Transcript
Spreading Wings S900 User Manual 2016.01
V1.4
Disclaimer Thank you for purchasing the S900. Please visit the Spreading Wings S900 page on www.dji.com regularly to keep up to date with product information, technical updates and manual corrections. Information in this manual is subject to change without notice. In using this product, you hereby agree to this disclaimer and signify that you have understood all points completely. When assembling this product, follow all instructions carefully. The manufacturer and seller assume no liability for any damage or injury arising from the use of this product. This is a class A product of the FCC certification. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. DJI is a registered trademark of DJI. Names of product, brand, etc., appearing in this manual are trademarks or registered trademarks of their respective owner companies. This product and manual are copyrighted by DJI with all rights reserved. No part of this product or manual shall be reproduced in any form without the prior written consent or authorization of DJI.
About The S900 is designed for professional aerial photography and cinematography. It is user friendly, safe, stabilized and easy to fly while its integrated design makes assembly and configuration simple and fast. Retractable landing gear, vibration dampers, slightly angled arms and a minimalized gimbal mount allow for a clear 360 degree view from the camera. A patented power distribution board, built-in high-speed ESCs and motors with high efficiency propellers ensure dynamic stability and maximized power efficiency. Used with a professional DJI multi-rotor autopilot system, the S900 can hover and fly reliably making it ideal for photography and cinematography.
126mm 305mm
433mm
2
© 2016 DJI. All Rights Reserved.
Contents Disclaimer
2
About
2
Contents
3
Cautions
4
Legend
4
In The Box
5
Mounting the Landing Gear
6
Mounting Frame Arms
7
Mounting Electronics and Wiring
11
Connecting XT60 Ports on the Center Frame
16
Installing Battery
16
Setting Up the Landing Gear
18
Mounting the Gimbal
20
Appendix
22
ESC Sound
22
ESC LED
22
Specifications
22
Gain Value Settings
23
FAQ
24
Soldering the ESC
24
Remounting the Propellers
24
Propeller Precautions
24
Using the Propeller Holder
25
Assembling Motor Vibration Absorbers
25
Remounting the Landing Gear Servo
26
Recalibrating Servo Travel
26
Part List
27
FCC Statements
31
© 2016 DJI. All Rights Reserved.
3
Cautions When flying, the rotating propellers may cause serious damage and injury. Please fly safe at all times.
Assembly Cautions Cautions
1. Use a bracket to mount the GPS module on the center frame to avoid interference with the power board. 2. Ensure the IMU is mounted with the arrow pointing toward the nose of the aircraft. 3. If using a receiver, attach it under the bottom board of the center frame with the end of the antenna facing downwards and away from obstructions to avoid signal loss. 4. Ensure frame arms are mounted correctly. a) Motor mounts with CCW marks should be mounted to the center frame positions with the following marks: M1, M3 and M5. b) Motor mounts with CW marks should be mounted to the center frame positions with the following marks: M2, M4, and M6. 5. Do not remove any glued-in screws. 6. Screws that already have blue glue can be used once without thread locker. On other occasions, apply appropriate thread locker first. 7. The S900 should be lifted off the ground when testing landing gear or recalibrating servo travel.
Flight Cautions 1. ESCs are not water-proof, please do not fly in rain or snow. 2. Ensure all soft dampers and vibration absorbers are in good condition before every flight. If not, replace immediately. Otherwise, the flight performance of your aircraft will be adversely affected. 3. Ensure all parts are in good condition before each flight. Do not fly with worn or broken parts. 4. Ensure propellers and motors are installed correctly and propellers are unfolded before flying. 5. Ensure ESC signal connectors and power cable connectors are tight before every flight. 6. When flying, maintain a safe distance away from people, buildings, high-voltage lines, tall trees, water and other hazards. 7. Use only 6S LiPo batteries for the power supply. 8. Ensure all output signals from M1 to M6 are in proper working order when using the DJI A2 flight control system to avoid damage or injury. 9. Do not overload the system. 10. Do not get close to or touch motors or propellers when they are spinning as this can cause serious injury. 11. Disconnect the battery and remove the camera during transportation to avoid damage or injury. 12. We strongly recommend using as many DJI manufactured parts as possible.
Others If you have any problems you cannot resolve, contact your dealer or DJI customer service.
Legend Important
4
© 2016 DJI. All Rights Reserved.
