Transcript
1
SRS LIGHT DESIGN | The value of experience can be understood only when it is gained. It influences people, their decisions, it opens doors to new solutions and gives the ability to make something new and progressive.
Robert Sloboda
| SRS Light Design Rybnicna 36/D SK-83106 Bratislava Slovak Republic | www.srslight.com
[email protected] phone: +421 2 4468 1417 fax: +421 2 4468 1419
2
GLOSSARY SRS GENERATOR TM TECHNOLOGY
SRS STUDIO TM RISETIME
| SRS Generator is a technology that uses a unique
| SRS Studio Risetime guarantees that the Risetime of
module which makes it possible to run the dimming
the dimmer channels is not less than 400μs measured
devices even on generators that do not have stable
10-90% on nominal load. 400μs risetime is a top of
frequency output. The result is smooth dimming
value currently used in TV studios environment.
without any fuzziness.
SRS THERMALTM MANAGEMENT | SRS Light Design devices are 100% duty cycle rated
SRS 1P+N PROTECTION | A device equipped with the 1P+N protection of output channels requested by the some legal authorities.
– they can run at full load, continuously, for any length of time without overheating. The heatsink is big enough to keep the temperature on low level
SRS CUSTOMIZATION
guarantees reliability and long time functionality.
| We can offer you hardware or software customization
That’s the reason why our units are more than 30%
of the product. There is also the option to create a
heavier than competitors’ units.
brand new device according to your needs.
SRS S-DRIVE TM TECHNOLOGY
SRS RDM DEVICES
| Removes any barriers of the minimum load connected
| An DMX device equipped with the RDM module for
to the dimmer output. It does not matter whether you
remote monitoring and setting through the DMX in
are using the inductive load or resistive load – the
accordance with the RDM specification.
dimmer will always have smooth dimming, starting from the zero loads to the maximum loads.
SRS W-DMX® TRUE OUT
SRS WORLDWIDE USAGE | Devices created for worldwide usage, equipped with the full range power supply.
| Converts W-DMX® to the regular DMX signal and splits to all DMX outputs. This saves your money for additional W-DMX® receiver and also offers you the option to use the other DMX equipment connected to an W-DMX® true out capable device.
SRS SWITCH CONTROL | Device controlled by DMX and also by the switch – all over the DMX cable. That allows you to use the device without the DMX console even on small venues or as
SRS VARIOSPEED TM FAN | Mag-Lev fans are used. These fans are extremely quiet and have a life span that is almost ten times
a part of a scene controlled by actors on stage.
SRS 5 YEAR WARRANTY
longer than the bearing fan. We use variable speed
| Under our 5 year warranty, we guarantee repairs or
control depending on the inner temperature and load
replacements of our product without any fees, in the
of the circuits.
shortest time possible.
SRS ULTISENSE TM SOFTWARE
SRS LIFETIME WARRANTY
| Software allows you to communicate & configure
| No questions, no complains, no refused warranty
the entire range of SRS Ethernet capable devices
repairs. Repair or replacement of our product without
and S.net network. It offers comprehensive real-time
any fees in the shortest time possible. During warranty
status reports at any time.
repair we will supply a replacement device for free.
3
SPECIAL DEVICES MOTOR CONTROLLERS POWER DISTRIBUTION
PORTABLE DIMMING DATA DISTRIBUTION LED DIMMING
LED DIMMING
SPECIAL DEVICES
DATA DISTRIBUTION
MOTOR CONTROLLERS
PORTABLE DIMMING
POWER DISTRIBUTION
TOURING SYSTEMS
TOURING SYSTEMS
DIMMING
DIMMING
4
DIMMING
| NDPseries offers the highest quality of dimming available for any type of application – fixed or mobile. Excellent bullet-proof dimming with the latest high-end features: SRS S-Drive, SRS Studio Risetime chokes,
NDP SERIES
Ethernet communication, graphic LCD display with all information including bargraph, measured values, W-DMX® signal strength, DMX signal status, realtime monitoring of outputs and many other features packed in a solid metal case.
