Sprint 5000 Om

Transcript

SPRINT 5000 BOOKLETMAKER OPERATION MANUAL Sprint5000HCS-USA.doc3.doc Page 1 01/05/2002 CONTENTS 1. Introduction. 2 2. Specification. 2 3. Initial setting up. 3 4. Operation. 4.1 4.2 4.3 4.4 4.5 4.6 Loading staples. Staple out system. Staple jam. Paper width settings. Stapling / folding positions. Changing stapling head positions. 4 5 7 7 8 9 11 5. Booklet making. 12 6. Corner and edge stapling. 14 7. Counter. 17 8. Replacing stapling heads. 17 9. Aligning of stapling heads. 17 10. Problem solving. 18 Appendix A: Parts lists and drawings. MBM Corporation Michael Business Machines 3134 Industry Drive North Charleston South Carolina 29418 Customer Service - Tel: (800) 223 2508 Fax: (803) 552 2974 Parts & Service - Tel: (800) 223 2508 Fax: (803) 760 3814 Sprint5000HCS-USA.doc3.doc 1 Page 2 01/05/2002 INTRODUCTION • The Sprint 5000 Bookletmaker centre staples and folds to make booklets between 4” x 5½“ and 8½“ x 11” with up to 80 pages. On each cycle of the machine one set of sheets is stapled and the preceding set is folded and stacked on the conveyor belt. • It is also possible to edge and corner staple up to 20 sheets. • The machine can either be hand fed or placed on-line to one of the various desktop vertical collators, using a KAS conveyor/ jogger link. A stand is also supplied to carry the collator so that it is the correct height for feeding into the Bookletmaker. • The Sprint 5000 is a floor standing machine fitted with sturdy castors and an integral conveyor which can be folded up in order to occupy minimal floor space when not in use. • This model has five stapling positions to which the stapling heads can be moved according to the size of paper. The right hand outside position is for corner stapling. • A Staple Out Detector is fitted to each of the stapling heads, and the Bookletmaker will stop when the stapling head runs out of staples. 2 SPECIFICATION INPUT CAPACITY: Booklets Pads 20 sheets of 20 lb bond 20 sheets of 20 lb bond SHEET SIZES: Booklets Pads 5½“ x 8” to 11½“ x 17½“. 8½” x 11½“ STAPLES 5000 staple cartridge DIMENSIONS Width 23” Height 36” Length 20” (Conveyor stored). Length 46” (Conveyor in use). WEIGHT 205 lbs. POWER 115v 60Hz Consumption approx. 180 Watts Fuse: 10 amp 115v. Sprint5000HCS-USA.doc3.doc 3. Page 3 01/05/2002 INITIAL SETTING UP 1. Remove the bolts holding the machine to the pallet. 2. Castors are already fitted to the machine, lift from the pallet on to an even surface. 3. Remove packing from stapling section and from under fold stop beneath the conveyor. 4. Lower output conveyor, allowing the slotted ends on the support bars (part no. 6.06) to locate on the protruding bolts provided. These bolts are located at the base of the machine. 5. When making books, one need only fit the conveyor wheels (part no.6.13) and make sure that the divert plate (part no. 3.71) shown in figure 2 is pushed forward. Figure 1 - Conveyor setup. 6. Insert the conveyor end stop (part no. 6.11) at the far end of the conveyor, making sure it does not infringe the belt. It is held in position by a flat magnet. 7. Position the machine near to a suitable socket outlet and ensure outlet is not covered and is easily accessible. 8. Check that the power supply is of the correct voltage for the machine. Once connected, the machine is ready for use. Sprint5000HCS-USA.doc3.doc 4. Page 4 01/05/2002 OPERATION 13 1 44 A3 40 38 36 34 32 12 A4 28 26 24 2 22 A5 20 18 16 11 14 12 10 3 4 4 10 5 9 8 7 14 Figure 2 - Control layout 1 2 3 4 5 6 7 Fold stop lock thumbscrew Stapling head position arm Edge staple stop thumbscrew Side guide clamping thumbscrew Staple low indicator / reset Anvil 8 9 10 11 12 13 14 Staple position fine adjustment screw On / off button Staple delay knob Staple/fold stop indicator Fold stop tilt adjustment thumbscrew Staple & fold stops adjustment wheel Counter Sprint5000HCS-USA.doc3.doc Page 5 01/05/2002 4.1 Loading Staples : 1. Only those staples sold or recommended by your supplier should be used in the Sprint 5000 Bookletmaker. Use of non recommended staples may damage the stapling heads and they are not covered by any warranty. 