Hints and Tips
In The Box Frame Arms ×6
Landing Skid Tubes ×2 (with Silicone Rubber Dampers)
Landing Gear Legs ×2
GPS Collapsible Mount ×1
Springs ×2
Connection Cable
Accessories Package ×1
Connector Set ×1
CW propellers ×2 CCW propellers ×2 Magic tapes ×4 The red knobs ×6 Landing gear leg rings ×4 Soft dampers ×50
In The Box
Center Frame ×1
or
3-PIN Connection Cables ×8
3-PIN Servo Cable ×1
Screw Package ×1 For frame arms mount: M4×35 For landing gear mount: M3×8, M2.5×8 (socket cap), M3×22 (socket cap)
Tools Required Tools
Usage
2.0mm Hex Wrench, 2.5mm Hex Wrench
Mounting screws.
Thread Locker
Fastening screws.
Nylon Cable Tie, Scissors, Cutting Pliers/Dykes
Binding devices and wires.
Foam Double Sided Adhesive Tape
Mounting receiver, controller and other modules.
© 2016 DJI. All Rights Reserved.
5
Mounting the Landing Gear Instructions
1. Put one landing gear leg ring onto each landing gear leg. 2. Insert one landing gear leg into each landing skid tube and secure it in place by tightening the M2.5×8 (socket cap) screw. Ensure silicone rubber dampers are attached to each end. 3. Insert the landing gear leg into connection point on the center frame. Affix in place with M3×8 screws. 4. Connect both springs on the legs to the center frame.
Mounting the Landing Gear
M2.5×8 (socket cap)
Note the springs are 58.5mm before connecting to the center frame, and are stretched to 70mm when mounting is completed. It is recommended that the landing gear leg ring be placed about 30mm above the landing skid tube.
70mm
30mm
6
© 2016 DJI. All Rights Reserved.
Mounting Frame Arms Instructions
1. Prepare the arms. (1) Check all propellers for cracks, then install and screw each propeller cover on tightly. (2) Ensure all motors are mounted firmly and rotate freely. (3) Mount all arms with red propeller covers to M1 and M2 to indicate the nose of the S900. (4) Identify the CW and CCW marks on the arms. Mount the arms with the CCW mark to the M1, M3 and M5 positions of the center frame. The arms with the CW mark should be mounted to the M2, M4 and M6 positions of the center frame. Mounting Frame Arms
Cover
Propeller Screw Mount
Power Cable
ESC Signal Cable Screw Motor ESC
CW or CCW Mark LED* *LED is on after motor started.
2. Insert each frame arm vertically into the mounting area on the center frame. 3. Line up the screw holes of the frame arm and center frame. 4. Insert the M4×35 screw from the right of the frame arm (the thread is located on the left of the screw mount). Tighten each screw correctly. Over tightening may lead to connector abrasion.
© 2016 DJI. All Rights Reserved.
7
Spreading Wings S900 User Manual
5. Gently lift the frame arm. 6. Twist the red knob to lock each arm in place. Be sure there is an audible click, which indicates a proper lock. Check the arm for movement. To store, untwist the knob and lower the frame arm.
Mounting Frame Arms 7. Now unscrew 6 screws (M2.5×8 cheese) on the upper plate of the center frame and remove the upper plate. Then unscrew the 4 screws (M3×8 self-tapping, found under the center frame) of the round cover and remove it to gain access to the ESC and power cable installation area. 8. Plug each ESC signal cable into the slot near each arm on the center frame.
8
© 2016 DJI. All Rights Reserved.
Spreading Wings S900 User Manual
9. Connect the power cables to the center frame. Each cable must be screwed into a positive (+) or negative (-) gold bracket. Each bracket will have two cables of the same color screwed into it. Red cables are positive and black cables are negative. 10. To ensure a reliable connection, rotate the screw until it is both tight and parallel to the connecting bracket.
Mounting Frame Arms
11. Ensure all ESC cables, and power cables are correctly installed onto the center frame.
ESC cables power cables
© 2016 DJI. All Rights Reserved.
9
Spreading Wings S900 User Manual
12. Replace the round cover of the center plate, and re-tighten the 4 screws (M3×8 self-tapping). Then replace the upper plate of the center frame, and re-tighten the 6 screws (M2.5×8 cheese).
13. Double check all frame arms. Arms M1 and M2 are the forward facing (nose), arms M4 and M5 are the tail. Seen from the top, motors on arms M1, M3 and M5 rotate counter clockwise while those on arms M2, M4 and M6 rotate clockwise.
