Specification Sheet

Transcript

Specification sheet Large Pendant DYNAMIC WHITE Front view Bottom view Photometric Summary Description Dummy The Lumenbeam Large Pendant Dynamic White is an IP66-rated suspended luminaire for general and accent lighting indoors or outdoors with a feature that enables the selection of any colour temperature from 2200K to 3000K or from 2700K to 6500K. This dynamic white feature gives designers and their clients the freedom to alter the ambience of a space in response to the time of day or the way a space is used. A number of other options are on offer: optics for flood or accent lighting; various stem lengths, accessories and spread lenses; and control via DMX/RDM, 0-10V or Lumentalk.​ The luminaire also has an anti-corrosion option for use in industrial, saline or coastal environments. Features Optics Control Rating Colour and Colour Temperature Dynamic warm white (2200K to 3000K), Dynamic white (2700K to 6500K) Mounting Length 305 mm, 610 mm, 914 mm, 1219 mm Optics 6°, 10°, 20°, 40°, 60° Optical Option Linear spread lens horizontal distribution, Linear spread lens vertical distribution Options Corrosion-resistant coating for hostile environments Power Consumption 50 W Warranty 5-year limited warranty Performance Illuminance at Distance Minimum 161.4 lx at 27.7 m distance (DWH full output, VN optic) Colour Consistency 2 SDCM Lumen Maintenance L70 120,000 hrs (Ta 25 °C) 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 1 / 13 Specification sheet Large Pendant DYNAMIC WHITE Physical Housing Material Low copper content high pressure die-cast aluminium Lens Material Clear tempered glass Hardware Material Stainless steel Gaskets Silicone Surface Finish Electrostatically applied polyester powder coat Weight 5.44 kg EPA Front = 0.09 sq m, Side = 0.05 sq m Electrical and control Voltage 100 to 277 volts Fixture Cable Power and data cable goes through stem Inrush Current (peak) 55A @230VAC Resolution (DMX/RDM) Per fixture, 8-bit or 16-bit Dynamic Warm Colour Temperature Mixing 36 LEDs (12x 2200K, 12x 2700K, 12x 3000K) Dynamic White Colour Temperature Mixing 36 LEDs (12x 2700K, 12x 4000K, 12x 6500K) Control Lumentalk, Dim to Warm via 0-10V (DWW only), DMX/RDM enabled Dim to Warm via single channel (DWW only), DMX/RDM enabled 3-channel colour temperature control Environmental Operating Temperature -25 °C to 50 °C IP Rating IP66 fixture, IP54 canopy (suitable for wet location, not suitable for water jet) IK Rating IK10 Accessories (order separately) Control Boxes Power and control box - daisy chain configuration, Power and control box - star configuration Control Systems Lumentouch 2.0™, Lumencue, Pharos® TPC, Pharos® LPC X, Pharos® LPC Diagnostic and Addressing Tools LumenID, LumentalkID 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 2 / 13 Specification sheet Large Pendant DYNAMIC WHITE Mounting types SCAN - Standard straight stem canopy ACAN - Adjustable sloped ceiling canopy Optical options LSLH - Linear spread lens horizontal distribution LSLV - Linear spread lens vertical distribution Factory installed, not adjustable on site. Not available for WFL optic. See 'Optical Accessories' section for field adjustable spread lens (LSLA). 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 3 / 13 Specification sheet Large Pendant DYNAMIC WHITE Optical accessories (order separately) SN - Snoot SNW - Snoot Wide LBLSN-FINISH-BK Interior surface painted black. Please specify desired exterior FINISH from list of available finishes. LBLSNW-FINISH-BK Interior surface painted black. Please specify desired exterior FINISH from list of available finishes. VS - Visor LSLA - Linear Spread Lens Adjustable LBLVS-FINISH-BK Interior surface painted black. Please specify desired exterior FINISH from list of available finishes. LBLLSLA-FINISH Please specify desired exterior FINISH from list of available finishes. WG - Wire Guard Accessory combinations LBLWG-FINISH Please specify desired exterior FINISH from list of available finishes. Accessory combinations must be ordered together on a single line Ex: A Snoot + Wire Guard combination order code is LBLSNWG-BK-BK. 