flood 40°
WFL
Wide Flood 60° (2)
5 . Optic2
6 . Mounting Type
VN
Very Narrow 6°
SCAN
Straight stem canopy
NS
Narrow Spot 10°
ACAN
Adjustable sloped ceiling canopy
NF
Narrow Flood 20°
FL
Flood 40°
WFL
Wide Flood 60° (2)
8 . Optical Option
7 . Mounting Length (3) 12
12 in
24
24 in
36
36 in
48
48 in
9 . Finish
LSLH
Linear spread lens horizontal distribution (4)
BK
Black Sandtex®
LSLV
Linear spread lens vertical distribution (4)
BRZ
Bronze Sandtex®
SI
Silver Sandtex®
WH
Smooth white
BKTX
Textured black
BRZTX
Textured bronze non-metallic
GRATX
Textured medium grey
GRNTX
Textured green
WHTX
Textured white
CC
Custom colour and finish (please specify RAL colour) (5)
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 11 / 12
Specification sheet Grande Pendant COLOUR CHANGING
10 . Control
11 . Options
LT
Lumentalk (6) (7)
DMX/RDM
DMX/RDM enabled
CRC
Corrosion-resistant coating for hostile environments (8)
12 . Certification UL
UL compliant
CE
CE compliant
CEII
CE compliant Class II double insulated
Notes: (1) Consult factory for colour mix with Royal Blue, 3000K or other white colour temperature LEDs. (2) Cannot be combined with other optics. (3) Consult factory for custom stem lengths. (4) Not available for WFL optic. Factory installed. Field adjustable spread lens accessory available, order
separately. (5) Lumenpulse offers a wide selection of RAL CLASSIC (K7) colours with a smooth texture and high-gloss
finish. Please consult factory for a list of available K7 colours, other RAL textures and glosses, or to match alternate colour charts. Final colour matching results may vary. (6) A Lumentranslator and LumentalkID must be specified for Lumentalk applications. Consult
Lumentranslator and Lumentalk pages and specification sheets for details. (7) Not available with Class II double insulated option. (8) Use only when exposed to salt spray and harsh chemicals. This option is not required for normal
outdoor exposure.
11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370
[email protected] www.lumenpulsegroup.com
Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R10 12 / 12