10
© 2016 DJI. All Rights Reserved.
Mounting Electronics and Wiring Eight positions are reserved for mounting a flight control system, wireless video transmission module, receiver, and other accessories. The DJI A2 flight control system has been used here as an example. If using an A2, follow mounting and wiring instructions found in the A2 flight control system user manual. If using the DJI WK-M flight control system, please refer to the WK-M user manual for connections. Also be sure the firmware on your DJI flight controller has been updated to the latest version.
Instructions
1. Attach IMU module to the IMU area of the center frame. Ensure that it points toward the nose. 2. Attach the PMU module to the center frame.
Mounting Electronics and Wiring
2S 6S
PM U V-S EN
PW
(2V @ 6V)
3V@ 5V X1
IMU Only mount the IMU in the IMU position of the center frame. 3. Mount the flight controller in the reserved position near the PMU module.
LED
F4 F3 F2 F1 X3 X2 X1
CONTROLLER UNIT
S2 S1
M1 M2 M3 M4 M5 M6 M7 M8
LINK
LED
F4 F3 F2 F1 X3 X2 X1
CONTROLLER UNIT
CAN1 CAN2
ANT
CAN1 CAN2
Reserved Position
LINK
ANT
M1 M2 M3 M4 M5 M6 M7 M8
S2 S1
A2 Flight Controller
© 2016 DJI. All Rights Reserved.
11
Spreading Wings S900 User Manual
4. Attach the GPS collapsible mount to the center frame using M2.5×8 screws. 5. Mount a GPS module to the GPS mount with a bracket. Ensure the arrow points toward the nose and avoid catching your fingers in the bracket when folding for transportation.
Mounting Electronics and Wiring
M1 M2
6. The other reserved positions are indicated in the diagram below and can be used for mounting a receiver, LED flight indicator, iOSD module and wireless video transmission module.
12
© 2016 DJI. All Rights Reserved.
Spreading Wings S900 User Manual
7. Check that every anti-drop screw has been firmly installed in the reserved positions. Thread locker is recommended. (1) Remove the anti-drop screws to apply appropriate thread locker. (2) Replace and tighten. 8. Note that the dampers are 30° silicon rubber. If you use other dampers or vibration absorbing balls, the quality of your aerial photography may be affected.
Mounting Electronics and Wiring
dampers
Mount the GPS with a bracket to avoid interference from the center frame power board. Use glue to install the GPS bracket. Ensure it is firm and stable before every flight. Always test motors using the Assistant Software after installation. Refer to your flight control system user manual for details.
© 2016 DJI. All Rights Reserved.
13
Spreading Wings S900 User Manual
Connecting the flight controller to the center frame
1. Connect the flight control system according to your flight control system user manual. 2. Connect the flight controller to the center frame with the connection cables. There are two kinds of connection cables. Choose the corresponding connection mode according to the connection cable in the box. Using the connector set:
M1 M2 M3 M4 M5 M6 M7 M8
LINK
LED
F4 F3 F2 F1 X3 X2 X1
CONTROLLER UNIT
ANT
CAN1 CAN2
S2 S1
M1 yellow M1
1
1
yellow
M2
3
M3
M2
M4
M3 M4 M5
3
2
M5 brown
2
M1 M2 M3 M4 M5 M6
brown
M6
M6
A2 Flight Controller
the ESC Signal Outlet
Using the 3-pin connection cable: M1 through M6 correspond to each motor number.
M2 M3
M1 M2 M3 M4 M5 M6
M5
the ESC Signal Outlet
14
© 2016 DJI. All Rights Reserved.
M3 M4 M5 M6
MM11 2 MM 2 M3 MM34 5 MM 4 M6 MM57 M8 M6 M7 M8
CAN1 CAN2
M6
M2
CAN1 CAN2
M4
M1
LINK
LED
LINK
F4 F3LED F2 F1 X3 X2 X1
CONTROLLER UNIT
CONTROLLER UNIT
S2
F4 F3 F2 F1 X3 X2 X1
S1
ANT
M1
ANT
Mounting Electronics and Wiring
Plug in the connector set to the ESC signal outlet on the center frame. Then plug in the connector set to flight controller as shown below. (1) Yellow 4-pin cables are for M1~ M4 connections. The yellow cable should be connected to M1. (2) Brown 4-pin cables are for M5~ M6 connections. The brown cable should be connected to M5. (3) Black 4-pin cables are for four continuous ground pins connections. M1~M4 are connected as the following diagram shows.