NDP12 – Variable power modules – Full-graphic LCD display with intelligent backlight – Multilingual interface – Simple navigation in menus with encoder and 2 buttons – Output load check – Ethernet port – 2 x DMX512 – USB port
OUTPUTS – Screw terminal – 12 x Schuko – 12 x French Schuko – 12 x Swiss – 12 x Danish – 12 x UK – 2 /4 x Harting® 16 pin – 3 x Harting® 10 pin – Harting® 24 pin – Socapex® 19 pin – 12 x CEE16A type 17
5
can be controlled via various signal sources: two DMX ports, W-DMX®, Ethernet protocols S.net, or ART-Net™ or simple just with the pre-programmed scenes or manual mode. | Future software update via an USB port takes only a few seconds.
NDP6 OUTPUTS – Screw terminal – 2 x Harting® 6 pin – Neutrik® powerCON 32 Amp – 6 x CEE32A type 17
DIMMING
| Thanks to the idea of network connection, NDPseries
6
ULTISENSE SOFTWARE
| UltiSense software is a JAVA based application
PROPERTIES
compatible with PC/MAC/LINUX platforms. It enables
– Dimming rooms
full control and configuration of the entire range of
– Racks/dimming units
SRS Ethernet capable devices and the S.net network.
– SRS nodes, CAT-5 extenders, RDM, ..
With remote access via Ethernet to the devices it opens new horizons in remote management in rental
SAVE, LOAD & COMPARE
or architectural environments and with comprehensive
– Projects snapshots
real-time status reports you have all necessary
– Project properties
information on your laptop, PDA or MAC.
– Installed/actual values – Power consumed on job/tour/totally
REAL-TIME MONITORING – Voltage & current of each phase
S.net NETWORK
– Temperature & frequency
– Based on Ethernet, CAT-5, 10/100Mbit
– Power factor
– Wired or W-FI connection with encoding
– Power consumption
– GSM connection for monitoring the installation
– Short circuit, No load, Load fail – Dimmer level, curves – W-DMX® – Uptime of all devices – Communication logs
7
DIMMING
S.net RENTAL STAGE
| With the SRS UltiSense computerized control system you have a complete real-time reporting facility and the option to setup the dimming with just few clicks. Software opens new horizons of the real Ethernet communication usage between all parts of S.net network. | The possibility to remotely reload settings to all racks on the stage via WI-FI or Ethernet access gives you the option to use your racks at many venues without
ULTISENSE PDA
spending time on manual setup. | We have created a simple and secure solution for all rental needs.
FOH
DESK
ULTISENSE
WI-FI S.net
S.net ARCHITECTURAL | With the SRS UltiSense control system you have a complete real-time reporting facility and an option to set-up the complete installation. | Communication over WI-FI and Ethernet is as simple and fast as your office. Option to have the WI-FI encoded and protected guarantee that your infrastructure is always protected. | We have created a simple and secure solution for all architectural needs. ULTISENSE PDA
S.net CONTROL ROOM
8
SERIES 400
| The series400 offers a reliable and affordable 3U 19” rack mount digital dimming solution with an integrated mains switch or RCD. With SRS Studio Risetime and SRS Generator technologies it’s the right choice for rental use. Proven design and huge spare capacity of components means that you can use this unit on tour with anyone, anytime.
DDP12 – 3U, 19” rack mount with integrated main switch or RCD – DMX512 – Analog 0-10V input – LCD display + encoder – Individual & block channel patching, preheats, curves – Electronic lock – LTP/HTP – Sequential test of outputs – Scenes / DMX fault scripts
OUTPUTS – Screw terminal – 12 x Schuko – 12 x French Schuko – 12 x Swiss – 12 x Danish – 12 x UK – 2 /4 x Harting® 16 pin – 3 x Harting® 10 pin – Harting® 24 pin – Socapex® 19 pin – 12 x CEE16A type 17
9
Navigation through the menu via encoder and two buttons is easy. The output bargraph is accessible through just one button. Setting of the unit takes only a few minutes.
DDP6025 OUTPUTS – Screw terminal – 2 x Harting® 6 pin – Neutrik® powerCON 32 Amp – 6 x CEE32A type 17
DIMMING
| The series400units have a simple and intuitive menu.