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 4 / 13 Specification sheet Large Pendant DYNAMIC WHITE Available exterior finishes for optical accessories BK - Black Sandtex® BRZ - Bronze Sandtex® SI - Silver Sandtex® WH - Smooth white BKTX - Textured black BRZTX - Textured bronze, non-metallic GRATX - Textured medium grey GRNTX - Textured green WHTX - Textured white CC - Custom colour and finish (please specify RAL colour)* *Lumenpulse offers a wide selection of RAL CLASSIC (K7) colours with a smooth texture and high-gloss finish. Please consult factory for a list of available K7 colours, other RAL textures and glosses, or to match alternate colour charts. Final colour matching results may vary. 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 5 / 13 Specification sheet Large Pendant DYNAMIC WHITE Typical wiring diagrams Wiring colour code Lumentalk (LT) A - Third party DMX/RDM controller B - Lumentranslator (LTL-DMX) C - Data wiring (by others) D - Power line (120-277V AC) E - Junction box (by others) F - Power wiring (by others) G - Lumenbeam Large Pendant Lumentalk (LT) - wiring detail A - Power input (control over power line via Lumentalk system) or from previous fixture B - To fixture C - To next fixture D - Live E - Ground F - Neutral G - Terminal connector (by others) H - Junction box (by others) Consult factory for specific applications and maximum fixture count/cable length recommendations. Lumentalk enabled fixtures must be commissioned using LumentalkID software and a LID-LT. Consult factory for details. Maximum of 1 transmitter (Lumentranslator or Lumenlink) per system. No third party fixtures allowed on the same circuit. 1 DMX controller per Lumentalk network, maximum of 48 DMX channels per Lumentalk network (minimum step transition update rate is 1 second, minimum fade time between two colours is 1 minute). Consult factory for applications that require additional capabilities. 50 watts per fixture. 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 6 / 13 Specification sheet Large Pendant DYNAMIC WHITE Dim to Warm via 0-10V (DIM/DTW*) *Available for DWW version only, 2700K to 2200K A - Third party dimmer B - Data wiring (by others) C - Power input (100-277V) D - Power and data wiring (by others) E - Junction box (by others) F - Lumenbeam Large Pendant Dim to Warm via 0-10V (DIM/DTW) - wiring detail - CE A - Power input or from previous fixture B - To fixture C - 0-10 V + D - 0-10 V E - To next fixture F - Live G - Ground H - Neutral I - Terminal connector (by others) J - From third party dimmer K - Junction box (by others) Dim to Warm via 0-10V (DIM/DTW) - wiring detail - CE Class II option A - Power input or from previous fixture B - To fixture C - 0-10 V + D - 0-10 V E - To next fixture F - Live G - Signal common H - Neutral I - Terminal connector (by others) J - From third party dimmer K - Junction box (by others) Consult factory for specific applications and maximum fixture count/cable length recommendations. 0-10V mA ratings: passive dimmer (Current Sink): 3mA per fixture, active dimmer (Current Source): 0.5mA per fixture. 50 watts per fixture. 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 7 / 13 Specification sheet Large Pendant DYNAMIC WHITE Star Layout (Dim to Warm via DMX/RDM1* or 3-channel DMX/RDM) *Available for DWW version only, 2700K to 2200K A - Third party DMX/RDM controller B - Data input (Belden 9841 or equivalent, by others) C - Data output to next CBX (optional, not isolated/not boosted) D - CBX-ST E - Power input (100-277V) F - Power and data output to fixture (wiring by others) G - Junction box (by others) H - Lumenbeam Large Pendant Star Layout (DMX/RDM1 or DMX/RDM) - wiring detail - CE A - From CBX or