A2 Flight Controller
Spreading Wings S900 User Manual
If using a DJI WK-M flight controller, you must use the wires that came with the WK-M. M1 through M6 correspond to each motor number.
M1 M1
M2
M2
M3
M3
M4
M5
M5
M6
M6
WKM Flight Controller
M1 M2 M3 M4 M5 M6
M1 M2 M3 M4 M5 M6
the ESC Signal Outlet R
L IN
Connecting the flight controller and landing gear
1. Connect the left servo (between M3 and M4) cable to the “L” port of the landing gear control board. 2. Connect the right servo (between M5 and M6) cable to the “R” port of the landing gear control board. 3. For the A2 flight control system, connect the F1 port of the flight controller to the “IN” port of the landing gear control board. Other flight control systems connect a 2-position channel receiver to the “IN” port.
L IN
M1 M2 M3 M4 M5 M6 M7 M8
LINK
LED
F4 F3 F2
F1 F1 X3 X2 X1
CONTROLLER UNIT
CAN1 CAN2
ANT
R
S2 S1
R Right Servo Connector
IN
Left Servo Connector
If right and left servo cables are reversed, the landing gear will not function properly. F1 Connect all wires carefully and neatly to avoid cable damage caused by frame edges.
LINK
LED
F4 F3 F2 F1 X3 X2 X1
CONTROLLER UNIT
CAN1 CAN2
ANT
M1 M2 M3 M4 M5 M6 M7 M8
L
S2 S1
R
L
IN
© 2016 DJI. All Rights Reserved.
15
Mounting Electronics and Wiring
M4
Connecting XT60 Ports on the Center Frame The bottom board is a power distribution board with three XT60 connectors for battery power.
Instructions
1. Connect the PMU power cable to the XT60 connector on top of the bottom board. 2. Connect the landing gear control board cable to the XT60 connector on the bottom of the bottom board. 3. Other connectors can supply power for other DJI devices, as required.
V-SEN
2S 6S
3V@5V
PM U
X1
PW (2V@6V)
Connecting XT60 Ports on the Center Frame / Installing Battery
Installing Battery Soldering battery connectors
AS150 spark-proof connectors are used. They must be soldered to your battery power cables. 1. Remove the original battery connectors. Avoid cutting the power and ground cables at the same time, as this can cause a short circuit. We recommend wrapping unsoldered cables with insulating tape to prevent accidental connections. 2. Pass the black ground wire through the black housing. After passing the wire through, solder the female bullet connector to the ground wire. Wait for the soldered connection to cool, then pull the housing back over the bullet connector. 3. Screw and pass the red power wire through the red housing. After passing the wire through, solder the male bullet connector to the power wire. Wait for the soldered connection to cool, and then screw and pull the housing back over the bullet connector.
16
Connectors soldering diagram © 2016 DJI. All Rights Reserved.
Spreading Wings S900 User Manual
Connectors are soldered
Installing and connecting battery
Inspect the surface of the battery connectors regularly. Replace connectors with signs of blackening due to oxidation. Failure to do so may lead to serious flight accidents.
© 2016 DJI. All Rights Reserved.
17
Installing Battery
1. Attach battery to battery tray. Do not use an oversized battery. Maximum installation dimension is 80mm X 120mm X 200mm. 2. Connect the black connector and then the red connector to power on. Disconnect the red connector then black connector to power off.
Setting Up the Landing Gear Using a 2-position RC transmitter switch, landing gear retraction can be carried out remotely. Setting up the transmitter Select a 2-position switch (default setting is OK) as the control input for the landing gear. Ensure the corresponding receiver port is connected to the “IN” port on control board. For the A2 flight control system, connect the flight controller’s F1 port to “IN” port on control board. Upper: Toggle the switch to this position to raise the landing gear.
Lower: Toggle the switch to this position to lower the landing gear.
Setting Up the Landing Gear If the transmitter switch has a FailSafe function, set the FailSafe value to the [Lower] position. This ensures that the landing gear will lower automatically when the receiver enters FailSafe mode. To avoid accidental switch triggering, slide levers or other controls can be used for landing gear control.