10 wall mount series
SERIES 400 WM
| The series400 WM fixed installation is designed to provide a reliable and affordable plug-in solution for architectural installations. Its low profile and well designed look, which is perfect for wall mount installations, SRS Thermal management and SRS Variospeed fans assure quiet and long-term operation. | Series400 WM is designed around the same components as the touring version of series400, with the same unique features proven in rental.
DDP12 WM OUTPUTS – Wall-mount with integrated main switch or RCD
– Screw terminal – 12 x Schuko
– DMX512
– 12 x French Schuko
– Analog 0-10V input
– 12 x Swiss
– LCD display + encoder
– 12 x Danish
– Individual & block channel
– 12 x UK
patching, preheats, curves
– 2 /4 x Harting® 16 pin
– Electronic lock
– 3 x Harting® 10 pin
– LTP/HTP
– Harting® 24 pin
– Sequential test of outputs
– Socapex® 19 pin
– Scenes / DMX fault scripts
– 12 x CEE16A type 17
11
– 2U, 19” rack mount – 6 x 10A outputs – DMX512 – Analog 0-10V input – LCD display + encoder – Individual & block channel patching, preheats, curves – Electronic lock – LTP/HTP – Sequential test of outputs – Scenes / DMX fault scripts
OUTPUTS – Screw terminal – 6 x Schuko – 6 x French Schuko – 6 x Swiss – 6 x Danish – 6 x UK – Harting® 16 pin – Socapex® 19 pin
DIMMING
DDP610
12
DP SERIES
| The DPseries is designed to provide an affordable, easy to setup and plug-in solution for architectural installations and special effects areas. Small weight, single phase operation and the possibility to customize predetermines it for use in clubs, TV scene applications with many channels with the low or medium power halogen/classic bulbs. DP32/DP16 have full-frame DMX synchronizing used in a matrix of bulbs creating video wall effects.
DP32 / DP16 – Wall mount – 32 x 0.5A or 16 x 1A outputs – Protection with fuses – Dimmer or switch – DMX512 – Screw terminal – Single phase operation
13
– 2U, 19” rack mount – 6 x 6A outputs with fuses – Single phase operation – DMX512 – Analog 0-10V input – 6 test buttons + indication – Preheat switch
OUTPUTS – Screw terminal – 6 x Schuko – 6 x French Schuko – 6 x Swiss – 6 x Danish – 6 x UK – Harting® 16 pin – Socapex® 19 pin
DIMMING
DP606
14
TOURING SYSTEMS
| Touring systems are designed as a modular system to provide an affordable and plug-in solution for touring. | Systems are produced with 24 up to 96 channels of dimming/hot power. The base of the touring systems is power distribution with optional metering followed by the NDPseries or series400 dimming units. Variable patch panels should easily fit to the back or the top of a unit.
INPUTS – IEC60309 – CEE form – Socapex® 19 pin – Harting® 10 pin – Harting® 16 pin – Harting® 24 pin – Twistlock – Powerlock
PROTECTION – Main switch, optional RCD – Optional 1P+N – Optional Hydromagnetic breakers
METERING – NDPmetering – Advanced metering – Simple metering
OUTPUTS – IEC60309 – CEE form – Socapex® 19 pin – Harting® 10 pin – Harting® 16 pin – Harting® 24 pin – Twistlock – Powerlock
15 PATCH
made flight cases always perfectly protecting your
– Wieland GST 18i3
system during transport.
– Wieland GST 15i2
| All touring systems have 5 year guarantee.
DATA DISTRIBUTION – DMX splitter – Optional W-DMX® – Optional communication module TOURING SYSTEMS
| Touring systems are packed in heavy duty custom
16
PORTABLE DIMMING
| Portable dimming devices are reliable and affordable dimming devices with one, four or six channels for TV studios, film and conditions where the ultra portable and quiet operation is required. Thanks to bullet-proof design in an aluminium mono-block and W-DMX® technology the Dimmer One and W-DMX® BAR are used at many venues with wireless operation.