2. Raise the top cover. 3. Raise metal locking bar upwards and remove spent cartridge. Ensure the bar is in the uppermost position otherwise the cartridge may not load properly. 4. Make sure that staples do not protrude past the staple tear line. If necessary the staples are easily torn off at the tear line by tearing downward. 5. Cartridge should be placed flat on the slide in the body of the stapler and pushed firmly forward. Do not allow the cartridge to move backwards once inserted into the stapler. If this occurs remove cartridge from stapler and tear off staples at tear line again before re-inserting. 6. To keep the cartridge in place push metal locking bar down until it snaps into the grove on the back of the cartridge. 7. Press staple out reset button, lower top cover. 8. The staples do not immediately feed through to the plunger and therefore the machine will not staple during the first three or four cycles after loading. Where this is a problem, refer to 9 and 10 below. 9. Turn off staple out detector (select the centre position on the three-way toggle switch, see 4.2) 10. To avoid books being processed without staples, cycle the machine by placing scrap paper beneath the heads. Repeat this until staples appear in the paper. 11. Turn on staple out detector and continue producing books. Sprint5000HCS-USA.doc3.doc Page 6 Figure 3 - Staple Out reset/indicators. 01/05/2002 Sprint5000HCS-USA.doc3.doc Page 7 01/05/2002 4.2 Staple Out System : This is switched on and off using a three-way toggle switch located on the inside left-hand side wall underneath the shelf. Select the switch position as follows. 1. With the toggle switch is in the central position the staple out detectors on both heads are off. 2. With the toggle switch pushed downwards both staple detectors are on. 3. When the toggle switch is pushed to it’s furthest position upwards only the staple out detector on the right-hand head is on (corner stapling). The above is displayed on the legend plate around the switch (shown in figure 8.). When the stapling head runs out of staples the red light pertaining to that head will illuminate and the booklet maker will not cycle. The last set will not be stapled and should be removed from the fold section. It can be reprocessed once the staple head(s) has been refilled. 4.3 Staple Jam : To clear jammed staples from heads, it is best to remove the cartridge, clear any damaged staples from stapling head and anvil, and replace the cartridge as described in 4.1. WARNING - One may clear the jammed staples by operating the plunger manually. In this instance take care not to put fingers under front-most portion of stapling head, so avoiding injury to fingers from staples being ejected from the head. Sprint5000HCS-USA.doc3.doc Page 8 01/05/2002 4.4 Paper Width Settings: 1. Both sides guides should be adjusted for a given size of paper. Loosen the thumbscrews and move the side guides until their outside edges are level with the marking on the scale corresponding to the width of the paper, and then re-tighten the thumbscrews so that the guides are held in place. Figure 4 - Side guides. 2. Note that the marked settings are meant to be wider than the paper, to allow for side jog. Both guides move inwards on each cycle to the correct width to ensure that the sheets are aligned before stapling occurs. 