Usage procedures
1. Ensure transmitter and receiver batteries are fully charged. 2. Toggle the switch to the [Lower] position, and then turn on the transmitter. 3. Ensure the “R”, “L” and “IN” connections are correct. 4. Ensure the landing gear is in the [Lower] position, then power on the system. If a solid green LED on the landing gear control board lights up, everything is normal. If it flashes green slowly, re-calibrate the system according to instructions in “Recalibrating Servo Travel”. 5. Toggle the switch to the [Upper] position ONLY AFTER takeoff. 6. Toggle the switch to the [Lower] position for landing.
18
© 2016 DJI. All Rights Reserved.
Spreading Wings S900 User Manual
Servo power will shut off 3 seconds after the landing gear has reached its target position. When powering on the system, if the transmitter switch is in the [Upper] position, the LED will flash red quickly as a warning. Toggle the switch to the [Lower] position to continue. If there is an abnormal signal or no signal input into the “IN” port, the LED will slowly flash red. Check receiver and connections for problems. If servo power consumption is too high, the LED will light up red. If this lasts more than 4 seconds, the landing gear will lower and the LED will flash green slowly. Re-calibration is needed before flying. A2 flight control system users can use the A2 Assistant to set intelligent gear on the “Advanced” page. Refer to the “A2 user manual” for details.
LED Control Board Indicator System normal
— Solid green.
Calibration required
Blinks rapid green.
Recalibration required Calibration failed
Setting Up the Landing Gear
Blinks slow green. — Solid yellow.
Enter calibration mode
Blinks rapid yellow.
System calibrating
Blinks slow yellow.
Motor stalled
— Solid red.
Unsafe startup alert
Blinks rapid red.
Input signal abnormal
Blinks slow green.
Landing Gear Specifications Parameter
Range
Parameter
Range
Working Voltage
3S~6S (LiPo)
Input Signal
PWM (High-Pulse Width 800us~2200us)
Working Current
Max 1A@6S
Output Signal
PWM (Mid Position is 1520us) in 90Hz
Working Temperature
-20~70° C
Output Voltage
6V
Total Weight
875g
Servo Travel
150° (Minimum 120° )
© 2016 DJI. All Rights Reserved.
19
Mounting the Gimbal Before assembling the gimbal, install the GCU as shown below. Be sure to install on the side as shown below. A DJI Z15-GH4 (HD) gimbal has been used as an example in the following diagrams.
Mounting the Gimbal
The connectors on gimbal should be removed for better performance, then the gimbal can be mounted to the lower connection points. Users of DJI Z15-5N / 7N gimbal, refer to the DJI Z15-5N / 7N Gimbal Mounting Notes (Page 21) for details.
20
© 2016 DJI. All Rights Reserved.
Spreading Wings S900 User Manual
Check that the system’s center of gravity is on the line as shown in the diagram below.
Due to the size restriction of the Z15-5N / 7N gimbal, users should purchase extended landing gear legs (used with Z15-5N / 7N gimbal) to avoid damage and/or failure during the self-test. Refer to the Part List Package No.34 (Page 31) for details. Follow the Mounting the Landing Gear (Page 6) instructions to mount extended landing gear legs. Then the gimbal can be mounted as shown below. Package No.34 is for users whose landing gear legs are 300mm. Users whose landing gear legs are 350mm have no need to purchase this part.
© 2016 DJI. All Rights Reserved.
21
Mounting the Gimbal
DJI Z15-5N / 7N Gimbal Mounting Notes
Appendix ESC Sound ESC State Ready Throttle stick is not at bottom
Sound 1234567--B--B BBBBBB…
Input signal abnormal
B- - - - - - - - B- - - - - - - - B…
Input voltage abnormal
BB- - - BB- - - BB- - - BB…
ESC LED ESC State
LED
Standby
Off
Motor rotating
Solid Red or Green On
Motor rotating at full throttle position
Solid Yellow On
Appendix
DJI ESCs are specifically designed for multi-rotors. When used with DJI autopilot systems parameters and travel ranges do not have to be calibrated.
Specifications Frame Diagonal Wheelbase
900mm
Frame Arm Length
358mm
Frame Arm Weight (with Motor, ESC, Propeller )
316g
Center Frame Diameter
272mm
Center Frame Weight (with Landing Gear Mounting Base, Servos)
1185g
Landing Gear Size
460mm(Length)×450mm(Width)×360mm(Height)
Motor Stator Size
41×14mm
KV
400rpm/V
Max Power
500W
22
© 2016 DJI. All Rights Reserved.
