Transcript
3M MATERIAL SAFETY DATA SHEET 3M (TM) NEUTRAL CLEANER CONCENTRATE (Product No. 3, Twist 'n Fill (tm) System) 04/25/2003
Material Safety Data Sheet Copyright, 2003, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME: 3M (TM) NEUTRAL CLEANER CONCENTRATE (Product No. 3, Twist 'n Fill (tm) System) MANUFACTURER: 3M DIVISION: Commercial Care Division ADDRESS: 3M Center St. Paul, MN 55144-1000 EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours) Issue Date: 04/25/2003 Supercedes Date: 10/02/2001 Document Group: 06-2097-1 Product Use: Specific Use:
NEUTRAL CLEANER CONCENTRATE
SECTION 2: INGREDIENTS Ingredient
C.A.S. No.
% by Wt
WATER HYDROXYALKYL AMINE OXIDES ISOPROPYL ALCOHOL 2-(2-ETHYLHEXYLOXY)ETHANOL FRAGRANCE
7732-18-5 68478-65-9 67-63-0 1559-35-9 Trade Secret
40 - 70 10 - 30 5 - 10 3- 7 0.1 - 1
SECTION 3: HAZARDS IDENTIFICATION 3.1 EMERGENCY OVERVIEW Specific Physical Form: Liquid Odor, Color, Grade: Bright, clear green-yellow liquid with citrus fragrance General Physical Form: Liquid Immediate health, physical, and environmental hazards: Combustible liquid and vapor. May cause severe eye irritation. May cause target organ effects.
3.2 POTENTIAL HEALTH EFFECTS Eye Contact:
Page 1 of 6
3M MATERIAL SAFETY DATA SHEET 3M (TM) NEUTRAL CLEANER CONCENTRATE (Product No. 3, Twist 'n Fill (tm) System) 04/25/2003
Severe Eye Irritation: Signs/symptoms may include significant redness, swelling, pain, tearing, cloudy appearance of the cornea, and impaired vision. Skin Contact: Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness. Inhalation: Single exposure, above recommended guidelines, may cause: Upper Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. May be absorbed following inhalation and cause target organ effects. Ingestion: Gastrointestinal Effects: Signs/symptoms may include stomach upset, nausea, vomiting and diarrhea. Target Organ Effects: Single exposure, above recommended guidelines, may cause: Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea, slowed reaction time, slurred speech, giddiness, and unconsciousness.
3.3
POTENTIAL ENVIRONMENTAL EFFECTS
A 3M Product Environmental Data Sheet (PED) is available. A conservative assessment indicates this product presents a low environmental risk. Components released to the environment through use and disposal are expected to have insignificant environmental impacts.
SECTION 4: FIRST AID MEASURES 4.1 FIRST AID PROCEDURES The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed. Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes. Get immediate medical attention. Skin Contact: Immediately flush skin with large amounts of water. If signs/symptoms develop, get medical attention. Inhalation: If signs/symptoms develop, remove person to fresh air. If signs/symptoms persist, get medical attention. If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES 5.1 FLAMMABLE PROPERTIES Autoignition temperature Flash Point Flammable Limits - LEL Flammable Limits - UEL OSHA Flammability Classification:
No Data Available 102 ºF [Test Method: Closed Cup] No Data Available No Data Available Class II Combustible Liquid
5.2 EXTINGUISHING MEDIA Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS Special Fire Fighting Procedures:
Wear full protective clothing, including helmet, self-contained, positive pressure or pressure Page 2 of 6
3M MATERIAL SAFETY DATA SHEET 3M (TM) NEUTRAL CLEANER CONCENTRATE (Product No. 3, Twist 'n Fill (tm) System) 04/25/2003
demand breathing apparatus, bunker coat and pants, bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head. Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and prevent explosive rupture. Unusual Fire and Explosion Hazards: Combustible liquid and vapor. Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information.
SECTION 6: ACCIDENTAL RELEASE MEASURES Accidental Release Measures: Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only non-sparking tools. Ventilate the area with fresh air. Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a toxic, corrosivity or flammability hazard. Collect as much of the spilled material as possible using non-sparking tools. Clean up residue with water. Collect the resulting residue containing solution. Place in a metal container approved for transportation by appropriate authorities. Seal the container. Dispose of collected material as soon as possible. In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE 7.1 HANDLING Avoid eye contact with vapors, mists, or spray. Avoid skin contact. Avoid breathing of vapors, mists or spray. Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep away from heat, sparks, open flame, pilot lights and other sources of ignition. Avoid contact with oxidizing agents. Keep out of the reach of children.