3. When corner and edge stapling 8½“ x 11” paper, feeding landscape, the guides are set to the 11“ x 17” markings. Sprint5000HCS-USA.doc3.doc Page 9 01/05/2002 4.5 Stapling / Folding Positions : 1. The Stapling and the Folding positions are adjusted as one. thumbscrew, figure 5. Loosen fold stop lock 2. Turn the fold stop adjustment wheel until the staple stop aligns with the appropriate calibration on the scale, for the size of paper being used. Figure 5 - Fold stop 3. Re-tighten fold stop lock thumbscrew when the stop has been correctly positioned. Sprint5000HCS-USA.doc3.doc 4. Page 10 01/05/2002 If fold line is not perpendicular to booklet edges, this can be corrected by adjusting the fold stop tilt thumbscrew, figure 6, on the left-hand side of the fold stop adjusting shaft. Loosen the locking nut and turn the thumbscrew clockwise to raise the left-hand end of the fold stop, or anti-clockwise to lower. Tighten locking nut. Figure 6 - Fold stop tilt. Sprint5000HCS-USA.doc3.doc Page 11 01/05/2002 4.6 Changing stapling head positions. 1. To move the stapling heads to the alternative positions, lift the stapling head position arm, figure 7, then slide the entire stapling unit to the new position. 2. When moving the stapling head, hold the slide bracket at the retaining plate end, and move to new position. 3. Drop the position arm into the new slot on slide bracket, which will align the stapling head in the new position. Staple head position arms Slide bracket Figure 7 - Stapling head adjustment and anvil positions 4. Positions are provided for the various sized books between 4” x 5½“ and 8½“ x 11” paper, with an additional position on the far right for corner stapling 8½“ x 11”. Sprint5000HCS-USA.doc3.doc 5. 1. Page 12 01/05/2002 BOOKLET MAKING. The machine will not operate with the top safety cover in the raised position. After closing the top safety cover it is necessary to press the circuit reset button, located in the left hand inside side wall. This is an added safety feature and the machine will not cycle until the button is pressed. Figure 8 - Operating controls 2. When the machine is switched on the motor will not start until the first set of paper is placed in the machine. If it is left running and not used for a period of more than three minutes the motor will automatically switch off. The motor will re-start when paper is placed in the machine. 3. The stapling / folding operation is started when sensors detect the paper in the machine. The time between the paper entering the machine and the stapling action can be varied. This is achieved by turning the Stapling Delay Control shown in figure 8 clockwise for more time and anti-clockwise for less. When first using the machine, give the Stapling Delay Control a quarter turn clockwise. This will give time for the operator to settle the paper between the guides before the machine cycles. Sprint5000HCS-USA.doc3.doc Page 13 01/05/2002 Sprint5000HCS-USA.doc3.doc Page 14 01/05/2002 4. When paper is placed in the machine it breaks the light beam between the photocell emitter (part no. 2.83) and the photocell receiver (part no. 2.71). On the interruption of the beam the time set by the timer expires and the machine will operate for one cycle. 