Spreading Wings S900 User Manual
Weight (with Cooling Fan)
158g
ESC Working Current
40A
Working Voltage
6S LiPo
Signal Frequency
30Hz ~ 450Hz
Drive PWM Frequency
8KHz
Weight (with Radiators)
35g
Foldable Propeller (1552/1552R) Material
High strength performance engineered plastics
Size
15×5.2 inch
Weight
13g
Flight Parameters 4.7Kg ~ 8.2Kg
Total Weight
3.3Kg
Power Battery
LiPo (6S,10000mAh~15000mAh,15C(Min))
Max Power Consumption
3000W
Hovering Power Consumption
1000W (@6.8Kg Takeoff Weight)
Hovering Time
18min (@12000mAh & 6.8Kg Takeoff Weight)
Working Environment Temperature
-10° C ~ 40° C
Appendix
Takeoff Weight
Gain Value Settings
Flight Control
Basic
Attitude
Pitch
Roll
Yaw
Pitch
Roll
Vertical
A2
110%
110%
120%
220%
220%
120%
WooKong-M
160%
160%
160%
190%
190%
100%
© 2016 DJI. All Rights Reserved.
23
FAQ Soldering the ESC Be sure to solder the thick wires and fine wires correctly when soldering an ESC to the frame arm. Clockwise (CW) and counter clockwise (CCW) motors have a different arrangement of the colored wires.
G
G
G
G
P
P
V
V
Red Black Blue Thick wire Fine wire Fine wire
Solder pad Blue Black Red
Thick wire
CCW arms
CW arms
Remounting the Propellers Instructions
1. Use two M3×12.3 screws and four washers to remount propellers. 2. Apply thread locker to the thread of the propellers mount first. 3. Affix screws with 4Kg ∙ cm (0.4N ∙ m) torque. FAQ
Refer to original screw tensions if you are unfamiliar with torque measurements. Applying thread locker to the propeller mount first avoids getting thread locker into the holes of the plastic propeller. Loose screws cannot be securely locked with thread locker.
Propeller Precautions Torque markers on the screws and propeller covers will give you a visual cue to check whether the propellers are loose. Check the torque markers before every flight.
24
© 2016 DJI. All Rights Reserved.
Spreading Wings S900 User Manual
Using the Propeller Holder Instructions
1. Insert the propeller blades into the propeller holder. 2. Attach the propeller holder to the frame arm.
Assembling Motor Vibration Absorbers A soft damper is part of the vibration absorber. Assemble soft dampers as shown below. Assembly is the same for CCW and CW propellers. FAQ Ensure all soft dampers and vibration absorbers are in good condition before every flight. If not, replace immediately. Otherwise, the flight performance of your aircraft will be adversely affected. Before installing the soft dampers, put the copper gaskets onto the four mounting holes on the carbon plate. Then put the soft dampers into the mounting holes. After tightening the screws, the vibration absorbers may be twisted. If this is the case, hold the motor with your thumbs under the base plate and fingers on the top carbon plate, and squeeze the plates together to make the vibration absorbers flat and parallel with the plates.
© 2016 DJI. All Rights Reserved.
25
Spreading Wings S900 User Manual
Remounting the Landing Gear Servo Remounting servos is not recommended as they are pre-installed.
Instructions
1. Connect the left servo cable to the “L” port of the landing gear control board. 2. Connect the right servo cable to the “R” port of the landing gear control board. 3. Press and hold the SET button using a pin then power on. You will see a yellow LED beside the SET button flashing quickly. Wait as servos complete position initialization. 4. Make sure the arm connecting to the servo is parallel to the link as shown in the following diagram. 5. Assemble the left and right servos to the left (between M3, M4) and the right (between M5, M6) parts of the landing gear. Power off.
R
L IN
Servo
To right servo
Connecting arm
To left servo
Link
To receiver channel (To F1 port if use A2) SET Button LED
After Installation
Recalibrating Servo Travel Instructions
1. Keep your hands away from all moving parts. 2. Ensure the “R”, “L” and “IN” connections are correct. 3. Keep the whole aircraft off of the ground during calibration, as landing gear will move. 4. Press and hold the SET button using a pin while powering on, then release. An LED will flash yellow quickly. Press the SET button again. Auto calibration will begin and the LED will flash yellow slowly. DO NOT obstruct any moving parts during auto calibration. 5. During calibration, the left landing gear will raise and lower, followed by the right landing gear. 6. After calibration, both the left and right landing gears will be lowered and the LED will display a solid green light. This indicates that the landing gear is working properly. If the LED is solid yellow after calibration, a problem has occurred. Carry out the instructions in “Remounting the Landing Gear Servo” then try again. Avoid obstructions during calibration. If the landing gear was obstructed, recalibration will be required, per the above steps. If the “R” and “L” servo cables are reversed, travel will not be measured correctly. Fix the connections and recalibrate the landing gear using the above steps. Landing gear travel has been pre-calibrated. Mechanical adjustment of the gear travel is not recommended.
