Transcript
Windows 2000
Speedway ISDN TA USB Software Installation Guide IMPORTANT Please read this guide before attempting to install your TA
Introduction Follow the instructions contained within the Speedway ISDN TA installation guide up to the section, Installing the Speedway ISDN TA software. Then proceed with the installation by following the instructions contained in this supplement. Installing the Speedway ISDN TA software Installing the Speedway ISDN TA software using the Windows 2000 USB connection Ensure no windows applications are running. Connect the USB cable to the PC that has been previously attached to your TA. Windows 2000 will detect the TA (If this does not happen refer to the ‘Trouble shooting’ section at the end of this supplement.) A Found New Hardware window will show that a USB ISDN-Connector has been detected, please wait whilst the PC prepares for the next stage of installation. The Found New Hardware Wizard appears and displays that it is going to help install the drivers for your hardware. Click Next. Insert the Speedway CD ROM. (If the Welcome to BT Speedway TA screen is displayed, please close this screen.) In the next Window (shown below) the wizard details the device to be installed USB ISDN-Connector, under the question What do you want the wizard to do? select the option Search for a suitable driver for my device.
1
Click Next In the next Window (shown below) tick only the Specify a location option.
Click Next At the next window (shown below) either enter (your CD drive):\windows.2k into the Copy Manufacturer’s files from: input box, or use the Browse button to bring up a browse window (shown below) and open the Windows.2k folder found on the Speedway CD ROM.
2
Click Open Click OK Windows now searches for drivers for the new hardware, this may take a few minutes. Wait until it displays the correct location of the drivers, (your CD drive):\windows.2k\speedta.inf. Click Next The next window (shown below) appears, this is a Digital Signature not found window.
Click Yes Windows then copies the files to the system The next window confirms the system has finished installing the drivers. Click Finish Eject and re-insert the Speedway CD ROM. The CD should automatically load and you should see the Welcome screen (shown below). If the CD does not automatically load use Windows Explorer (or Start menu/Run…) to open the intro.hlp file on the Speedway CD ROM.
3
Click on the BT icon. The next screen (shown below) shows the operating systems under which the Speedway ISDN TA can be installed.
Click on the Microsoft Windows 2000 button.
4
The next screen (shown below) provides instructions on how to install the device.
Click on the Install button. The installation for Speedway! Applications program will now start and the BT Speedway Welcome screen is displayed. It is best to follow the on-screen instructions that are now displayed, but you may find it easier to refer to the section: Installing the Speedway! Applications contained in the Speedway ISDN TA installation guide.
5
Troubleshooting & Support Hints & Tips It is a good idea to view the Readme file on the CD for the latest product information and installation advice.
Problem: Found New Hardware Wizard does not start when installing USB device. If the hardware wizard fails to start check the following: Make sure the ‘Universal Serial Bus controller’ is installed in your Windows system. This can be checked by opening the Control Panel (Start – Settings Control Panel). Double-Click on the System icon, click on Hardware tab, click on Device Manager button and scroll down list. The ‘Universal Serial Bus controller’ should be shown in the device list. If this is not available refer to your Windows manual in order to install new components.
6
Offices worldwide Windows is a registered trademark of Microsoft Corporation. Adobe and Acrobat are trademarks of Adobe Systems, Inc Speedway and Speedway! are trademarks of British Telecommunications plc. TouchtoneTM is a registered trade mark of British Telecommunications plc in the UK. © British Telecommunications plc 2000. Registered Office: 81 Newgate Street, London EC1A 7AJ. Registered in England No. 1800000. Speedway USB (Windows 2000) (7/00) 6 Designed by The Art & Design Partnership Limited. Printed in Germany. Printed on paper which meets international environmental standards.
CE compliant to 89/336/EEC (EMC Directive) & 73/23/EEC (Low Voltage Directive)