5. If the stapled set fails to drop into the folding position the guides may be set too closely and must be set slightly wider. The first set placed in the machine will not fold and exit to the conveyor until the second set is being stapled. To release the last set from the machine, hold a scrap of paper under the stapling heads for one cycle and then remove it. 6. The conveyor wheels shown in figure 11 should be adjusted so that the wheels are just over a book’s distance from the fold rollers. Too close and they will interfere with subsequent booklets coming out of the fold rollers. If the wheels are too far away the booklets will have the tendency to insert themselves inside previously ejected booklets. 7. Staple Position Fine Adjustment. If, after correctly setting the fold stop adjustment wheel, it is found that the staples are not exactly on the fold line, this can be corrected by turning the staple position fine adjustment screw, figure 9. Figure 9 - Staple position fine adjustment Looking at the finished booklets laying on the stacker table after ejection from the fold rollers, if the staples are visible above the fold, turn adjusting screw anti-clockwise. If the staples are below the fold, turn adjusting screw clockwise. Sprint5000HCS-USA.doc3.doc 6. Page 15 01/05/2002 CORNER AND EDGE STAPLING Refer to figure 10. 1. Open the top perspex cover. Move the paper width guides to the position where they will side jog the set of paper without impeding its path through the machine. For 8½“ x 11” paper, set the guides to the 11“ x 17” markings. 2. For edge stapling, select the desired pair of anvil positions. When corner stapling move the right hand stapling head to the furthest right position, and remove the staple cartridge from the left hand stapling head. Then move the left- hand stapling head and lock it down in position where it is not over an anvil. Alternatively one could also remove the left-hand stapling head as described in section 8 concerning replacing stapling heads. 3. Turn the corner/edge stop adjust thumbscrew, located in the second paper table shown in figure 10 to the right of the right-hand paper width guide, anti-clockwise. The stop will rise just behind the Anvil bar. Figure 10 - Corner/Edge stops. Sprint5000HCS-USA.doc3.doc 4. Page 16 01/05/2002 Push the divert plate (part no. 3.71) back against the Top front plate (part no. 3.42), figure 11. This will divert the set of paper away from the folding section and out of the machine. Figure 11 - Conveyor setup 1. 5. Fit the deflector plate, by fitting its hook over the tie bar, so that it rests on the outfeed conveyor. 6. Move the conveyor wheel support brackets which are held in place by thumbscrews, so that the edge nearest the main body of the machine is approximately 6” from the start of the conveyor. Figure 12 shows which way round they are fitted. Sprint5000HCS-USA.doc3.doc Page 17 01/05/2002 Figure 12 - Conveyor setup 2. 7. Place the conveyor wheel spindle (part no. 6.17) into the slots provided in the conveyor wheel support brackets. 8. As a set exits the machine down the Exit plate it should first come to a stop so that approximately 1” of the tailing edge is still resting on the raised upper portion of the Exit plate. During the next cycle that set will drop down to the next level avoiding the following set which will lay on top. 9. Ensure that the appropriate stapling head(s) is loaded, and the staple cartridge firmly pushed home. If staple out system is in use, press the staple out reset button. Close Perspex cover. 10. When hand feeding, insert the set to be stapled into the machine, underneath the stapling heads, until the leading edge touches the paper stops. The machine will cycle, when the sensors detect the paper, taking the set through the machine. 11. When on-line to a desk top collator, running 8½“ x 11” paper, using a KAS conveyor/ jogger the link bracket should be fitted using the 11“ x 17” bookletmaking slot. The back jogger should also be in the 11“ x 17” position. Sprint5000HCS-USA.doc3.doc 7. Page 18 01/05/2002 COUNTER The counter can be reset to '0000' by pressing the rectangular black button below the number window. 