26
© 2016 DJI. All Rights Reserved.
Part List If you require a replacement part, locate the part that you wish to replace in the following tables. Then order the package that comes with the specified part. The numbering of the part is defined as follow:
S900 01-Frame Arm；02-Center Frame； 03-Landing Gear
S9020101CCW
Package Part No. Package No.
Frame Arm
S9012102B/ S9012202R/ S9013701R/ S9013801B
M3x12.3 (hexagan)
S9012503
S9012501CCW/ S9012502CW S9012101B/ S9012201R
M3x10.3 S9012903/ S9013003/ S9013103/ S9013203
S9010801/ S9013501 S9010802 S9011001
S9010401CCWB/ S9010501CCWR/ S9010601CWB/ S9010701CWR
M3x4.5 S9012902/ S9013002/ S9013102/ S9013202
S9010402/ S9010502/ S9010602/ S9010702
S9010403/ S9010503/ S9010603/ S9010703
M3x12.3 (cheese)
S9012301R/ S9012401G
Package No. Name S900 Frame Arm CCW - Black
Part No. S9010401CCWB, S9010402, S9010403, S9010404, M3×12.3 (cheese)
5
S900 Frame Arm CCW - Red
S9010501CCWR, S9010502, S9010503, S9010504, M3×12.3 (cheese)
6
S900 Frame Arm CW - Black
S9010601CWB, S9010602, S9010603, S9010604, M3×12.3 (cheese)
7
S900 Frame Arm CW - Red
S9010701CWR, S9010702, S9010703, S9010704, M3×12.3 (cheese)
8
S900 Motor Damping Unit
S9010801, S9010802, M3×10.3
10
S900 Motor Mount Carbon Board
S9011001, M3×4.5 © 2016 DJI. All Rights Reserved.
27
Part List
S9010404/ S9010504/ S9010604/ S9010704
S9012302/ S9012402
S9012901/ S9013001/ S9013101/ S9013201
4
CW as clockwise ； CCW as counter clock wise ； B as Balck ； R as Red ； G as Green
Spreading Wings S900 User Manual
21
S900 4114 Motor with black Prop cover
S9012101B, S9012102B, M3×4.5
22
S900 4114 Motor with red Prop cover
S9012201R, S9012202R, M3×4.5
23
S900 ESC with Red LED
S9012301R, S9012302, M3×12.3 (cheese)
24
S900 ESC with Green LED
S9012401G, S9012402, M3×12.3 (cheese)
25
S900 Propeller Pack
S9012501CCW, S9012502CW, S9012503, M3×12.3 (hexagan)
Center Frame
S9020301
M2.5x8 (cheese) S9021502 S9021503/ S9032703 M3x6.5
Part List
S9021501
S9020302 S9020901
S9021201L
M3x8 (self-tapping)
S9021202R
S9021203/ S9021101
S9021401
M2.5x8 (cheese)
M3x6.5
28
© 2016 DJI. All Rights Reserved.
Spreading Wings S900 User Manual
Package No. Name
Part No.
3
S900 Lock Knob
S9020301, S9020302, M3×8 (self-tapping)
9
S900 Center Frame Support Pillar
S9020901, M2.5×8 (cheese)
12
S900 Arm Mounting Bracket
S9021201L, S9021202R, S9021203, M3×6.5
14
S900 Center Frame Bottom Board
S9021401, M3×4.5 (cheese), M3×8 (selftapping), M3×6.5, M3×5.5
15
S900 Center Frame Top Board
S9021501, S9021502, S9021503, M3×6.5, M2.5×8 (cheese)
11
S900 Frame Arm Mounting Steel Shaft
S9021101
Landing Gear M3x4.5 S9031812
S9031902
S9031712
S9031814 S9031815
S9031903 M3x6.5 S9031904 S9031905
M3x6.5 S9031901 M2.5x13 S9031604/ S9033306 S9031602/ S9033303 S9033301 S9033302 S9031603/ S9033305 S9031601/ S9033304 S9031605/ S9033307
S9031701 M2.5x10 (socket cap)
S9033314
M2.5x5
S9031801
M2.5x8 (cheese) S9033308 S9033309 S9033310 S9033311 S9033312 S9031713/ S9031813 M2.5x8 (socket cap) S9032601
M3x8 S9032605
S9031802 S9031803 S9031804 S9031805 M2.5x8(cheese)
S9031808 S9031809 M1.6x5 S9031810 S9031811
M2.5x8 (socket cap)
(1)
S9031806 S9031807 M3x6.8 S9032001 S9032002
S9032602 S9032603 S9032606 M3x22 (socket cap)
Caution (1) Parts within the dotted box are mirrored against each other. Except for S9031814 and S9031815.
