Transcript
SPM6020HR-233-16 Accelerator PCI-104 dspModule™ TMS320C6202 based Industrial DSP Module Bus master or target only PCI Interface Operating Temperature: -40º to +85º C PCI Expansion Bus
Features:
3.3V & 5V PCI signaling compatible 233 MHz TMS320C6202 DSP 1864 MIPS operation PCI Controller - PLX PCI9054 Eight 32-Bit Instructions/Cycle 4.3ns cycle time 16 Mbytes SDRAM 466 MB/s transfer rate 2 Mbytes FLASH All DSP resources accessible from the PCI bus VLIW instruction device Watch-Dog Timer Bus master or target only (Jumper Enabled) Complete High performance DSP accelerator module Stackable 120-pin PCI expansion bus for use with PCI-104 and PC/104-Plus modules Stackable 80-pin PlatformBus (Buffered ASynchronous Memory Interface of the DSP) 3 Multi channel Buffered Serial Port (McBSP) (max. 100Mbit/s ) Boot Mode: Map1, Internal, HPI, or Map1, Internal, 16 Bit ROM Boot Mode (Jumper Enable) All resources of the DSP can be accessed from the PCI bus TMS320™ DSP ALGORITHM STANDARD Mating Connectors Standard 14-pin 0.1" DIL header (JTAG) Standard 10-pin 0.1" DIL header (SyncBus) 3 Standard 10-pin 0.1" DIL headers (McBSP)
SyncBus Texas Instruments TMS320C6202
McBSP
McBSP
JTAG McBSP
PCI
DSP PlatformBus
rotary switch
SPM6020HR-233-16 dspModule™
with standard Heatsink installed
Rugged IDAN® Configuration
I/O:
Processor PlatformBus (3.3V) 32 bit data 16 bit address Buffered ASynchronous Memory Interface of the DSP High speed data transfer device between the DSP and the analog interface Three Multi channel Buffered Serial Ports (McBSP): Buffered ASynchronous Memory Interface of the DSP High speed data transfer device between the DSP and the analog interface TI/EI, MVIP, SCSA, ST bus, AC97 SPI Compatible JTAG emulator connector Boundary-Scan-Compatible SyncBus for Synchronous operation Up to 4 AIM6020HR Analog Interface Modules and/or PC/104-Plus Data Acquisition boards PCI-104 Data Acquisition board
Software:
DOS (DPMI32) driver with example programs. Windows 98/NT4/2000/XP driver with example programs. Linux driver with example programs.
systerra computer GmbH | Kreuzberger Ring 22 · D-65205 Wiesbaden | Tel: 0611 9748 470
DOS and Windows drivers feature the RTD dspFramework, a suite of libraries and example programs to simplify application development. Key features of the RTD dspFramework include: Matching host-side and DSP-side libraries. Standard interfaces for passing messages between the DSP and the host system. Ability for the host to call DSP functions. Support for single and multi-threaded applications (DSP/BIOS). Support for on-board hardware (McBSP, SyncBus, Flash, etc). DSP applications can be downloaded through the PCI bus, or programmed into the on-board flash. Modular design and full source code makes it possible to modify and extend the framework. Source code, example programs, and API documentation are included for all supported platforms. TI Code Composer Studio required to develop and compile DSP applications.
TI DSP TOOLS AND SOFTWARE
Physical Attributes:
Size: 90mm L x 96mm W x 15mm H (3.6"L x 3.8"W x 0.6"H) Weight: Approximately 0.10 Kg (0.22 lbs.) Standard Operating Temperature: -40° to +85°C: 90% humidity non-condensing Storage Temperature: -55° to +125°C Power requirements 233 MHz: 3W @ 5 VDC typical
systerra computer GmbH | Kreuzberger Ring 22 · D-65205 Wiesbaden | Tel: 0611 9748 470