previous fixture B - Lumenterminator* C - To fixture D - Data E - Data + F - Neutral G - Ground H - Live I - Terminal connector (by others) J - Junction box (by others) Star Layout (DMX/RDM1 or DMX/RDM) - wiring detail - CE Class II option A - From CBX or previous fixture B - Lumenterminator* C - To fixture D - Data E - Data + F - Neutral G - Signal common H - Live I - Terminal connector (by others) J - Junction box (by others) Consult factory for specific applications and maximum fixture count/cable length recommendations. Run length calculations are based on a voltage drop of no more than 25V. The DMX/RDM protocol states a maximum of 32 DMX/RDM enabled fixtures on any single run. Maximum of 4 DMX/RDM repeaters/CBX cascading in line. Maximum of 6 outputs per CBX-ST. DMX/RDM1 control option requires 1 DMX address. DMX/RDM control option requires 3 DMX addresses. 50 watts per fixture. * DMX terminator is required at the end of each run to maintain data integrity. (6x) DMX lumenterminators included per CBX-ST. See installation instructions for details. 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 8 / 13 Specification sheet Large Pendant DYNAMIC WHITE Daisy Chain Layout (Dim to Warm via DMX/RDM1* or 3-channel DMX/RDM) *Available for DWW version only, 2700K to 2200K A - Third party DMX/RDM controller B - Data input (Belden 9841 or equivalent, by others) C - Data output to next CBX (optional, not isolated/not boosted) D - CBX-DS E - Power input (100-277V) F - Power and data output to fixture (wiring by others) G - Junction box (by others) H - Power and data wiring (by others) I - Lumenbeam Large Pendant Daisy Chain Layout (DMX/RDM1 or DMX/RDM) - wiring detail (first or middle of run) - CE A - From CBX or previous fixture B - To fixture C - Data + D - Data E - To next/from previous fixture F - Live G - Ground H - Neutral I - Terminal connector (by others) J - Junction box (by others) Daisy Chain Layout (DMX/RDM1 or DMX/RDM) - wiring detail (end of run) - CE A - From CBX or previous fixture B - Lumenterminator* C - To fixture D - Data E - Data + F - Neutral G - Ground H - Live I - Terminal connector (by others) J - Junction box (by others) Daisy Chain Layout (DMX/RDM1 or DMX/RDM) - wiring detail (first or middle of run) - CE Class II option A - From CBX or previous fixture B - To fixture C - Data + D - Data E - To next/from previous fixture F - Live G - Signal common H - Neutral I - Terminal connector (by others) J - Junction box (by others) 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 9 / 13 Specification sheet Large Pendant DYNAMIC WHITE Daisy Chain Layout (DMX/RDM1 or DMX/RDM) - wiring detail (end of run) - CE Class II option A - From CBX or previous fixture B - Lumenterminator* C - To fixture D - Data E - Data + F - Neutral G - Signal common H - Live I - Terminal connector (by others) J - Junction box (by others) Consult factory for specific applications and maximum fixture count/cable length recommendations. Run length calculations are based on a voltage drop of no more than 25V. The DMX/RDM protocol states a maximum of 32 DMX/RDM enabled fixtures on any single run. Maximum of 4 DMX/RDM repeaters/CBX cascading in line. Maximum of 1 output per CBX-DS. Maximum 0.9 m cable length recommended between fixture and next junction box for daisy chain layout. DMX/RDM1 control option requires 1 DMX address. DMX/RDM control option requires 3 DMX addresses. 50 watts per fixture. * DMX terminator is required at the end of each run to maintain data integrity. (2x) DMX lumenterminators included per CBX-DS. See installation instructions for details. 