S9032604
© 2016 DJI. All Rights Reserved.
29
Part List
S9030201 S9033313
Spreading Wings S900 User Manual
Package No. Name 16 17
Part No.
S900 Gimbal
S9031601, S9031602, S9031603, S9031604, S9031605,
Damping Bracket
M2.5×5, M2.5×13
S900 Retractable
S9031701, S9031702, S9031703, S9031704, S9031705,
Module (Right)
S9031706, S9031707, S9031708, S9031709, S9031710, S9031711, S9031712, S0031713, M1.6×5, M2.5×10 (socket cap), M2.5×8 (cheese), M2.5×5, M3×8, M3×4.5, M3×6.8
18
S900 Retractable
S9031801, S9031802, S9031803, S9031804, S9031805,
Module (Left)
S9031806, S9031807, S9031808, S9031809, S9031810, S9031811, S9031812, S9031813, S9031814, S9031815, M1.6×5, M2.5×10 (socket cap), M2.5×8 (cheese), M2.5×5, M3×8, M3×4.5, M3×6.8
19
S900 Gimbal
S9031901, S9031902, S9031903, S9031904, S9031905,
Damping
M2.5×5, M3×6.5
Connecting Brackets
Part List
20
S900 Landing Skid
S9032001, S9032002
26
S900 Landing Gear
S9032601, S9032602, S9032603, S9032604, S9032605,
Leg
S9032606, M2.5×8 (socket cap), M3×22 (socket cap)
2
S900 Battery Tray
S9030201
33
S900 Gimbal
S9033301, S9033302, S9033303, S9033304, S9033305,
Mounting
S9033306, S9033307, S9033308, S9033309, S9033310,
Accessories
S9033311, S9033312, S9033313, S9033314, M2.5×5, M2.5×13, M2.5×8 (cheese)
Miscellaneous S9020201
S9013601
S9020202
S9032701
S9032702 S9020103
S9033401
Caution: This part is used with Z15-5N / 7N gimbal.
30
© 2016 DJI. All Rights Reserved.
S9020104
Spreading Wings S900 User Manual
Package No. Name
Part No.
13
S900 Center Frame
Package 3, 9, 12, 14, 15
29
S900 Complete Arm [CW-RED]
Package 7, 8, 10, 11, 22, 23, 25, S9012901, S9012902, S9012903
30
S900 Complete Arm [CW-Green]
Package 6, 8, 10, 11, 21, 24, 25, S9013001, S9013002, S9013003
31
S900 Complete Arm [CCW-RED]
Package 5, 8, 10, 11, 22, 23, 25, S9013101, S9013102, S9013103
32
S900 Complete Arm [CCW-Green]
Package 4, 8, 10, 11, 21, 24, 25, S9013201, S9013202, S9013203
27
S900 GPS Holder
S9032701, S9032702, S9032703, M2.5×8 (cheese)
28
S900 Screw Pack
Assorted screws
1
S900 Power Cord Plug
S9020101, S9020102, S9020103, S9020104
34
S900 Extended Landing Gear Leg
S9033401
35
S900 Rubber Damper for 4114 Motor
S9013501, M3×10.3
36
S900 Propeller Holder
S9013601
37
S900 4114 Motor-Red Prop Cover
S9013701R, M3×12.3 (hexagan)
38
S900 4114 Motor-Black Prop Cover
S9013801B, M3×12.3 (hexagan)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
© 2016 DJI. All Rights Reserved.
31
FCC Statements
FCC Statements
The content is subject to change.
Download the latest version from http://www.dji.com/product/spreading-wings-s900 If you have any questions about this document, please contact DJI by sending a message to
[email protected]. © 2016 DJI. All Rights Reserved.