8. REPLACING STAPLING HEADS Should it become necessary to remove either or both of the stapling heads follow the procedure below. 1. Pull the left-hand side of the spring clip so that the eye clears the pin and swivel the spring clip anti-clockwise around the actuating bar. This should remove the hook on the right-hand side of the clip from the other end of the pin. 2. Unplug the electrical lead from the bracket containing the reset button and lights. 3. Loosen the small (M6) bolt in the stapling head retaining plate sufficiently so that the retaining plate can be lifted and pushed aside revealing the trough in which the bar at the back of the stapling head is located. 4. Take the bar from the trough and having removed the head completely replace the retaining plate in it’s original position and tighten the bolt. 5. To re-fit a new head place the bar at the back of the stapling head into the trough, position the retaining plate over the top and tighten the bolt and replace the spring clip. Replace electrical lead. 9. ALIGNING OF STAPLING HEADS Replacement stapling heads may be fitted to the Bookletmaker. If the replacement head is giving a bad staple, then remove power from the machine and re-align the head as below. 1. Remove cassette of staples from stapler. 2. Loosen the hex screws holding part no. 2.105 3. Place the adjustment guide between stapler and anvil. Align and insert the raised lugs of the guide into the underside of the stapler where the staple exits, making sure the metal locating pip is to the front. When inserted replace the cassette of staples. Sprint5000HCS-USA.doc3.doc 4. Page 19 01/05/2002 Locate pip on adjustment guide into small hole at front of anvil and then retighten hex screws. The stapling head should now be in a position to carry on stapling after removing adjustment guide. Sprint5000HCS-USA.doc3.doc 10. Page 20 01/05/2002 PROBLEM SOLVING. PROBLEM Motor will not start POSSIBLE CAUSES Blown Fuse REMEDY Switch off and unplug machine. Check and replace fuses as necessary Machine will not start Powerful light source from Shield safety cover from light or when paper is inserted above move machine Machine will not cycle Machine in jam mode Stapling head jammed Incorrectly cartridge fitted Remove paper from machine in stapling section to allow photo-cell to reset staple Switch off machine, lift safety cover, remove cartridge, clear jammed staples and replace. Repeated jamming of Miss aligned head with anvil stapling head. Check alignment of stapling head and anvil. Staple legs breaking. Check alignment of stapling head and anvil. Miss aligned head with anvil One staple not on fold Fold stop out of line line Adjust tilt screw Book does not travel Side guides too tight through machine after stapling Open right hand side guide Pinching around staples Clean rollers Residue being left on rollers Sprint5000HCS-USA.doc3.doc Page 21 01/05/2002 Appendix A Spare parts drawings for the Sprint 5000 Bookletmaker C5003-FC 4.97 LHS 11 12 1 10 9 8 4 3 6 RHS 5 7 240 V 3A 2 15 14 1. Panels C5000-1a 5.97 kf_5002.xls 01/05/2002 5000HCS/ Part Quantity 1.00 PANELS 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 Side Cover Bottom Front Plate Top Front Plate Counter (not in view). State 240vAC or 24vDC Fuse Holder Fuse Switch - Staple count Staple delay knob Reset Switch Power Switch Side Cover Perspex Cover 1 1 1 1 2 2 1 1 1 1 1 1 Motorised Interface Unit socket (24v DC output) 240v/110v AC output socket Trimmer On-line socket Collator On-line socket 1 1 1 1 Please quote machine model and serial number, with part number, on order. 