Transcript
Inductive Bluetooth Wrist Watch
E a r p i ce
Spy Bluetooth Watch has a built-in 3.5 watt amplifier to drive all kinds of wireless earpieces within 40 cm. The Bluetooth wrist watch allows you to rest your hand on your desk and hear clearly via the spy invisible earpiece. -Compact and hidden design -Built-in rechargeable battery Hidden Bluetooth indicators are inside watch hands One tap to dial or answer phone calls Play music via mobile phone and easily adjust the volume FAKE clock. Not real clock function
Mechanical Diagram FAKE Watch Function Volume + Recharge Socket
Bluetooth Switch Blue Color Indicator Red Color Indicator
Volume Microphone
Wrist Band
Specification Item
Data
Frequency Range
2400~2480MHz
Audio Power
3 Watt
Transmission Distance
to earpiece < 40cm / to cellphone <10 meter
Bluetooth Compatibility
Bluetooth version 1.2 / 2.0
Integrated Microphone
Yes
Battery Type
340mah battery
Battery Life
Talking time 3 hours / Standby 180hours
Product Dimension & Weight
Watch L46xW42xH13mm Wristband W22xL82 & W22xL125mm
Package Includes 1 x Bluetooth wrist watch 1 x Recharge cable 1 x USB charger
PAGE
1
Inductive Bluetooth Wrist Watch
1 Recharge and Activation Before using the Bluetooth watch, please recharge for a few seconds to activate the battery. The Red light will turn on whilst recharging. Full recharge takes about 3 hours. When fully charged, the indicator will turn blue
2 Pair with Mobile Phone
3
A. Put the Bluetooth watch in pairing mode
Wear the Wrist Watch
1) With the Bluetooth watch powered off, press and hold Bluetooth switch for 6-10 seconds until both blue and red color indicators switch on.
Wear watch on left or right wrist dependant on
2) If Bluetooth is switched on or indicator is flashing, press and hold Bluetooth switch for 5 seconds to turn off Bluetooth, then repeat above step 1).
Audio should now be clear in the earpiece
B. Put Mobile phone in pairing mode 1) Go to mobile phone panel, turn on Bluetooth function and search for new Bluetooth device. 2) Select “T-Watch” then press “OK” or “YES”. 3) Enter password “0000" and press “OK”. * Once paired, indicator changes from flashing to blue. Some mobile phones need manual connection Note: If you can not switch on Bluetooth, please delete the paired devices and try again.
earpiece. Put hand on desk while sitting on the desk.
You can increase or reduce the volume using the buttons on the left hand side of the watch
4 Battery & Recharge To save battery power, please turn off power if not using for a long time. Turn off – Press and hold Bluetooth switch until indicator flash then switches off Turn on — Press and hold Bluetooth switch until indicator changes to blue color. If already paired with mobile phone and Bluetooth function in mobile phone is turned on, it will connect to mobile phone automatically. * Some mobile phone models do not support this function. The full performance of a new battery is achieved only after two or three complete charge and discharge cycles. The battery can be charged and discharge hundreds of times, but it will eventually wear out. When recharging the battery use only original default USB recharge cable and default wall charger. Do not leave a fully charged device on recharge power source. Overcharging may shorten battery life. If left unused, a full charged battery will lose its charge over time.
PAGE
2
Inductive Bluetooth Wrist Watch
Indicators
Operations Make a voice dial call End a call
Press Bluetooth switch and speak name after tone Tap Bluetooth switch
Solid red (Plugged into Adaptor)
Change Red to Blue
with adaptor plugged in
Battery Recharging Charging Completed
Receive a call
Tap Bluetooth switch
Reject a call
Press and hold switch until BEEP
without adaptor plugged in
Redial last call
Press and hold switch until BEEP
Answer a second incoming call
Press and hold switch (1st call on hold)
Blue and Red are turns on
In pairing mode
Toggle between two active calls
Press and hold switch
10 rapid flashes in Blue
Pairing Successful
Join a 3-way call (depends on phone)
Press and hold both volume swtiches
Connected
Put an active call on hold
Press and hold switch until BEEP
Slow pulse in Blue
Transfer a call from phone to BT
Tap Bluetooth switch
Mute or unmute call
Press Mute button
Send SOS alarm sound
Press SOS button
No indicator
Power use off
Troubleshooting Q. Why is not the neckloop working with my phone? A. Please make sure the Bluetooth is switched on in your mobile phone and that the neckloop is in pairing mode. Also mobile phone need to be within 10 meters from Bluetooth neckloop in open space. Try powering on/off the phone and neckloop and try again. Q. Why can I not pair with my mobile phone? A. 1) Make sure Bluetooth switch has power. Please recharge for 3 hours and try again. 2) Clear the paired Bluetooth devices and try again. Q. Audio is too quiet, why? A. The defined transmit distance from Watch to Earpiece is 40cm. Make sure there is no obstacle between them, such as the shoulder. Heavy clothes may also block the signal especially any metal materials Q. Why do I hear interference in invisible earpiece? A. If earpiece has no quality problem, the volume is likely too loud. Reduce the volume on the volume controller.
Warranty and return policy Default warranty is 12 months since ship date. We do not accept return if product has no quality problem. If product is within warranty and becomes faulty, you can return it for replacement or repair. No returns accepted for unwanted items for hygiene reasons
PAGE
3