7.2 STORAGE Store away from acids. Store away from oxidizing agents. Store away from heat. Store out of direct sunlight. Keep container in well-ventilated area.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1 ENGINEERING CONTROLS NOTE: When used as directed and diluted and dispensed with a TWIST 'n FILL(TM) Chemical Dispenser, special ventilation is not required. Use in a well-ventilated area.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE) 8.2.1 Eye/Face Protection NOTE: When used as directed and diluted and dispensed with a TWIST 'n FILL(TM) Chemical Dispenser, eye contact with the concentrate is not expected to occur. Avoid eye contact with vapors, mists, or spray. The following eye protection(s) are recommended: Full Face Shield, Indirect Vented Goggles. 8.2.2 Skin Protection NOTE: When used as directed and diluted and dispensed with a TWIST 'n FILL(TM) Chemical Dispenser, skin contact with the concentrate is not expected to occur. Avoid skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials. Gloves made from the following material(s) are recommended: Butyl Rubber, Neoprene. 8.2.3 Respiratory Protection Page 3 of 6
3M MATERIAL SAFETY DATA SHEET 3M (TM) NEUTRAL CLEANER CONCENTRATE (Product No. 3, Twist 'n Fill (tm) System) 04/25/2003
NOTE: When used as directed and diluted and dispensed with a TWIST 'n FILL(TM) Chemical Dispenser, respiratory protection is not required. Avoid breathing of vapors, mists or spray. Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges. Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance. 8.2.4 Prevention of Swallowing Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES Type
Limit
ISOPROPYL ALCOHOL
Ingredient
ACGIH
Authority
TWA
400 ppm
ISOPROPYL ALCOHOL ISOPROPYL ALCOHOL ISOPROPYL ALCOHOL
ACGIH OSHA OSHA
STEL TWA STEL
500 ppm 400 ppm 500 ppm
Additional Information
Table Z-1A Table Z-1A
SOURCE OF EXPOSURE LIMIT DATA: ACGIH: American Conference of Governmental Industrial Hygienists CMRG: Chemical Manufacturer Recommended Guideline OSHA: Occupational Safety and Health Administration AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES Specific Physical Form: Odor, Color, Grade: General Physical Form: Autoignition temperature Flash Point Flammable Limits - LEL Flammable Limits - UEL Boiling point Density Vapor Density Vapor Pressure Specific Gravity pH Melting point Solubility in Water Evaporation rate Volatile Organic Compounds Percent volatile VOC Less H2O & Exempt Solvents Viscosity
Liquid Bright, clear green-yellow liquid with citrus fragrance Liquid No Data Available 102 ºF [Test Method: Closed Cup] No Data Available No Data Available > 200 ºF No Data Available No Data Available No Data Available 1 [Ref Std: WATER=1] 6-7 Not Applicable Complete Approximately 1 [Ref Std: WATER=1] 15 - 40 % [Test Method: calculated per CARB title 2] 55 - 100 % 200 - 1300 g/l [Test Method: calculated per CARB title 2] < 100 centipoise
SECTION 10: STABILITY AND REACTIVITY Stability: Stable. Materials and Conditions to Avoid: Strong oxidizing agents; Heat; Sparks and/or flames Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products Page 4 of 6
3M MATERIAL SAFETY DATA SHEET 3M (TM) NEUTRAL CLEANER CONCENTRATE (Product No. 3, Twist 'n Fill (tm) System) 04/25/2003
Substance
Condition
Carbon monoxide Carbon dioxide Irritant Vapors or Gases Oxides of Nitrogen
During Combustion During Combustion During Combustion During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its components.
SECTION 12: ECOLOGICAL INFORMATION ECOTOXICOLOGICAL INFORMATION Not determined.
CHEMICAL FATE INFORMATION Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS Waste Disposal Method: Incinerate in a permitted hazardous waste incinerator. As a disposal alternative, dispose of waste product in a permitted hazardous waste facility. EPA Hazardous Waste Number (RCRA): D001 (Ignitable) Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION ID Number 70-0708-3991-8 70-0710-0960-2
UPC 00-48011-20200-1 00-48011-23902-1
ID Number 70-0709-8999-4
UPC
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this material.
SECTION 15: REGULATORY INFORMATION US FEDERAL REGULATIONS 311/312 Hazard Categories: Fire Hazard - Yes Pressure Hazard - No
Reactivity Hazard - No
Immediate Hazard - Yes
Delayed Hazard - No
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA): Ingredient
C.A.S. No
2-(2-ETHYLHEXYLOXY)ETHANOL (GLYCOL ETHERS)
1559-35-9
% by Wt 3- 7
This material contains a chemical which requires export notification under TSCA Section 12[b]:
Page 5 of 6
3M MATERIAL SAFETY DATA SHEET 3M (TM) NEUTRAL CLEANER CONCENTRATE (Product No. 3, Twist 'n Fill (tm) System) 04/25/2003
Ingredient (Category if applicable)
C.A.S. No
Regulation
Status
ISOPROPYL ALCOHOL
67-63-0
Toxic Substances Control Act (TSCA) 4 Test Rule Chemicals
Applicable
CHEMICAL INVENTORIES The components of this product are in compliance with the chemical notification requirements of TSCA. This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION NFPA Hazard Classification Health: 2 Flammability: 2 Reactivity: 0 Special Hazards: None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
HMIS Hazard Classification Health: 2 Flammability: 2 Reactivity: 0 Protection: X - See PPE section. Hazardous Material Identification System (HMIS(r)) hazard ratings are designed to inform employees of chemical hazards in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency situations. HMIS(r) ratings are to be used with a fully implemented HMIS(r) program. HMIS(r) is a registered mark of the National Paint and Coatings Association (NPCA).
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
Page 6 of 6
