Transcript
SPECIFICATIONS WF182BD03/04 7” die cast, paper cone mid/woofers, 4/8 ohm The 7” transducers WF182BD03 (4 ohm) and WF182BD04 (8 ohm) were designed as high performance bass and midrange units for monitors and high-end hi-fi speakers. They offer outstanding deep bass performance and dynamic and detailed midrange.
FEATURES
• Balanced Drive motor structure for optimal drive force symmetry resulting in largely reduced even order harmonic distortion • Copper cap on center pole to reduce voice coil inductance and to minimize variations in voice coil inductance as a function of voice coil position • Black coated semi-air-dried paper cone • Rigid die cast alu chassis with extensive venting for lower air flow speed reducing audible distortion • Vented voice coil former for reduced distortion and compression • Vented center pole with dual flares for reduced noise level at large cone excursions • Heavy-duty black fiber glass voice coil former to reduce mechanical losses resulting in better dynamic performance and low-level details • Large motor with 1½” voice coil diameter for better control and power handling • Built-in alu field-stabilizing ring for reduced distortion at high levels • Low-loss suspension (high Qm) for better reproduction of details and dynamics • Black motor parts for better heat transfer to the surrounding air • Conex spider for better durability under extreme conditions • Gold plated terminals to ensure long-term trouble free connection
NOMINAL SPECIFICATIONS Notes
1 2 2 2 3, 6 3 3, 6 3, 6 3, 6 3, 6 3, 6 3, 6 4 5
3, 5 3, 5 3, 5 3, 5 Note 1 Note 2 Note 3 Note 4 Note 5
Note 6
WF182BD03
Parameter
Before burn-in
Nominal size Nominal impedance Recommended max. upper frequency limit Sensitivity, 2.83V/1m (average SPL in range 200 - 1,000 Hz) Power handling, short term, IEC 268-5, no additional filtering Power handling, long term, IEC 268-5, no additional filtering Power handling, continuous, IEC 268-5, no additional filtering Effective radiating area, Sd Resonance frequency (free air, no baffle), Fs Moving mass, incl. air (free air, no baffle), Mms Force factor, Bxl Suspension compliance, Cms Equivalent air volume, Vas Mechanical resistance, Rms Mechanical Q, Qms Electrical Q, Qes Total Q, Qts Voice coil resistance, RDC Voice coil inductance, Le (measured at 10 kHz) Voice coil inside diameter Voice coil winding height Air gap height Magnet weight Total unit net weight excl. packaging Krm Erm Kxm Exm
After burn-in
WF182BD04 Before burn-in
After burn-in
7 4 2.5 91
7 8 2.5 88
80 131
80 131
39
33.8
40
16.7 6.75 1.0 24.4 0.37 11 0.30 0.29
1.33 32.4 0.43 8.2 0.26 0.25 3.3 0.088 39 16 5 885 2.3 33 0.42 157 0.19
33.4 16.1 8.5
1.0 24.4 0.37 10.9 0.35 0.34
1.33 32.4 0.43 8.1 0.30 0.29 6.3 0.14 39 16 5 885 2.3 54 0.40 347 0.14
Unit [inch.] [ohm] [kHz] [dB] [W] [W] [W] [cm²] [Hz] [g] [N/A] [mm/N] [lit.] [Ns/m] [-] [-] [-] [ohm] [mH] [mm] [mm] [mm] [g] [kg] [mohm] [-] [mH] [-]
Measured in infinite baffle. Tested in free air (no cabinet). Measured using a semi-constant current source, nominal level 2 mA. Measured at 20 deg. C It is generally a rough simplification to assume that loudspeaker transducer voice coils exhibit the characteristics of an inductor. Instead it is a far more accurate approach to use the more advanced model often referred to as the “Wright empirical model”, also used in LEAP-4 as the TSL model (www.linearx.com), involving parameters Krm, Erm, Kxm, and Exm. This more accurate transducer model is described in a technical paper here at our web site. After burn-in specifications are measured 12 hours after exiting the transducer by a 20 Hz sine wave for 2 hours at level 10/14.1 VRMS (4/8 ohm version). The unit is not burned in before shipping.
Specifications are subject to change without any further notice. Copyright © 2010 by Wavecor Ltd., Guangzhou, China. All rights reserved. Wavecor® is a registered trademark of Wavecor Ltd. For more information please visit www.Wavecor.com
Page 1
SPECIFICATIONS WF182BD03/04 7” die cast, paper cone mid/woofers, 4/8 ohm dBSPL 110
Ohm
SPL & impedance response, WF182BD03
300
on axis 15 deg. off axis 30 deg. off axis 45 deg. off axis 60 deg. off axis Impedance
105 100
200
100
95 50 90 85
20
80 10
75 70
5
65 60
20
50
100
200
500
1k
2k
5k
10k
20k
2
Frequency, Hz Measuring conditions, SPL Driver mounting: Flush in infinite baffle, back side open (no cabinet) Microphone distance: 1.0 m Input level: 2.83 VRMS Smoothing: 1/6 oct.
dBSPL 110
Measuring conditions, impedance Driver mounting: Free air, no baffle, back side open (no cabinet) Input signal: Semi-current-drive, nominal current 2 mA Smoothing: None
Ohm
SPL & impedance response, WF182BD04
300
on axis 15 deg. off axis 30 deg. off axis 45 deg. off axis 60 deg. off axis Impedance
105 100
200
100
95 50 90 85
20
80 10
75 70
5
65 60
20
50
100
200
500
1k
2k
5k
10k
20k
Frequency, Hz Specifications are subject to change without any further notice. Copyright © 2010 by Wavecor Ltd., Guangzhou, China. All rights reserved. Wavecor® is a registered trademark of Wavecor Ltd. For more information please visit www.Wavecor.com
Page 2
2
SPECIFICATIONS WF182BD03/04 7” die cast, paper cone mid/woofers, 4/8 ohm OUTLINE DRAWING (nominal dimensions, mm)
max. 84
7.5
3
6
5
max.
120 153
Foam gasket
169.5 182
CONNECTIONS
7.1
6.5
Red mark for positive terminal
2.8
4.8
Thickness, both terminals: 0.5 mm Terminal plating: Gold
PACKAGING AND ORDERING INFORMATION Part no. WF182BD03-01
4 ohm version, individual packaging (one piece per box)
Part no. WF182BD03-02
4 ohm version, bulk packaging
Part no. WF182BD04-01
8 ohm version, individual packaging (one piece per box)
Part no. WF182BD04-02
8 ohm version, bulk packaging
Latest update: September 8, 2010 Specifications are subject to change without any further notice. Copyright © 2010 by Wavecor Ltd., Guangzhou, China. All rights reserved. Wavecor® is a registered trademark of Wavecor Ltd. For more information please visit www.Wavecor.com
Page 3