DIMMER DP1 / DP3 – 1 x 10A – DP1: W-DMX® / DMX + fader, DP3: DMX + fader – C-clamp holder
DIMMER DP2 – 1 x 13A + MCB – Controlled by Fader – C-clamp holder
DIMMER DP5 / DP10 – DP5: 1 x 25A, DP10: 1 x 50A – Controlled by W-DMX® / DMX + Fader – Massive aluminum case
OUTPUTS – Schuko
– UK
– French Schuko
– CEE16A type 17
– Swiss
– CEE32A type 17
– Danish
– Neutrik® powerCON
17
DMX BAR
| DMX BARs are ideal for any venue where you need to distribute them around. With integrated SRS W-DMX® true output technology and separated DMX outputs close to the output socket they allow usage of the
PORTABLE DIMMING
LED fixtures.
DMX BAR 4CH
DMX BAR 6CH
– 4 x 5A dimmer/hot-power
– 6 x 5A dimmer/hot-power
– Aluminium 1.5m long
– Aluminium 2.2m long
– W-DMX® / DMX512
– W-DMX® / DMX512
– W-DMX® signal bargraph
– W-DMX® signal bargraph
– Tripod / C-clamp mounting points
– Tripod / C-clamp mounting points
OUTPUTS – Schuko – French Schuko – Swiss – Danish – UK
18
DATA DISTRIBUTION
| All W-DMX® products use the license free ISM band, and are certified for usage in the United States, Canada, Japan, and all EU countries. The SRS W-DMX® units use FHSS, Frequency Hopping Spread Spectrum, along with a number of other techniques to avoid interference and create a very reliable wireless link. W-DMX® devices are produced as compatible devices with other producers listed as OEM partners of Wireless Solution. | The initial configuration procedure is just as simple as with any other W-DMX® products – just one push of the button is all it takes to search for, and link every unallocated receiver | A choice of other antenna is available to increase the standard transmission range of 700m up to incredible 3200m.
APPROVALS – EU: EN 301 489-1, 301 489-17, EN 300-328-1, EN 300-328-2, EN 609 50 – USA: UQT-WDMXOEMPCBF – Japan: STD-T66 – Canada: ICES 003
W-DMX® TX – Wireless DMX transmitter unit – Interference free – W-DMX® Co-Existence mode – Point / Multipoint operation – Plug & Play – LED indicators
W-DMX® RX – Wireless DMX receiver unit – Interference free – W-DMX® Co-Existence mode – Point / Multipoint operation – Plug & Play – LED indicators
19 DSR8
| SRS DMX splitters are available in three, four, eight and ten channel formats. Housed in a 1U high 19”
– 1U, 19” rack/wall mount
rack mounting case or mounted on truss/wall, they
– 8 channel DMX splitter
provide the true optic isolation for all DMX lines used
– LED indication of DMX line status
on the stage.
– Termination switch with indication | LED indicators are checking both signal lines and deliver information when any problem occurs. Each output has a separate driver, optical-isolator and
DSR10
power supply to ensure the highest possible level of protection. Amplification allows extension of a DMX link above the maximum length specified by the
– 1U, 19’’ rack/wall mount
DMX512 standard. Up to 32 fixtures can be attached
– 10 channel DMX splitter
to each branch of a DMX line.
– LED indication of DMX line status – Termination switch with indication
DATA DISTRIBUTION
– Optional RJ45 connectors
DST3 – Truss/wall mount – 3 channel DMX splitter – LED indication of DMX line status – Termination switch with indication – SRS truss holders
DST4 – Truss/wall mount – 4 channel DMX splitter – LED indication of DMX line status – Termination switch with indication – SRS truss holders – Optional RJ45 connectors
20
DMX DE/MULTIPLEXERS
| The SRS’s Multiplexers and Demultiplexers are available in a 19” rack mounting case or a small metal enclosure. Demultiplexers with 16, 48 or 64 channels are fitted with 25-pin D type connectors for analog connection, DMX input/output and a low voltage power inlet.