81 82 85 86 137 87 138 139 83 136 80 1 78 110 140 77 2 7 RHS 135 8 134 108 133 9 109,107 6 132 10 70 105 122,67 104 64 68 71 11 69 12 65 63 131 13 14 62 60 59 58 61 57 88 89 56 48 55 46 47 17 18 16 103 54 102 24 90 19 26 28 20 29 101 LHS 30 31 51 50 33 100 99 39 98 35 37 36 32 34 96 95 94 93 43 42 41 40 91 121 120 119 118 117 116 115 2. Staple section 114 113 112 111 C5002-2c cdr 8.99 kf_5002.xls 01/05/2002 5000HCS/ Part Quantity 2.00 STAPLE SECTION 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 2.19 2.20 2.21 2.22 2.23 2.24 2.25 2.26 2.27 2.28 2.29 2.30 2.31 2.32 2.33 2.34 2.35 2.36 2.37 2.38 2.39 2.40 2.41 2.42 2.43 2.44 2.45 2.46 2.47 2.48 2.49 2.50 2.51 2.52 2.53 2.54 2.55 2.56 2.57 Stapling head actuator Bar Top Takeaway Wheel - corner stapler 1 1 Corner/Edge Stop adjust thumbscrew Side Guide RHS Scale RHS Paper Table Scale LHS Bearing Housing Side Jog Shaft RHS Bottom Takeaway Wheel - corner sta. Bearing Block 1 1 1 1 1 1 1 1 2 Timing Pulley Collar Shaft Cup Bearing Front Shaft for Paper Stop Assembly 1 1 1 1 1 Paper Stop Frame Fine Adjustment Plate Timing Pulley Paper Stop Pivot Block Angle Spindle Collar Corner stop pivot arm Corner stop mount Collar Spindle Edge/corner stapling stop Link Arm Return Spring 1 1 1 1 1 1 1 1 1 2 1 1 1 1 Stapling stop sleeve Collar Cup Bearing Timing Belt - Takeaway drive Stapling Position Stop Belt 1 1 1 1 1 Side Jog Spring Collar Support Blocks 1 1 2 Collar Bearing Housing Washer Spacer Side Jog Shaft LHS Bearing Housing Collar Bottom Takeaway Shaft 1 1 1 1 1 1 1 1 Please quote machine model and serial number, with part number, on order. kf_5002.xls 01/05/2002 5000HCS/ Part 2.58 2.59 2.60 2.61 2.62 2.63 2.64 2.65 2.66 2.67 2.68 2.69 2.70 2.71 2.72 2.73 2.74 2.75 2.76 2.77 2.78 2.79 2.80 2.81 2.82 2.83 2.84 2.85 2.86 2.87 2.88 2.89 2.90 2.91 2.92 2.93 2.94 2.95 2.96 2.97 2.98 2.99 2.100 2.101 2.102 2.103 2.104 2.105 2.106 2.107 2.108 2.109 2.110 2.111 2.112 2.113 2.114 2.115 2.116 Quantity Collar Center Bearing Block Bottom Takeaway Wheel Side Guide Extension LHS Side Guide LHS Paper Deflector LHS Second Paper Table Side Guide clamping thumbscrew Anvil Anvil Bar Staple Stop Scale Side Guide Extension RHS (not shown) Paper Deflector RHS Photocell Receiver 1 1 1 1 1 1 1 2 2 1 1 1 1 1 Stapling head locking lever Bearing Housing Collar 2 1 2 Pivot Shaft Top Takeaway Wheel Lift Arm Top Takeaway Wheel Photocell Emitter 1 1 1 1 Staple Out Light Staple Out reset button Staple Out socket for interface lead (2.107) Staple centring adjustment screw block Staple centring adjustment screw Collar Control wheel 2 1 2 1 1 2 1 Belt support plate Spacer - short Spacer - long Clamping bolt 1 3 1 3 Bottom plate - runner assembly Top plate - runner assembly Slide plate - LHS Spacer - medium Slide plate - RHS Staple stop plate Staple head retaining plate Staple head capivating plate 1 1 1 2 1 1 2 2 2 2 2 2 2 1 1 1 1 1 2 Staple head interface lead Staple cartridge Staple head Staple head return spring clip Bottom Stop Bolt Rubber Stop Cam Lever Clinch Activator Plate Shaft Clinch activator Arms Please quote machine model and serial number, with part number, on order. kf_5002.xls 01/05/2002 5000HCS/ Part 2.117 2.118 2.119 2.120 2.121 2.122 2.130 2.131 2.132 2.133 2.134 2.135 2.136 2.137 2.138 2.139 2.140 2.141 2.142 Quantity Block Collar Cup Bearing Clinchers Clinch Spacer Plate Anvil Bar for Clinchers (replaces 2.67) 2 2 2 4 2 1 Centre guide (replaces 2.79) Stapling head universal bar (replaces 2.74) Slide bracket (replaces 2.106) - LHS Centre guide mounting block Slide bracket - LHS Staple head position arm - RHS Staple head position arm - LHS Protective rubber Carrier tube for emmitter (replaces 2.84) Smoother plate 1 1 1 1 1 1 1 2 1 1 Please quote machine model and serial number, with part number, on order. 