Sst-drop Dielectric Cables Fibers 1-12

Transcript

SST-Drop™ Dielectric Cables 1-12 Fibers Corning Cable Systems An Evolant® Solutions Product Description SST-Drop™ Cables offer the ease-of-installation of standard ALTOS® Cable in an easy-access single-tube design. Ideally suited for low-cost subscriber drop applications, the all-dielectic version of the SST-Drop Cable eliminates any bonding and grounding requirements. Optical drop cables are intended primarily for operation in the last portion of an all-optical network, such as fiber-to-the-home (FTTH) or fiber-to-the-business (FTTB) networks, bridging the space between the distribution network and the subscriber premises. The subscriber premises in this case is a residential property or small- to medium-sized business located in a facility that can be serviced by an optical cable having 12 fibers or less. Most applications will only require drop cables with two or four fibers. Typical drop cable distances are 100 m or less. PE Outer Jacket Water-Swellable Fiberglass Dielectric Strength Member Buffer Tube Fibers SST-Drop Dielectric Cables | Drawing ZA-2190 Features / Benefits • Aerial self-supporting or direct buried • All-dielectric design eliminates bonding/grounding • Works with industry-standard wedge clamps Cross-Section View of SST-Drop Cable | Drawing ZA-2191 • Available in preconnectorized assemblies • Standard ALTOS Cable buffer tube in an easy-access stranded single-tube design - Standard craft practices - Standard hardware compatibility • Exceptional crush resistance Product Specifications SST-Drop™ Dielectric Cables 1-12 Fibers Corning Cable Systems An Evolant® Solutions Product Specifications Storage Temperature -40° to +70°C (-40° to +158°F) Installation Temperature -30° to +70°C (-22° to +158°F) Operating Temperature -40° to +70°C (-40° to +158°F) Duct/Direct Buried Installation Maximum Tensile Loads Aerial Installation Maximum Tensile Loads Short-Term: 1350 N (300 lbf) Long-Term: 400 N (90 lbf) 1350 N (300 lbf) NESC Environmental Loading Condition 1% Installation Sag Maximum Span Sag at Environmental Distance m (ft) Loading (%) 3% Installation Sag Maximum Span Sag at Environmental Distance m (ft) Loading (%) Heavy 45.7 (150) 4.6 54.9 (180) 5.6 Medium 77.7 (255) 4.4 96.0 (315) 5.5 Light 132.6 (435) 4.1 173.3 (570) 5.4 Note: Longer spans are possible if maximum applied load is not exceeded during environmental loading. Span calculations require known initial loading (force or percent sag), cable weight and anticipated environmental loads. Corning Cable Systems Engineering Services will assist with span calculations for unique circumstances. Contact 1-800-743-2671 or +1-828-901-5000 internationally for more information. Information given is for aerial self-supporting installations. Fiber Count Buffer Tube Outer Diameter mm (in) Nominal Weight kg/km (lb/1000 ft) Nominal 1 Dimensions mm (in) Minimum Bend Radius Installed cm (in) 1-12 3.0 (0.12) 34 (23) 8.2 x 4.5 (0.32 x 0.17) 8.0 (3.15) 1 Actual dimensions may vary by ±5%. Packaging Options Convienent “Contractor-Sized” Packaging Gross Weight 65 lbs – no specialized equipment needed 609.6 m (2000 ft) Traditional Bulk Packaging (typically requires reel payoff equipment) up to 6096 m (20000 ft) Page 2 SST-Drop™ Dielectric Cables 1-12 Fibers Corning Cable Systems An Evolant® Solutions Product Transmission Performance Table Fiber Code K K C E Performance Option Code 30 50 31 00 Fiber Type 62.5/125 µm (850/1300 nm) 62.5/125 µm (850/1300 nm) 50/125 µm (850/1300 nm) Single-mode (1310/1383/1550 nm) Maximum Attenuation (dB/km) 3.5/1.0 3.5/1.0 3.5/1.5 0.35/0.35/0.25 Minimum LED Bandwidth (MHz•km) 200/500 200/500 500/500 –/–/– Serial Gigabit Ethernet Distance (m) 300/550 500/1000 600/600 5000/ – / – Ordering Information Contact Customer Service for other options. ■■■■ B 4-1 4 1 ■■ A 2 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Select fiber count (001 to 012). 1 - 4 Select fiber code (see Transmission Performance Table). 5 / 3 8 Select length markings. 4 = Markings in feet (standard) 9 12 Defines cable type. Defines tensile strength. 1 = 1350 N (300 lbf) B/A = SST-Drop™ Cable - 11 Select performance option code. (see Transmission Performance Table). 10 6 Defines jacket. 4 = Dielectric strength members/PE jacket 13 7 Defines fiber placement. - 14 Defines special requirements. 20 = No special requirements 1 = All fibers in same tube Page 3