DTA1664 / DTA1248 DEMULTIPLEXER – 64/48 x Analog 0-10V outputs – Sequential test function – Outputs are short circuit protected
DTA16 DEMULTIPLEXER – 16 x Analog 0-10V outputs – Sequential test function – Outputs are short circuit protected
ATD16 MULTIPLEXER – 16 x DMX channels with variable DMX start address – DMX test function
ATD1664 / ATD1248 MULTIPLEXER – 64/48 x DMX channels with variable DMX start address – DMX test function
21 | DMX devices housed in a DIN enclosure are an ideal solution for architectural usage. The wide choice of variants gives the engineers the opportunity to
DIN DEVICES
control the intelligent installation through the S.net,
DATA DISTRIBUTION
RS-232, RS-485, DMX or DALI interface.
type
function
DTA16-DIN
–
DMX 16 channels demultiplexer
ATD16-DIN
–
DMX 16 channels multiplexer
DTA8D8-DIN
–
DMX / 8 Analog 0-10V channels + 8 Digital outputs
DTS16R-DIN
–
DMX / 16 Relay switching channels
DTS16F-DIN
–
DMX / 16 N-Mosfet switching channels
type
dimming
DTD1-DIN
–
DMX.RS232 dimmer 1 x 300W
DTD2-DIN
–
DMX.RS232 dimmer 1 x 600W
DTD2-DIN
–
DMX.RS232 dimmer 1 x 1200W
DTD3-DIN
–
DMX.RS232 dimmer 2 x 300W
DTD4-DIN
–
DMX.RS232 dimmer 2 x 600W
DTD5-DIN
–
DMX.RS232 dimmer 4 x 300W
type
LED dimming/driver
DTL3.24
–
DMX.RS232 LED dimmer 3 channels 12-24V
DTL6.24
–
DMX.RS232 LED dimmer 6 channels 12-24V
DTL4.370
–
DMX.RS232 LED current driver 4 x 350mA
DTL4.700
–
DMX.RS232 LED current driver 4 x 700mA
DTL4.1000
–
DMX.RS232 LED current driver 4 x 1000mA
DTL6.350
–
DMX.RS232 LED current driver 6 x 350mA
DTL6.700
–
DMX.RS232 LED current driver 6 x 700mA
DTL6.1000
–
DMX.RS232 LED current driver 6 x 1000mA
22
LIGHT CONSOLES
| Housed in a 19” rack mounting case or a wall-mount version with an ultra low profile body, the SRS consoles are available in variety of sizes. All units are fitted with the DMX output, analog 0-10V output and optionally the W-DMX® output. With the USB module you are able to change the DMX start address or play the scenes from a USB key.
DAC18 – 3U, 19” rack/wall mount – 19x Long-life 60mm slide faders with dust cover – 19x Flash button – DMX + Analog 0-10V output
23 DAC12 – 3U, 19” rack/wall mount – 13x Long-life 60mm slide faders with dust cover – 13x Flash button
DATA DISTRIBUTION
– DMX + Analog 0-10V output
DAC6 – Wall mount ultra low profile body – 7x Long-life 60mm slide faders with dust cover – 7x Flash button – DMX + Analog 0-10V output – Custom RAL colors available
24
LED DIMMING
| In the past LEDs created their own segment in lighting industry. We were one of the first companies which established the 16bit resolution in LED dimming and many of our customers used them in TV studios, Theaters or Architectural environment. With the four year knowhow in driver/dimmer development for LED we have the complete portfolio of LED controlling devices. | It doesn’t matter if you are using LED tubes, LED fixtures or special LED modules – we always offer you the highest quality driver for your project. | Our know-how in creating the custom LED application
LD DEVICE
gives you, as a designer, option to create non-ordinary projects.