89 87, 88 86 RHS REAR 85 84 2 1 4 3 91 78 16 17 19 20 21 22 23 77 83 76 6 82 75 7 81 74 8 80 73 9 79 13 15 11 24 18 3. Fold section 12 72 71 66 40 65 41 14 64 42 39 63 43 44 38 37 25 26 27 LHS 62 45 28 29 61 69 30 46 60 59 47 31 36 32 48, 49 57 50 33 FRONT C5002-3a 11.98 56 55 54 53 52 51 35 34 kf_5002.xls 01/05/2002 5000HCS/ Part Quantity 3.00 FOLD SECTION 3.01 3.02 3.03 3.04 3.05 3.06 3.07 3.08 3.09 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22 3.23 3.24 3.25 3.26 3.27 3.28 3.29 3.30 3.31 3.32 3.33 3.34 3.35 3.36 3.37 3.38 3.39 3.40 3.41 3.42 3.43 3.44 3.45 3.46 3.47 3.48 3.49 3.50 3.51 3.52 3.53 3.54 3.55 3.56 3.57 Staple & Fold stops adjust wheel Bearing Housing Fold Stop Tape Wheel Fold Stop Tilt Thumbscrew 1 1 1 1 Spacer Fold Stop Tilt Block Fold Stop Shaft Collar Knife crank assembly bolt Bearing Housing Knife In' Adjustment screw 'Knife In' Cam Roller Knife crank pivot bolt Collar Paper Stop Cam 'Knife In' Cam Block 'Knife In' Stop Blade 'Knife Out' Cam Roller 'Knife Out' Cam Block Timing Shaft Timing Collar Roller Microswitch Bearing Housing Collar Bearing Housing Knife Shaft Timing Pulley Rubber sleeve Knife Tie Bar Knife Frame Knife Blade Assembly Knife Pivot Lever Collar Knife pivot shaft Collar Knife adjustment screw Knife crank Knife operating assembly Clutch shaft Collar Bearing housing Top front plate Motor Plate Tie bar Knife Return Spring Plate Front angled bracket LHS Front angled bracket RHS Mains Inlet Cable Plug Fold Stop Retaining Mount Bottom front plate Fold stop guide Fold stop Castor Castor bar 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3 1 4 1 1 1 1 1 1 1 1 2 1 2 2 1 1 1 2 2 1 1 1 1 1 1 1 1 1 2 1 3 1 4 2 Please quote machine model and serial number, with part number, on order. kf_5002.xls 01/05/2002 5000HCS/ Part 3.58 3.59 3.60 3.61 3.62 3.63 3.64 3.65 3.66 3.67 3.68 3.69 3.70 3.71 3.72 3.73 3.74 3.75 3.76 3.77 3.78 3.79 3.80 3.81 3.82 3.83 3.84 3.85 3.86 3.87 3.88 3.89 3.90 3.91 Quantity Fold roll stub shaft Fold stop retainer Conveyor wheel assembly mount shaft Fold stop guide retaining shaft Fold Roll Fold Roll Stub Shaft - bottom Fold Roll Stub Shaft - top Bearing housing 2 2 1 1 2 1 1 1 Pivot bar 1 Divert plate Cover Plate Center Deflector Front Takeaway Wheel Shaft Takeaway Wheel Block Spring Spring Load Collar Front Takeaway Wheel Tie Bar Fold Stop Tape Bearing Housing Takeaway Roll Block mount Lock block Tape wheel Locking thumbscrew Rear angled bracket LHS Rear angled bracket RHS Top Cover Frame 1 1 1 1 1 1 1 1 Clinch cam block 1 2 1 1 1 1 1 1 1 1 1 Please quote machine model and serial number, with part number, on order. 49 50 51 52 53 61 54 55 48 1 47 2 3 4 5 46 8 9 62 10 45 44 43 11 42 4. Left hand side 41 40 12 22 39 13 38 14 37 36 23 35 16 24 34 17 25 18 19 C5002-4a 10.99 20 33 32 31 28,29 30 57,58 59 27 26 15 21 kf_5002.xls 01/05/2002 5000HCS/ Part Quantity 4.00 LEFT HAND SIDE 4.01 4.02 4.03 4.04 4.05 4.06 4.07 4.08 4.09 4.10 4.11 4.12 4.13 4.14 4.15 4.16 4.17 4.18 4.19 4.20 4.21 4.22 4.23 4.24 4.25 4.26 4.27 4.28 4.29 4.30 4.31 4.32 4.33 4.34 4.35 4.36 4.37 4.38 4.39 4.40 4.41 4.42 4.43 4.44 4.45 4.46 4.47 4.48 4.49 4.50 4.51 4.52 4.53 4.54 4.55 4.56 4.57 Bearing Housing Sprocket Chain Sprocket Sprocket 1 1 1 1 1 Ball race Nylatron runner Actuating Lever Shoulder Screw Block Plate Bar Chain link Pressure Plate Compression Spring Chain Sprocket Sprocket Chain - Fold Roll PCB bracket Sprocket - Idle Sprocket - Fold Roll Sprocket - Fold Roll Sprocket - Idle Sprocket Control PCB (SPRINTx) replaces 4.29 on 24V dc machines