Transcript
Specifications
Packing list User Manual
Product Name: Smart touch lamp speaker Model No.: SPK-V01 Power Input: Micro USB,DC5V 1000mA Battery Capacity: 3.7V/2000mA Charging Time: 2.5-4hours Speaker Specification: 2.5Inch,4ohm/5W Frequency Response: 70Hz-20KHz
Smart Touch Lamp Speaker
Song Length
Distortion: ≤0.5% TF Card Mode
Signal to Noise Ratio: ≥65db Material: ABS/Silica-gel Music Playing Time: 15 hours at volume level 15. Lighting Time: 15 hours at the lowest brightness. Speaker
12 13
14
15
16
17
Note: LED display will be off after 5min if no touch to the product.
User Manual
Button/Indicator List Button Functions
3.5mm Audio Cable BT SD
USB Cable
FM
SPK-V01
Introduction Smart touch lamp speaker is a product which integrates a touch sensitive lamp and Bluetooth speaker. The touchable lamp can be easily switched on/off and adjusted to different brightness levels by a hand touch at the top-center of the product. The Bluetooth speaker is a smart device which combines audio player (Bluetooth mode, SD mode, Line In mode), FM player, and clock functions. Please check the detailed operations of each function in the Specifications. For operation, please refer to the Operating Instructions.
1 2 6
3
5 4
7
8
9
11 10
1 Power Switch: Used to cut off power supply for safety purposes in delivery. The product will not get power when this switch is off. 2 Alarm Set: Enter alarm set mode. 3 Sleep Indicator: It will light when sleep mode is turned on. 4 Sleep: Turn on/off automatic sleep mode. 5 Alarm On: Turn on/off the alarm. 6 Clock Set: Enter clock set mode. 7 Charging Port: Micro USB port for power input. 8 Charging Indicator: To show if battery's charging 9 TF Port: Port to insert TF card. 10 Line In: 3.5mm port to connect line in signal. 11 Micro Phone: Micro phone for hand free call in bluetooth mode. 12 LED Display 13 Mode: Switch speaker to different modes (bluetooth, TF, line in, FM tuner). 14 : Play back/volume down/number down. 15 : Play forward/volume up/number up. 16 : Play/pause/answer phone 17 ON/OFF: Switch to active/sleep mode.
Operational Instructions
Clock Setting
Bluetooth Hand Free Call
To enter Clock Setting mode, hold the 6 Clock Set button until the hour number begins flashing. Press 16 to switch hours or minutes. Press 15 to set displayed numbers. press 6 Clock Set to 14 set and quit clock setting.
In bluetooth mode, the speaker will read the calling number when a call is coming in. Press 16 to pick up a hand free call. Please speak closer to the micro phone to get better voice quality.
Alarm Setting
Insert a TF card with music, and press Mode to enter the ”TF Card Music Mode”. The speaker will automatically play music in order of the stored date.
To enter Alarm Setting Mode, hold the 2 Alarm Set button until the hour number begins flashing. Press 16 to switch hours or minutes. Press 15 to set displayed numbers. Press 2 Alarm Set to 14 set and quit alarm setting. 5 Alarm On button is to simply turn on and off the alarm.
Power On and Charging Caution: Turn on 1 power switch before first use by pressing with a pin. This is the switch for the power supply, and it is normally tumed off for safety measures during delivery. The product will not work if the switch is off. Charge the speaker with the provided USB cable which is compatible with any cell phone charger.( Note: the output voltage is 5V, and output current should be 1000mA and above). The 8 charging indicator is red while charging and goes off when the speaker is fully charged.
ON/OFF Slide 17 ON/OFF to switch the speaker into Active or Sleep mode. In Active mode, all functions are available. In Sleep mode, only the alarm/clock is running and power consumption is at its lowest for extended battery life.
Speaker Mode Selection Press 13 Mode to switch the speaker to different modes: Bluetooth mode, TF card music mode, line in mode, FM tuner mode, standby mode. If there is no TF card inserted in the TF port, the mode cycle will skip TF card music mode.
Bluetooth Mode Press 13 Mode to enter Bluetooth mode. The speaker will be ready for pairing, and the screen will display “blue”. Open the Bluetooth setting on your Bluetooth device and search for the speaker. Select “Lamp Speaker” to connect, and the speaker will say “ Bluetooth is connected” when connection succeeds.
TF Card Music Mode
Volume Up: Hold 15 Volume Down: Hold 14 Previous Song: Press 14 Next Song : Press 15 Play/Pause: Press 16
Touch Lamp
Line In Mode Press Mode button to enter the “Line In Mode”. Connect the speaker to an audio source with the 3.5mm connector. Volume Up: Hold 15 Volume Down: Hold 14
Volume Up: Hold 15 Volume Down: Hold 14 Previous Song: Press 14 Next Song : Press 15 Play/Pause: Press 16
USB data cable as the FM antenna
Note: Don't slide ON/OFF too quickly, wait at least 2s after each slide.
Automatic Sleep Mode Press the 4 sleep button to choose 10min,20min, or 30min countdown. When time is set, countdown will start after 3 seconds and turn on 3 blue indicator .
Note: (1) When the same bluetooth device is used again, the speaker will connect automatically. A new Bluetooth connection cannot be made if the last connection is not cut off. (2) If the Bluetooth device cannot be paired successfully, please remove the “Lamp speaker” name in your device and reboot the speaker by turning off and back on using the 1 Power switch.
FM Tuner Mode Press 13 Mode button to enter the FM Tuner Mode, and connect USB cable to power port as FM radio antenna. Press 16 , the speaker will automatically search and store available FM radio channels. Press 14 and 15 to switch and play the saved channels. The speaker can save up to 99 channels.
Touch the center of the top speaker grill, the lamp will switch to 3 different lighting levels after each touch.
Low Battery Alarm If the battery power is too low, the speaker will beep twice and automatically go into sleep mode. Please slide the ON/OFF switch to OFF and charge the product. When charged, the product can be switched back on.