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 10 / 13 Specification sheet Large Pendant DYNAMIC WHITE Accessories (order separately) Control Boxes CBX-DS-Power and control box - daisy chain configuration CBX-ST-Power and control box - star configuration DMX/RDM control box. One power and data output to fixture or fixture run. Ethernet enabled option. Refer to CBX specification sheet for details. DMX/RDM control box. Up to six power and data outputs to fixtures or fixture runs. Ethernet enabled option. Refer to CBX specification sheet for details. Control Systems LTO2-Lumentouch 2.0™ LCU-Lumencue Lumentouch is a wall mount DMX 512 controller keypad. Lumencue is a USB / mini SD DMX 512 controller. TPC-Pharos® TPC LPC X-Pharos® LPC X The Pharos Touch Panel Controller (TPC) is a wall-mounted DMX512 controller with a capacitive touch screen. The Pharos Lighting Playback Controller X (LPC X) is designed for large-scale lighting installations and extremely complex lighting projects. LPC-Pharos® LPC The Pharos Lighting Playback Controller (LPC) is designed for small and mid-size lighting installations. Diagnostic and Addressing Tools LID-LumenID LID-LT-LumentalkID LumenID is a diagnostic and addressing DMX/RDM tool. It must be specified on all DMX applications. Refer to LID specification sheet for details. LumentalkID is a diagnostic and addressing tool. It must be specified for all Lumentalk (LT) applications. Refer to LID-LT specification sheet for details. 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 11 / 13 Specification sheet Large Pendant DYNAMIC WHITE How to order LBLP 1 . Housing LBLP 2 . Voltage Lumenbeam™ Large Pendant 3 . Colour and Colour Temperature 100 100 volts 120 120 volts 208 208 volts 220 220 volts 240 240 volts 277 277 volts 4 . Optics DWW Dynamic warm white (2200K to 3000K) VN Very Narrow 6° DWH Dynamic white (2700K to 6500K) NS Narrow Spot 10° NF Narrow Flood 20° FL Flood 40° WFL Wide Flood 60° 5 . Mounting Type 6 . Mounting Length (1) SCAN Straight stem canopy 12 305 mm ACAN Adjustable sloped ceiling canopy 24 610 mm 36 914 mm 48 1219 mm 7 . Optical Option 8 . Finish LSLH Linear spread lens horizontal distribution (2) BK Black Sandtex® LSLV Linear spread lens vertical distribution (2) (3) BRZ Bronze Sandtex® SI Silver Sandtex® WH Smooth white BKTX Textured black BRZTX Textured bronze non-metallic GRATX Textured medium grey GRNTX Textured green WHTX Textured white CC Custom colour and finish (please specify RAL colour) (4) 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 12 / 13 Specification sheet Large Pendant DYNAMIC WHITE 9 . Control 10 . Options LT Lumentalk (5) (6) DIM/DTW Dim to Warm via 0-10V (2700K to 2200K) (7) DMX/RDM1 Dim to Warm via single-channel DMX/RDM (2700K to 2200K) (7) DMX/RDM 3-channel colour temperature control via DMX/RDM CRC Corrosion-resistant coating for hostile environments (8) 11 . Certification UL UL compliant CE CE compliant CEII CE compliant Class II double insulated Notes: (1) ​Consult factory for custom stem lengths. (2) Not available for WFL optic. Factory installed. Field adjustable spread lens accessory available, order separately. (3) Factory installed, available for 6° to 40° optics. See Optical Accessories for field adjustable spread lens. (4) Lumenpulse offers a wide selection of RAL CLASSIC (K7) colours with a smooth texture and high-gloss finish. Please consult factory for a list of available K7 colours, other RAL textures and glosses, or to match alternate colour charts. Final colour matching results may vary. (5) A Lumentranslator and LumentalkID must be specified for Lumentalk applications. Consult Lumentranslator and Lumentalk pages and specification sheets for details. (6) Not available with Class II double insulated option. (7) Available for DWW colour temperature option only. (8) Use only when exposed to salt spray and harsh chemicals. This option is not required for normal outdoor exposure. 11/13 Weston Street, Unit no 13.3.2 London, SE1 3ER GB T +44 (0) 2031 765370 [email protected] www.lumenpulsegroup.com Lumenpulse reserves the right to make changes to this product at any time without prior notice and such modification shall be effective immediately 2017.08.30 copyright © 2017 lumenpulse MG - R14 13 / 13