Control PCB (PSKF01) Mains line filter Staple Out PCB (PSKF04) where fitted Grommet Fold Roll Tension Spring Bearing Housing Feed roll lever limit Fold roll pivot lever Collar Collar Spacer Limit screw Fold Roll Tension Spring Fold roll pivot lever Sprocket Micro Switch Bracket Cover MicroSwitch Bearing Housing Pivot Plate Side Plate LHS Actuating Lever - Cover M/S Terminal Strip Terminal Strip Bearing Block Side Jog Fork Plate Spring Potentiometer 1 1 1 1 1 1 1 Relay 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Please quote machine model and serial number, with part number, on order. kf_5002.xls 01/05/2002 5000HCS/ Part 4.58 4.59 4.60 4.61 4.62 Quantity Relay base Transformer 1 1 Spring retaining plate Actuating Lever Return Spring 1 1 Please quote machine model and serial number, with part number, on order. 54 56 55 1 2 3 4 5 6 53 51 50 8 49 48 9 47 45 10 44 43 42 11 41 12 40 13 39 14 38 34 37 15 57 36 35 16 33 17 18 61 60 59 19 32 31 30 29 28 27 On newer machines, parts 59, 60 & 61 have replaced parts 29, 30 & 31. The two sets do not exist on any one machine. 26 25 24 5. Right hand side 23 22 21 C5002-5 10.99 kf_5002.xls 01/05/2002 5000HCS/ Part Quantity 5.00 RIGHT HAND SIDE 5.01 5.02 5.03 5.04 5.05 5.06 5.07 5.08 5.09 5.10 5.11 5.12 5.13 5.14 5.15 5.16 5.17 5.18 5.19 5.20 5.21 5.22 5.23 5.24 5.25 5.26 5.27 5.28 5.29 5.30 5.31 5.32 5.33 5.34 5.35 5.36 5.37 5.38 5.39 5.40 5.41 5.42 5.43 5.44 5.45 5.46 5.47 5.48 5.49 5.50 5.51 5.52 5.53 5.54 5.55 5.56 5.57 Bearing Housing Washer Bearing Block Side Jog Fork Plate Timing Pulley Bearing Housing 1 1 1 1 1 1 Pressure Plate Bearing Housing Compression Spring Fold Roll Tension Spring Block Fold roll pivot lever Collar Bearing Housing Collar Limit screw Fold Roll Pivot Lever Fold Roll Tension Spring 1 1 1 1 2 1 2 1 1 2 1 1 Bearing Housing Stacker Drive One-way Clutch Block Stacker Drive Link Collar Stacker Belt Drive Block Grommet Timing Pulley - Clutch Drive Timing Pulley - Motor Clutch Solenoid Clutch Assembly Clutch Bracket Clutch Retaining Bolt Timing Belt - Clutch Drive Spring Timing Cam - Top Takeaway Wheel Side jog cam plate Side Jog Cam Follower P-B Bush Collar Shaft Block Top takeaway roll actuating bar Cam Follower Timing Cam - Side Jog Pivot Bracket 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Timing Belt Pulley Shoulder Screw Bearing Housing Actuating Lever 1 1 1 1 1 Side Plate RHS Buffer Spring retaining plate Actuating Lever Return Spring Clutch pin 1 1 1 1 1 Please quote machine model and serial number, with part number, on order. kf_5002.xls 01/05/2002 5000HCS/ Part 5.58 5.59 5.60 5.61 Clutch Bracket (replaces item 5.31 on 240v AC m/c's) Clutch drive collar (replaces item 5.57 on 240v AC m/c's) Clutch Assembly (replaces item 5.29 & 5.30 on 240v AC m/c's) Quantity 1 1 1 NB:240v AC m/c's PCB have prefix 'PSKF'. 24v DC m/c's PCB have prefix 'SPRINT'. Please quote machine model and serial number, with part number, on order. 16 17 18 19 23 20 21 24 1 2 3 4 6. Outfeed conveyor 12 11 10 9 C5001-6 4.99 8 7 6 5 kf_5002.xls 01/05/2002 5000HCS/ Part 6.00 OUTFEED CONVEYOR 6.01 6.02 6.03 6.04 6.05 6.06 6.07 6.08 6.09 6.10 6.11 6.12 6.13 6.14 6.15 6.16 6.17 6.18 6.19 6.20 6.21 6.22 6.23 6.24 Deflector Plate Conveyor Mounting Bracket Conveyor Drive Shaft Conveyor Belt Drive Rolls Conveyor Belt Support Bar Plate Cup Bearing Conveyor Belt Drive Rolls Conveyor Front Shaft Conveyor End Stop Conveyor Table Quantity Conveyor wheel support bracket Conveyor wheel spindle Conveyor wheel Collar Conveyor wheel support bracket Thumbscrew 1 2 1 1 1 2 2 2 1 1 1 1 2 1 1 1 1 1 4 1 2 Nut plate Spring steel clip 2 2 Please quote machine model and serial number, with part number, on order.