– 8 / 16bit Studio dimming – 3 / 4 / 6 channel LED dimmer – Variable power outputs – Variable voltage outputs 12V / 24V / 230V
LDC DEVICE – 8 / 16bit Studio LED driver/dimmer – 3 / 4 / 6 channel LED driver – Variable power outputs 350mA / 700mA / 1000mA
LDM DEVICE – Power and DMX for Mini-LED tubes – Variable power outputs 12V / 24V – Optically isolated DMX splitter – Neutrik® 4 pin output – Variable channels on device
type
LED dimming/driver
LD324
–
DMX LED dimmer 3 x 12-24V
LD3230
–
DMX Led dimmer 3 x 230V
LD624
–
DMX LED dimmer 6 x 12-24V
LDC435
–
DMX LED driver 4 x 350mA
LDC470
–
DMX LED driver 4 x 700mA
LDC4100
–
DMX LED driver 4 x 1000mA
LDC635
–
DMX LED driver 6 x 350mA
LDC670
–
DMX LED driver 6 x 700mA
LDC6100
–
DMX LED driver 6 x 1000mA
25 | ALDseries was created as the cost-effective solution for all LED applications. ALDseries devices aren’t equipped with the power supply so you can select
ALD SERIES
the right one according to the used LED tube or stripe, which saves money when other power supply is used in installation.
ALD DEVICE – 8 / 16bit LED dimmer – 3 / 4 / 6 channel LED dimmer – Variable voltage outputs 12V / 24V
ALC DEVICE – 8 / 16bit LED driver – 3 / 4 / 6 channel LED driver – Variable power outputs
ALV DEVICE – Custom module on request – Variable outputs on device
type
LED dimming/driver function
ALD 3D24
–
DMX LED dimmer 3 x 12-24V
ALD 6D24
–
DMX LED dimmer 6 x 12-24V
ALC 4REC3
–
DMX LED driver 4 x 350mA
ALC 4REC7
–
DMX LED driver 4 x 700mA
ALC 4REC10
–
DMX LED driver 4 x 1000mA
ALC 6REC3
–
DMX LED driver 6 x 350mA
ALC 6REC7
–
DMX LED driver 6 x 700mA
ALC 6REC10
–
DMX LED driver 6 x 1000mA
ALV 4AN
–
DMX / 4x0-10V + 4 x electr. ballast
LED DIMMING
350mA / 700mA / 1000mA
26
SPECIAL DMX DEVICES
| Housed in an easy to snap-in metal enclosure, the Projector Shutter is widely used in variety of projectors. The device provides video black-out by obstructing the light beam. The Ultra-torque servo offers precise movement even for big flaps needed for ultra wide lenses of a projector. | SRS switch control over DMX cable allows control of the device without DMX.
PROJECTOR SHUTTER – Fits most video projectors from small to large scale – Test / Mirror function switch – Ultra torque servo – Wide choice of projector flaps – DMX or switch controlled – SRS straps for easy fitting
iGENT CONTROLLER – Controll any RS232 / RS422 device over DMX: Projector, DVD player, ... – Optically isolated RS232, RS422, DMX 512 – Easy to configure via PC application – USB programming port – Optional W-DMX® – SRS straps for easy fitting
27
SWITCHING DEVICES
| This switching device allows you to control mains power remotely via a DMX line or a manual switch. All switching devices have 1P+N switching required by some regulatory authorities. Each model is equipped with a special 100A pulse resistant relay which allows long life function even in hard operational environments. | For special purposes we’re able to deliver custom
SPU32 / SPU16
switching units with an unlimited number of channels, various load per channel, with certification required
– Wall mount
by regulatory authorities.
– 32 x 0.5A or 16 x 1A outputs – DMX screw terminal – Single phase operation
DMX2SW / DMX1SW
DP10SW / DP5SW
– 2 x 8A or 1 x 16A switching channels
– 1 x 44A or 1 x 25A output
– DMX or switch controlled
– Controlled by W-DMX® / DMX + fader
– Optical signalization of output state
– Single phase / Three phase operation
– Variable outputs
– Schuko
– UK
– French Schuko
– CEE16 type 17
– Swiss
– CEE32 type 17
– Danish
– Neutrik® powerCON
SPECIAL DEVICES
OUTPUTS
28
MOTOR CONTROLLERS
| WMCseries is a unique device developed as replacement for the actual cable hoist controllers. WMCseries makes work with your hoists easier, faster and safer. This device allows riggers to control direction of one hoist or a complete hoist system from the local control or via a remote unit. The key
WMC SERIES
switch allows secure operation and prevents usage by unauthorized persons. | WMCseries is produced with 8 and 12 channels for both direct and low voltage control.
BASE UNIT FEATURES – 8 / 12 switches with LED indication – Green illuminated GO button – Emergency STOP button – Modes key-switch – Docking station + battery charger – Signal quality bargraph – Status & charger indicators
REMOTE UNIT FEATURES – Aircraft grade DURAL alloy with easy to hand fit – 8 / 12 switches with LED indication – GO and STOP button – Integrated antenna – Automatic sleep mode – Link connector – Belt clip – Motorola Li-Ion battery – 8-hours standby time
29 | MCseries is produced with 4, 8 and 12 channels for both direct and low voltage control. All units have fully automatic phase reversing – in any connection
low voltage direct control motor controllers
MC SERIES
of input phases the UP/DOWN directions are the same, which guarantees safe operation. | All controllers may be linked to form larger system movement of a pre-selected group. All controllers are ISO 13849-1, EN/IEC 62061 compliant.
TYPE – Direct control – Low voltage control
INPUTS – IEC60309 – CEE form – Socapex® 19 pin – Harting® 16 pin – Harting® 24 pin
PROTECTION – Main switch, optional RCD – Optional Hydromagnetic breakers
OUTPUTS – IEC60309 – CEE form – Socapex® 19 pin – Harting® 16 pin – Harting® 24 pin
MOTOR CONTROLLERS
– Powerlock
30
POWER DISTRIBUTION
| Distribution of mains power is the backbone of any performance, sound, lighting or vision system. Safety, reliability and compliance with the relevant standard are factors which ensure that your power distribution system will not only protect the people who use it, but also those who are legally responsible for the
PDU 15U
overall safety of the installation. | SRS power distribution devices are internationally recognised as reliable, of good value and solid construction. SRS manufactures a range of power distribution systems for touring and installation purposes. | All power distribution systems are designed, built, tested and comply with EN/IEC and CSA/UL standards.
| We have manufactured hundreds of PDUs on the basis of our customers’ visions. Starting from the sketch, we have found, created and delivered the optimal solution for any purpose – lighting, sound or vision. | In short, there is nothing to describe about a PDU – it’s just a custom made metal box, connectors, protections and power metering, but after many years in the business we know that quality and delivery time are the factors that matter. | Samples of produced PDUs will tell you more about our successful way of PDU manufacturing.
31 PDU 9U
PDU 6U
POWER DISTRIBUTION
PDU 3U
32
IPBOX
| SRS IPbox is a range of power distribution systems widely used in environments with high humidity or formation of condensed water. All units are boxed in a special plastic case and can be equipped with
– Humidity and formation of condensed water resistive – Aggressive gases and vapors resistive
any power connectors. With power metering build in the power distributor you’ll know actual load on each phase or power consumed on tour.
– Acid and hydroxide resistive – Vibrations and environmental effects resistive
| All power distribution systems are designed, built, tested and certified to meet the EN and CE standards.
– Power metering module – Compact design/stackable option
| They’re produced in many sizes customized according to your requirements.
INPUTS – IEC60309 – CEE form
OUTPUTS
– Socapex® 19 pin
– IEC60309 – CEE form
– Harting® 16 pin
– Socapex® 19 pin
– Harting® 24 pin
– Harting® 16 pin
– Powerlock
– Harting® 24 pin – Powerlock
PROTECTION – Main switch, optional RCD – Optional Hydromagnetic breakers
SRS LIGHT DESIGN | S SR RS Li Lig gh ht D De esign sig si gn n Rybn Ry bnic cn na a 36/D 6//D 6 SK K-8 831 3106 06 Brra attiisl is sllav a va ava Sllovak S ova ov ak k Rep pu ub bli lic ic | www. ww w ww. w.s srrsl slight ig ght ht.c .c com om sa sa ale lle es@ s@sr srs srsl sllig lig ght.c htt.c .com om ph p hon one e:: +4 42 21 2 4 44 46 68 8 141 417 fax: fa x: +42 421 2 44 4468 68 141 419 419
